Fixtures
orient and afix UUT.
See Also: Fixturing, Test Fixtures, Mechanical Fixtures, Vacuum Fixtures, Jigs
-
Product
Spectrum Analysis, Up To 13.5 GHz
S930901B
-
The S930901B spectrum analysis adds high-performance microwave spectrum analysis to the PNA family up to 13.5 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Simultaneous spectrum measurements can be done using up to five test and reference receivers. This multi-channel SA can be used with the internal swept-signal generators for efficient measurements of spurious signals emanating from mixers and frequency converters. The SA application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy.
-
Product
Stand-Alone Test Fixture
MA 2012/D/H/GR2270/71
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,00 kg
-
Product
Manual Fixture Kit
230355 – CMK-06
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Universal Test Fixture
CAM/GATE
-
The Low Cost Solution for Accurate and Dependable Universal Functional TestThe CAM/GATE ® Universal Test Fixture System is your afforable, efficient solution for functional test. No need to have multiple fixtures in your test area...
-
Product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 335 x 250 mm (wxd)
CMCSK-02-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
FEA and Strain Gauge Testing
-
Circuit Check began Strain Gauge Testing in 1999 when BGA/SMT technology started replacing PTH components, reducing strain levels was a reactive post fixture fabrication process. We quickly recognized that the “reactionary” process was neither efficient nor were we capable on knowing the lowest achievable strain levels. Our engineering team came up with visual tools utilized during design to easily identify areas of excessive probe force, though still not enough data was generated to identify the lowest possible strain. Finite Element Analysis software models the PCBA and test fixture and applies the pressures from test probes and board supports and indicates the micro strain level applied to the PCBA. Using the FEA software during our design process allows our engineers to modify fixture designs to attain the lowest possible micro strain before fabrication begins.
-
Product
PCB Test Fixtures
-
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
Product
Design for Test
-
Test Coach offers Design for Test (DFT) consulting to assist customers with design review of prototype boards prior to release for production. Design for Test analysis is extremely important in ensuring that an assembly will achieve the highest possible test coverage. For ICT, this DFT will review the board to confirm that the bed-of-nails test fixture can be fabricated to test an assembly without sacrificing test coverage. As with ICT, Flying Probe benefits from DFT analysis by reviewing test point access and mechanical challenges that may affect the potential test coverage. Completing a DFT enables Test Coach to make recommendations to our customers that may be implemented on boards during the design phase which will allow for the most comprehensive coverage at time of test.
-
Product
Basic Threaded Probes F731
-
A contact probe or sensor featuring a screw thread on its body that firmly screws into a corresponding receptacle, fixture, or process port.
-
Product
Solid Oxide and Molten Carbonate Fuel Cell Test Stations
-
Greenlight''s SOFC test systems include options for integrated reformers, de-sox, gas mixing, water saturation, pre-heating, furnace, heat recovery and water balance. These SOFC test rigs can be configured to operate on gaseous or liquid fuels, with operating temperatures up to 1000C. Pressure control is optional and furnaces can be tailored for either planar or tubular cell configurations. For single cell or button cell testing, Greenlight offers the X20 table-top SOFC test bench, including furnace and optional fixtures.
-
Product
New Generation Vacuum Box for the 3070 Test Platform
Vortex Series
-
The Vortex Series is a new generation vacuum box for the 3070 test platform that will easily revolutionize in-circuit test. The simplified and streamlined design allows for maximizing the usable testable board size of the Vortex 100 Performance Grade fixture. The rugged all aluminum design maximizes the opening angle of 85° ideal for Cobot usage, while eliminating the top plate and associated hardware and retaining our classic quick plate guided probe technology.
-
Product
Air Data Adapter Test Panel
TA-241
-
AZ-241 Adapter Panel is designed to meet manufacturer's requirements. This panel will allow by the book testing of the air data computer when interfaced with the main air data test fixture. The Scott-T transformer is optional or can be customer supplied. Without the Scott-T your API can read the altimeter resolver directly.
-
Product
IP-B-F-SB-085-LA-085-01
1016626
-
The IP-B-F-SB-085-LA-085-01 is a high-performance component designed for use in Interface Solutions, particularly tailored for ICT fixtures. This model boasts a robust design featuring solder connections, ensuring reliable and durable performance. With a continuous current rating of 15.00A, it supports various electrical requirements, making it suitable for a range of applications within the ICT industry. The use of premium materials, including brass for both the plunger and tip style, enhances the component's longevity and operational efficiency. The gold plating provides additional corrosion resistance, a crucial feature in environments subject to moisture or other corrosive elements.
-
Product
LCR Measurement
-
LCR component bridge with built-in test fixture and limits comparator with binning. Micro-ohmmeter with four terminal Kelvin clip leads. High basic accuracy, rechargeable battery operation.
