Pink Noise
1) reference signal for audio test. 2) sleep enhancement aid.
See Also: Noise, White Noise, RF Noise, Noise Sources
-
Product
Low Noise Current Preamplifier
SR570
-
Stanford Research Systems, Inc.
The SR570 is a low-noise current preamplifier capable of current gains as large as 1 pA/V. High gain and bandwidth, low noise, and many convenient features make the SR570 ideal for a variety of photonic, low temperature and other measurements.
-
Product
High-Power Noise Sources
-
These modules not only contain the noise diode circuitry, but also gain stages to boost the output power. While lower frequencies (under 2 GHz) are most common, Mercury produces powerful amplified noise modules up to 18 GHz. Noise modules are available in coaxial, surface mount and pin type construction. TTL control options are available.
-
Product
TriaxM-TriaxM, Low Noise Triaxial to Triaxial Cable for SMUs, 1 m
785659-01
Triaxial Cable
The TriaxM-TriaxM Triaxial Cable connects your system to PXI Source Measure Units and other devices that have a triaxial connector. It uses guarding to remove the effects of leakage current and parasitic capacitance when … measuring very low current signals. The cable offers 300 V DC maximum voltage, 3 A maximum continuous current, 10 A maximum pulsed current, and different lengths.
-
Product
Low Noise Coaxial Cables For Sensors
-
Low noise coaxial cables are used with single axis and triaxial charge mode sensors. This table provides relevant specifications for four cable types. Type 003 is the most commonly used, but three other types are also available.
-
Product
HF Low Noise Amplifier
-
The COMM-connect HF Low Noise Amplifier can be used to amplify signals in the HF frequency range. The amplifier comes with a selection of 4 different connectors, which makes it very easy to adapt to any type of installation. Mechanical mounting is made easy by mounting flaps protruding the casing.
-
Product
Super Low Noise Amplifiers
WCA Series
-
WCA series super low noise amplifiers have sub-0.5 dB noise figure at VHF band with several octave bandwidth. The amplifiers have 75 Ohm impedance.
-
Product
Power Sensor and SNS Noise Source Cables (3 m/10 feet)
11730B
Power Sensor
The Keysight 11730 series power sensor cables are used with the 8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements.
-
Product
Noise Dosimeter
doseBadge5
-
The doseBadge5 is the next generation doseBadge noise dosimeter from Cirrus. It provides all of the unique features of the original doseBadge such as no controls, cables or displays with a range of new functions and features allowing it to be used for compliance with any occupational noise standard. Wireless communication to the dBLink App (for Android and iOS) or the doseBadge5 Wand allows the instrument to be configured and controlled without user intervention. Measurements can be scheduled to start, pause and stop automatically with the timer functions allowing the doseBadge5 to be deployed quickly and easily.
-
Product
Noise Figure Analyzer, Multi-touch, 10 MHz to 3.6 GHz
N8973B
-
The N8973B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8973B.
-
Product
Millimeter-Wave Noise Source, R-band, 26.5 to 40 GHz
R347B
-
The Keysight R347B noise source covers a 26.5 to 40 GHz frequency range. This waveguide noise source allows you to make accurate and convenient noise figure measurements on millimeter-wave devices. The R347B provides highly precise broadband noise at the input of the system or component under test. The noise figure meter then processes the ON/OFF ratio of noise power present in the system IF, and provides an accurate reading of noise figure and gain. The R347B noise source has remarkable ENR stability over time, which allows longer recalibration cycles and more accurate noise figure measurements.
-
Product
Mechanical Noise Tuner Control
S93027B
-
The S93027B enables to control Maury Microwave’s LXI tuner as the impedance tuner and measure the noise figure of unmatched devices (Gamma opt. < 0.9) with the N524xB PNA-X with option 029 and the S93029B noise figure measurement software.
-
Product
Noise Figure And Gain Test Extenders
-
SA full noise figure and gain test extender that extends the noise and gain measurement capabilities of common and low frequency signal synthesizers and noise figure meters to the frequency range of 110 to 170 GHz. This extender is designed to interface with industry standard noise and gain test systems.
-
Product
9KHz-2.1GHz, Spectrum Analyzer, Phase Noise<-98dBc/Hz, Amplitude Accuracy<0.7dB, 10.1" Color Display
T3SA3100
Spectrum Analyzer
9KHz-2.1GHz, Spectrum Analyzer, Phase Noise<-98dBc/Hz, Amplitude Accuracy<0.7dB, 10.1" Color Display.
-
Product
Low Phase Noise Frequency Synthesizer
-
Corech’s low phase noise frequency synthesizer series generates precise and stable frequency signals across a wide frequency range, available in SPI serial interface. These cost competitive, rugged and compact module are the ideal choice for RF & Microwave systems such as communication systems, test and measurement equipment, radar systems etc.
-
Product
Low Noise Amplifier
-
Low noise amplifiers, or LNAs, are designed and manufactured by utilizing the most advanced PHEMT or MMIC devices, thin film technologies, and an improved DC power supply to deliver a low noise performance with broad operating bandwidths and good gain flatness. While standard models focus on general purpose applications, additional models with differing frequency ranges, gains and noise figures are listed on the website. Custom designs are also offered to meet any user’s specific needs.
-
Product
Phase Noise Test System
PN9000 System
-
Noise eXtended Technologies S.A.S.
