-
product
Telemetry Transmitter
TT22 Series
Systems Engineering & Management Company
The TT22 series of 0.25W telemetry transmitters are designed to transmit data in the frequency bands covering 1710-1850 MHz or 2185-2485 MHz. These transmitters are true FM, modular, all solid state and are protected for operation into any VSWR, without damage, including open or short circuit.
-
product
Bolt Extensometers for Proof Load Testing
Model 3565
Jinan Testing Equipment IE Corporation
The Model 3565 uses hard conical points to contact the bolt at the center of the head and at the bottom. It is fully adjustable for different length bolts ranging from 25 mm (1 inch) in length to 150 mm (6 inches) standard. Extension beams are available for longer bolts. The standard maximum measuring range is 1.25 mm (0.05 inches). Generally, on longer bolts this extensometer will be self-supported without requiring any centering marks or punch marks on the bolt. For shorter bolts these marks may be required. If the conical pins are sharp, marks are often not needed even on the shortest bolts.The extensometer has a zero adjustment screw to adjust the length between the contact pins. This is used to set the output voltage to zero, which corresponds to the correct starting position for the test. It also includes a breakaway lower arm. In the event a bolt should fail, the breakaway arm snaps free, helping to prevent damage to the extensometer. This is easily re-installed. In the event that bolt failures are likely during a test, it is recommended the user attach a cord around the upper part of the beam and tie the other end to the test frame to prevent the extensometer from falling. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 3565 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
96-Pin SCSI Micro-D Straight PCB
40-963-096-SF
Ideal for user created termination schemes where the termination is to be on the front of the product or remotely connected to the module by cable. Suitable cables for this product are detailed in the data sheet. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
product
Dual / Quad Digital Multichannel Analyzer
781 MCA Family
The 781 MCA family integrates advanced firmware algorithms operating Digital Pulse Processing for Pulse Height Analysis (PHA). The processing algorithms can be easily adapted to different detectors and application ensuring effective data analysis even at high count rates. It provides advanced tools for configuring baseline restoration and pile-up rejection. Thanks to the multiple input simultaneous acquisition, the module is able to manage coincidence and anti-coincidence logic between detectors, allowing the user, for example, to easily take advantage of background rejection or anti-Compton techniques.
-
product
Thermometer, 2 Channel, 0°C to +1767°C, 175 mm, 85 mm, 30 mm
72-7715
Compact handheld thermometer is ideal for a variety of industrial, residential, HVAC and equipment testing applications. It accepts a wide variety of industry standard thermocouple probes and features internal data logging of up to 100 records. Dual inputs allow simultaneous measurement of two separate zones with independent readout or differential (T1-T2) display
-
product
Recording System
Surveyor DFR DDR
The Surveyor Recording System is a DFR/DDR with local Input Modules connected to a Controller. The Input Modules are connected to the Controller by multiconductor cables. The Controller contains a single board computer running 64-bit Microsoft Windows 10® and the E-MAX Director program, for recording, storing and transferring data.
-
product
ESI(Electronics Systems Integration Unit)
MS 2004
The ESI subsystem provides platform interfaces like Gyro and on board Radar Blanking. This unit receives Analog and Digital GYRO inputs from ship and pre- trigger pulses from on board radars of the ship. This unit measures and provides the ship heading data to VARUNA ESM system. It also provides Heading, Roll and Pitch data to the ECM system. This unit also generates band wise composite ESM Rx. Blanking gates and provides all the required interfaces to ESM receiver, ECM System and System Controller units.
-
product
ZIPLEVEL EZDepth
The revolutionary ZIPLEVEL EZDepth is an inexpensive alternative to costly cab based digital depth instruments. EZDepth is built from the core of the quarter century proven ZIPLEVEL PRO-2000…the world’s only pressurized, bubble free High Precision Altimeter. Unlike conventional technologies, EZDepth installs in minutes to directly display depths over unlimited ranges without line-of-sight, satellite horizons or complex arrays of inclinometer sensors. Its optional ZIPLEVEL SmartLink sends data to smart devices on your panel or up to 100’ away for real time profiles and tables or elevations plotted on site photos (Pat. Pend. ZIPLOT) for instant sharing of documentation before, during and at the end of your project.
-
product
Decelerometer
Maschinenbau Haldenwang GmbH & Co. KG.
National type approval by the PTBPrinter with keyboard and digital displayFast matrix printer with graphic expressionPiezoelectric decelerometersControl and measurement electronicsElectrical equipment adjustment by means of digital displayGyro sensor for automatic compensation of the measurement error by the pitch behavior of the vehicleJacks for pedal force, pressure u. Load indicatorRS-232 interface to PC with data transfer for standard table SoftwareChargerSpare roll of paper approximately 15 mplastic suitcase
-
product
Sound Level Meters
Complies with IEC 61672-1 class 2 standard, Measures Leq, MaxL, MinL, SPL, 64,000 Records Data Logger, PC interface
-
product
PCI-5124 , 150 MHz Bandwidth, 200 MS/s, 12-Bit PCI Oscilloscope Device
779171-03
150 MHz Bandwidth, 200 MS/s, 12-Bit PCI Oscilloscope Device—The PCI-5124 high-resolution oscilloscope device has two channels that sample up to 200 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for both time-domain and frequency-domain applications that require high-resolution measurements with up to 150 MHz of analog bandwidth.
-
product
Analog And Digital Sensor Measurement Data For CAN Applications.
K- AN8
The stackable K-AN8 is our cost effective solution to measuring analog and digital/PWM sensors together in one module. Extremely easy to use and stackable with all of our other K-series instrumentation modules. The K-AN8 includes our unique power down and WakeOnCAN feature for quick installation on long term unattended fleet test vehicles.
