Mezzanines
Is the stacking of cards into a single card that then plugs into the computer bus or data path.
-
product
Mezzanines
Our mezzanines are available with fiber optic or electrical outputs and enable a high-degree of signal processing options and high data rates. Mezzanine electrical interfaces may be software defined for even more versatility and signal inspection/processing options. These mezzanines are interoperable with similar fabric building blocks that have a compatible mezzanine site for low-risk processing, subsystem pre-integration.
-
product
XMC Mezzanine Processor
XMC-121
Curtiss-Wright Defense Solutions
Designed for space-constrained size, weight and power (SWaP)-sensitive programs, the XMC-121 small form factor Intel Xeon x86 single board computer (SBC) offers extremely powerful x86 processing with a low power and small sized footprint.
-
product
Basic CMC Extender for PrPMC, PMC, and PMC-X
4320
Basic CMC Extender for PrPMC, PMC, and PMC-X. The Basic Common Mezzanine Card (CMC) extender provides a means to extend IEEE 1386 boards for signal accessibility. PrPMC (VITA 32), PMC (IEEE 1386.1), PMC-X (VITA 39) and any other CMC-derived board is supported.
-
product
Intelligent CPCI Quad Industry Pack Carrier
CPCI-6713-4 IP
The board consists of private SDRAM and Flash memory attached to the 300 MHz TMS320C6713B DSP. An FPGA provides the timing and control. Peripherals include a serial port and connectors for IP mezzanine boards. Flash memory is availablefor downloading programs into a non-volatile memory. A PCIbus connector provides the interface to the host computer. A serial port is available for debugging.
-
product
Time to Digital Converter-1ns 5ch
FMC TDC
Sundance Multiprocessor Technology Ltd.
An FPGA Mezzanine Card (FMC) with a Time to Digital Converter chip to perform one-shot sub-nanosecond time interval measurements.
-
product
Shelf Manager Carrier/Mezzanine Board fix-mounted for CompactPCI
064-754
Set of Shelf manager mezzanine board installed on the fix mounted carrier board. The fix mounted carrier board provides all interfaces via headers for easy access and can be used directly inside of your system platform.
-
product
3U VPX PMC/XMC Carrier Board
IC-CMC-VPX3b
The IC-CMC-VPX3b is a carrier board designed to expand 3U VPX system capabilities with the integration of PMC/XMC mezzanines.
-
product
Advanced Mezzanine Card (AMC) Module
AMC SyncClock32
The AMC-SyncClock32 from Brandywine Communications is an Advanced Mezzanine Card (AMC) module. Precision time is provided to the host computer with zero latency. The onboard microprocessor automatically synchronizes the clock to reference signal inputs. The reference signal inputs handled by the AMC in its standard configuration are IRIG’s A, B/IEEE1344, and NASA 36. Alternatively, the clock in the AMC can be set using commands from host computer and free run using its on-board oscillator as the time base.
-
product
PXI Express Board Virtex-5 Dual ADC/ DAC module
SMT750
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
product
Mezzanine System
5188
ECM P/N 5188 provides an AD8109 crosspoint switch for analog or digital signals with 250MHz of Bandwidth. For single ended applications 8 inputs can be connected up to 8 outputs in any configuration.
-
product
4-Channel ADC FMC Module
FMC103 – LPC
Sundance Multiprocessor Technology Ltd.
The FMC103 is a four-channel ADC FMC (FPGA Mezzanine Card) which is fully compliant with the VITA 57.1-2010 standard. The FMC103 card provides four 12-bit 210 MSPS A/D channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available. The FMC103 has the LPC (Low-Pin Count) 160-Pin connector, front panel I/O, and is conduction cooled compliant. The board is also available with Mil-I-46058c compliant Conformal Coating.
-
product
Carrier Card
PEX442
The PEX442 Mezzanine Carrier Card allows designers the flexibility to extend and expand the IO capability of their systems by supporting high bandwidth links to combinations of XMC, PMC and AFIX (Additional Flexible Interface Xtensions) modules using PCI Express infrastructure.
-
product
Voltage Meter
МН32СМ
The mezzanine module (mezzanine) МН32СМ is designed to measure instantaneous voltage values over thirty two two-wire differential channels.
-
product
XMC Processor Cards
Curtiss-Wright Defense Solutions
Our XMC mezzanine cards provide an easy way to add processing power and meet performance requirements within the most demanding size, weight, and power (SWaP) constraints. Create a zero-slot solution by mounting the mezzanine on a graphics or FPGA card or on the power supply of a Curtiss-Wright 3U or 6U computing system.
-
product
FMC, XMC & PMC
The FPGA Mezzanine Card is used by Data Patterns to implement signal interface with external world compatible FPGAs mounted on the FMC carrier there are primarily used for high speed analog interface for digitization (ADCs) and waveform generation (DACs). This form factor is also utilized for special I/O Interfaces such as various avionic protocols and buses. FMC I/O signals may be routed via front panel connectors or through Mezzanine connectors that route the signal back to the carrier board for routing through rear I/O of the Chassis. The system interface is designed for routing to FPGAs using a VITA 57 0.05 Pitch Terminal Array Assembly.