The PN9000 is a simple and fast Automatic Phase Noise Test System covering a very wide frequency range. Its modular architecture allows optimum configuration, multiple measurement techniques and future growth in a NIST tested instrument.
-
Product
Environmental Noise Monitors
-
Our noise monitoring equipment is used across a wide range of applications and location. Each of these systems has been designed to meet the exact needs of the user by combining noise monitors with a software and support package.
-
Product
Noise Sources
WGNS
-
The system allows the user to extend the frequency range of the NFA to allow for accurate noise figure measurements to be performed on a device operating in the 26.5 – 170GHz range on wafer as well as in benchtop applications. Farran offers the WGNS series of noise sources to be used in conjunction with the FBC down converters for use as frequency extenders for noise figure measurement test system.
-
Product
Phase Noise Analyzer
NXA-50
-
This new NXA-50 is a sea-change in Phase Noise Test Systems. Making both residual and absolute noise measurements out to 50 GHz, this self-contained instrument uses either internal or external references with cross correlation for maximum dynamic range.
-
Product
Noise Receiver Modules And Noise Switching Modules
MT7553 Series
-
Noise Parameters are the non-50Ω extensions of Noise Figure, and are an important modeling and model validation tool to understand how a device-undertest’s performance changes as a function of source impedance. Noise Parameter measurements are typically performedusing a Vector Network Analyzer (VNA) to measure the S-Parameters of the DUT, and a Noise Analyzer (either Noise Figure Analyzer NFA or Spectrum Analyzer SA) to measure the noise power of the DUT. Noise parameters are calculated from a combination of knownsource impedances, S-parameters and noise powers.
-
Product
Industry Standard in Noise Measurement
PN9000
-
The PN9000 is a simple and fast Automatic Phase Noise Test System covering a very wide frequency range(2 MHz to 140 GHz). Its modular architecture allows optimum configuration, multiple measurement techniques and future growth in a compact instrument.
-
Product
Noise Figure Analysis Using NI PXI RF Test Instruments
NI-RFmx Noise Figure
Test Instrument
Measure noise figure, gain, Y-factor, effective temperatures, hot and cold power, and moreOptimized calibration and measurement routines for multi-DUT test using Y-factor and cold sourceSupports the PXIe-5668R 26.5 GHz VSA, the PXIe-5698 26.5 GHz preamplifier, and VSTsDesigned for use with industry-standard noise sources such as the Noisecom NC346 Series
-
Product
1/2.5" 5.0 MP Low Noise USB Camera (Color)
See3CAM_CU55
-
See3CAM_CU55 is a 5.0MP USB3.1 Gen1 UVC Color Camera with S-mount (also known as M12 board lens) lens holder. It is a two-board solution containing camera sensor board based on 1/2.5" AR0521 image sensor from ON Semiconductor and USB3.1 Gen 1 Interface board. The powerful on-board Image Signal Processor (ISP) brings out the best image quality of this 2.2micron pixel 5MP AR0521 CMOS image sensor making it ideal for next generation of high resolution surveillance, biomedical instruments and biometric authentication applications.
-
Product
Noise Figure Measurements With Vector Correction
S95029B
-
The S95029B noise figure application enables high-accuracy noise figure and noise-power measurements of amplifiers, frequency converters, and mixers by using the Keysight vector-source-correction technique. Using a source-impedance tuner to remove the effects of imperfect system-source match, this technique produces higher accuracy results than Y-factor method and other cold-source implementations--especially for in-fixture, on-wafer, and automated-test environments.
-
Product
Phase Noise Measurement Solution, 50 kHz to 110 GHz
E5505A
-
The Keysight Technologies E5500 Series of phase noise measurement solutions offers the most flexible set of measurements on one-port VCOs, DROs, crystal oscillators and synthesizers. Two-port devices, including amplifiers and converters, plus CW, pulsed and spurious signals can also be measured. The E5500 measurements include absolute and residual phase noises, AM noise, and low-level spurious signals. The stand-alone instrument architecture easily configures for various measurement techniques, including the PLL/reference source technique, residual and FM discriminator methods.
-
Product
Advanced Low-Frequency Noise Analyzer
E4727B
-
Get a deeper, closer look at low frequency noise with the A-LFNA integrated with WaferPro Express, featuring data analysis, wafer prober control and test suite automation.
-
Product
Noise Activated Warning Sign
SoundSign
-
The SoundSign Noise Activated Warning Sign is a visible, effective way to warn workers and staff of high noise levels.
-
Product
Dual Channel Noise Dosimeter
SV 102+
-
The SV102 + is our latest dual-channel noise dosimeter and replaces our ground breaking SV102. It has been designed for the accurate measurement of noise exposure to ISO 9612 and MIRE (microphone in real ear) measurements to ISO 11904-1.
-
Product
Low Noise Amplifier
LNA
-
Teledyne Defence & Space (TDS) Low Noise Amplfiers (LNA) are designed to amplify very low power signals without degrading the signal-to-noise ratio.An amplifiers is designed to increase the power of both the signal and the noise however the Low Noise Amplifier is specifically designed to minimise the additional noise so important information should not be lost.
-
Product
Durability, Noise & Vibration Test Platform
LMS Test.Lab
-
Siemens Digital Industries Software
LMS Test.Lab with faster, more accessible and more complete test-based engineering for noise, vibration and durability. From multichannel data acquisition to a full suite of testing, analysis and reporting solutions, LMS Test.Lab 15 provides you with a versatile and rigorous problem-solving toolkit.