-
product
Multi Channel Waveform Acquisition and Spectrometer Card
Pixie Hybrid
The Pixie Hybrid is a multi channel all-digital waveform acquisition and spectrometer card. It provides a compact, fully featured solution to a variety of data acquisition needs.
-
product
3D Metrological Software
InnovMetric PolyWorks
Powerful metrological software which can effectively process vast amounts of data from 3D scanners in real time. Due to its modular architecture the software covers a large number of applications: one-point inspection by touch measurement systems, scanned data processing and data comparison to CAD models or complete reverse engineering – CAD model creation.
-
product
Analysis Software
The Waveform Processing Software AS-70 reads data from WAVE files and offers a wide range of functions, including graph display, level processing, frequency analysis(FFT analysis and octave band analysis), file output, and playback.
-
product
8 SE Or 4 Diff. Input Channels, 8 Analog Output Channels, PCI Express
APCIE-3121-8-8
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
DH Series Tip - CrossSync PHY PCIe5 CEM x16
DH-CSPHY-PCIE5-CEMX16
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
Thermohygrometer
Are suitable for monitoring ambient temperature and humidity, and have recording and Bluetooth communication functions. They can be used in combination with mobile APP. Users can instantly read the parameters measured by the instrument or export the data recorded by the instrument for analysis through the mobile APP. deal with.
-
product
Activity Detection Unit
DG009-M1
Many advanced EW receivers, particularly those associated with ECM jamming systems, do not require the high resolution frequency information associated with a DFD or IFM based receiver. This is typically the case where a single pulse present within a broad frequency band is required to be detected and instantaneously down-converted to an IF band.TDS manufactures a range of Frequency Activity Detectors (FADs) also known as Activity Detection Units (ADU) which perform frequency measurement of an RF pulse and output data in as little as 15ns. The basis of these products is TDS’s ability to produce high performance broadband channelisers and integrated detectors. These devices are ideal for receivers which must operate in very high pulse density environments.
-
product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787457-01
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
product
Advanced Serial Protocol Analyzer
Most data networks are complicated, not just the hardware and network issues, but also the high-level protocols that devices use to communicate; and to make things even more complicated, many manufacturers have incorporated proprietary protocols for their devices. Integrating different devices and protocols within a data network is always the most challenging task for system integrators, firmware / software developers, and site engineers. From the simplest loopback test to complicated checksum calculation and sophisticated firmware and GUI software development, the 232Analyzer is designed to tackle all these challenges.
-
product
PCIe 16 Bit High Speed Digitizer - 180 MS/s on 2 Channels
M4I.4470-X8
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
SFP BIDI
2.5 Gbps LC BIDI
Is specifically designed forhigh performance integrated duplex data link overbi-directional single mode optical fiber. Thehigh-speed laser diode and photo diode areprovided as a light source and a detector,respectively.
-
product
Anemometers
Guangzhou Amittari Instruments Co.Ltd
Widely used in data collection for boiler, refrigeration industry, ventilation duct, environment monitor, navigation measurement, weather forecast, collection of the weather datum for outdoor busywork and fire department.
-
product
ASC 3.0 Datacasting System
SkyScraper XM
SkyScraper® XM is a state-of-the-art data broadcasting system for distributing public and private digital content and NRT applications over ATSC 3.0 and hybrid networks. Using SkyScraper XM, TV stations, corporations, and other organizations can reach their targeted audiences, add revenue sources, and bridge digital divides.
-
product
Ground Tactical Data Link System
Curtiss-Wright Defense Solutions
Fulfilling the increasing need for secure, reliable, and efficient communication systems in the battlefield, TCG GTS is an affordable and combat proven TDL solution with comprehensive situational awareness (SA), command and control (C2) and non-C2 data link capabilities.
-
product
Fibre Channel Test & Simulation Interface for PCI
PCI-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
Shock Tester
DP-1200
King Design Industrial Co., Ltd.
Shock or bump test mainly simulate the impact effects of product and its components encountered in usage and transit process. Through standard and high-reproducibility instant energy exchange, you can analyze the product ability to tolerate the strong external stress and the degradation of structural weaknesses to quickly obtain the data of structure strength, anti-shock appearance and anti-drop. Shock tester is one of destructive experiments, and do destructive test on the product to evaluate the product reliability and monitor the consistency of production line.
-
product
STAMINA High-Speed Multi-Camera Recording
Stamina combines advanced hardware with easy to use software to offer a complete multi-camera recording solution for your imaging challenges. With the complete imaging system it becomes possible to record, view and combine up to 9 cameras in one setup. Our software is compatible with a wide range of cameras, providing the option to integrate your own cameras into the imaging setup easily.With Stamina, all recordings can be synchronised and all image data is directly streamed to the solid storage, enabling longterm streaming. With the external Application Programming Interface (API), Stamina can be further customised and integrated in your existing setup. Through the API, you have access to device settings, recording parameters and image data.Stamina is a completely customizable multi-camera recording and imaging solution. Our experienced sales engineers will advise you on the right system for your application.
-
product
NI-5772, 1.6 GS/s, 12-Bit, 2.27 GHz Bandwidth, 2-Channel Digitizer Adapter Module for FlexRIO
782097-02
The NI‑5772 is a digitizer adapter module that, when combined with a PXI FPGA Module or Controller for FlexRIO, creates a high-speed digitizer that can simultaneously sample two channels at 800 MS/s or sample one channel at 1.6 GS/s with over 2 GHz of analog bandwidth. You can use the NI‑5772 to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