-
product
Interface Module
MRS4
The mezzanine provides connection of up to four input and four output interface lines.
-
product
Transceiver
MT
Mezzanine MT (mezzanine transceiver) is designed to receive and transmit microwave signals in the frequency range from 70 to 6000 MHz. The MT transceiver is a new generation device designed using the most modern element base and designed for use in modern measuring systems based on the open standards AXIe, VXI and LXI.
-
product
Voltage Meter
MN4I
M-module MN4I is a mezzanine module designed to measure the voltage of constant and low-frequency signals through four galvanically isolated channels from each other (four-channel digitizer).
-
product
1-2 Independent, Dual Redundant 1553 Channels on Small Mezzanine
MEZ-E1553
From our popular ENET product, the MEZ-E1553 is a small, rugged mezzanine product that can easily be integrated into your system design. Alta provides full reference schematics, design notes, STEP 3-D Files, and sample ESS test programs. Guaranteed 1553A/B/C compliant with AS4111 5.2 Protocol Test reports.
-
product
FPGA Mezzanine Card
FMC126
The FMC126 is a quad-channel multi-mode A/D FMC, fully compliant with VITA 57.1 standards.The card provides four 10-bit ADC channels that enable simultaneous sampling of 4, 2, or 1 channel with a maximum sample rate of 1.25 GSPS (4-channel mode), 2.5 GSPS (2-channel mode), or 5.0 GSPS (1-channel mode).
-
product
Mixed function mezzanine side card for CPCI-S CPU boards
SCX-PCIE
The SCX-PCIE is a mezzanine side card for EKF CPU boards, equipped with a PCIe® Gen3 packet switch, onboard NVMe and SATA mass storage, and high-speed front I/O.
-
product
Mezzanine FMC
FMC-520
Curtiss-Wright Defense Solutions
Through direct connection to a host FPGA, the FMC-520 provides a low cost, low latency path necessary for agile applications such as RADAR and EW. Conforming to the VITA 57 FMC standard, the FMC-520 simplifies developers’ integration of FPGAs and analog output into embedded system designs.
-
product
Digital Digitizer
MOS2
Mezzanine module (mezzanine) MOS2 is designed to convert instantaneous voltage values of an electrical signal into a digital code, measure instantaneous voltage values. The mezzanine is intended for use in HF and microwave systems as a terminal device for digitizing intermediate frequency signals up to 200 MHz. Together with the frequency converter DOWNCONVERTER 10 GHz LXI manufactured by the holding "Informtest" MOS2 under the control of the common software shell ACM2 makes up a synthetic instrument - spectrum analyzer, a ready-made solution for testing microwave devices and radio reception channels.
-
product
Interface Module
MC
The MC mezzanine module is designed to receive external commands and issue synchronization pulses on the TTLTRG line (for VXI and other devices) and the LVDS line (for LXI devices).
-
product
FPGA Mezzanine Card
FMC116
The FMC116 is a 16-channel ADC FMC daughter card which is fully compliant with the VITA 57.1-2008 standard. The FMC116 provides 16 A/D 14-bit 125Msps channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available.
-
product
Voltage Meter
MDS32
M-module MDS32 is a mezzanine module designed to analyze the state of discrete sensors. М-module MDS32 is installed on the mezzanine carrier - module НМ-М and connected to it via a local information highway. Up to four m-modules of various types can be installed on the NM-M module. The NM-M module together with the m-modules installed on it forms a C-1 VXI module for 64 analyzing channels and is used to create information measuring VXI systems.
-
product
FMC Mezzanine Module, 4 or 8 Channel
NES-FMCSER
Sundance Multiprocessor Technology Ltd.
The FMC specification was developed to enable FMCs to be supported on a wide range of existing form factors including but not limited to, PCIe, VME, CompactPCI, VXS, VPX, VPX-REDI, AdvanceTCA and AMC. Up to three FMCs can be fitted on a 6U VPX carrier.
-
product
Resistance Meter
MT16-4L
М-module МТ16-4Л is a mezzanine module (hereinafter referred to as a mezzanine), designed to measure the resistance of resistive sensors using a four-wire measurement circuit in sixteen channels (sixteen-channel digitizer). М-module МТ16-4Л is installed on the mezzanine carrier - module НМ-М and is connected to it via a local information highway. Up to four mezzanines of various types can be installed on the NM-M module. The NM-M module, together with the mezzanines installed on it, forms a VXI module of the C-1 size and is used to create information measuring VXI systems.
-
product
Mini Module
COMeT10-3900
The COMeT10-3900 is an industrial COM Express® Type 10 Mini module with an Intel Atom® E3900 processor. This low power, industrial module was designed and manufactured in the USA. The small form factor module is designed as a processor mezzanine that can be plugged onto a carrier board that contains user-specific I/O requirements.
-
product
FPGA Mezzanine Card
FMC424
Electrically compliant with the VITA 57.1 standard, the FMC424 is compatible with Abaco Systems' FPGA carrier cards offering high pin count connectors. It also allows for the option to stack an additional FMC over it.