-
Product
MCB Thermal Trip Calibration Test Bench (IEC 60898 Cl 9.10.1.2, Annex I.1, IS)
-
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.
-
Product
Test Adapters
-
In our specially developed MG range of linear test adapters (test fixtures), we use solid aluminium components in our mechanical construction. This is to ensure the reliability and contact accuracy of the test adapter.
-
Product
Flexible Arm 200
INO006031
-
With our MECHANICS kit, you have your fixtures, test specimens, and setups firmly under control. The numerous user-friendly components work perfectly with your SMARTTESTER® testing system. The identical connecting technology and tools allow the individual parts to fit seamlessly together. Thus, your testing scenarios can be realized in record time and adjusted super fast. Flexible arm with central clamping. Holding force approx. 16 N. Extended length approx. 432 mm.
-
Product
MMI-CI
100694
-
For fixtures with higher voltages, the MMI-CI is a good basis. The MMI-CI is made of NON-dissipative plate material and can therefore be used in the low-voltage range (up to 1000V AC/ 1500V DC). The earthing package included is an important component. This is because the housing earthing, the earthing connection and also the earthing test ensure that the safety standards are met. The solenoid interlock and the safety switch ensure access protection.
-
Product
IB-R-SB-170-4A-WW-03-FL
1163960
-
The IB-R-SB-170-4A-WW-03-FL from Interface Solutions represents a specialized block designed for ICT fixtures. With a temperature range of -45°C to +100°C, this block is adept at handling diverse environmental conditions, ensuring reliable operation in critical applications. Its design showcases durability and precision, particularly due to its use of high-quality materials such as beryllium copper for the tip and plunger, which provide excellent conductivity and resistance to wear, thus enhancing the overall longevity of the product.
-
Product
ATE Test Probes
-
For contacting loaded PCBs in automatic test equipment (ATE) with vacuum, pneumatic or mechanically operated fixtures. Available in 2.54mm, 1.91mm & 1.27mm test centre spacings.
-
Product
Receiver, 9025TR, 25 Module, with 20" Platform
310104435
Receiver
Runners along the platform provide a smooth-sliding action, ideal when using fixtures up to 180 pounds. The 9025TR can be adapted to accommodate vacuum or mechanical fixturing. VPC modules can be intermixed to establish flexible custom interfaces which are ideal for functional and system testing applications. The 9025TR uses all standard VPC 90 series modules and contacts, includes a microswitch and is available with optional table legs and keyboard tray kit. Slide kit required, but not included.
-
Product
PCIe
M.2 Gen4 Socket3
-
SCHILLER AUTOMATION GmbH & Co. KG
The PCIe Gen4 M.2 Socket 3 test adapter or test fixture kit facilitates Device and Host compliance testing for PCIe Gen4 M.2 Socket 3 Source and Sink devices.
-
Product
Actuation Methods for In-Circuit Test Fixtures
-
Commonly referred to as In-Circuit Test (ICT), loaded board test can be defined as the task of measuring values of components that have been installed on a printed circuit board (PCB). A second basic category of loaded board test measures simple open and shorts on the board to verify manufacturability standards. Circuit Check supports all forms of in-circuit test strategies with its Performance Grade and Value Line test fixtures.
-
Product
Universal Testing Systems
-
Instron universal testing systems are versatile, high-accuracy platforms (available in electromechanical and hydraulic variants) designed to perform a wide range of static mechanical tests, such as tension, compression, bend, peel, shear, puncture, and more, on virtually any material. They support force capacities from fractions of a newton up to thousands of kilonewtons, with precision load measurement, high data acquisition rates, and compatibility with thousands of accessories, including a wide range of extensometers, grips, fixturing, and automation solutions to meet demanding quality and throughput standards.
-
Product
S-Beam Static Load Cells
2519 Series
-
The 2519-xxxN Series load cells are specifically designed for use with 3300 single column testing systems. Automatic transducer recognition and electrical calibration makes them easy to use. The load cells incorporate overload protection and can withstand loads up to 150% of their force capacity without damage and 300% without mechanical failure. The load cells allow the user to zero out the tare weight of a grip or fixture that weighs up to 40% of the force capacity, while still maintaining the full specified accuracy.
-
Product
Cost-Effective ATE System
PRO RACK ATE
-
Qmax Test Technologies Pvt. Ltd.
Pro-Rack is a cost effective ATE System, which comes with Modular Structure provision option to improvise and enhance much instrumentation based on the user’s requirements. Basically it is designed to cater to the needs of PCB test and repair depots, keeping in mind the changing PCB technology and the challenges in testing them off-line. It can provide complete PCB test and diagnostic functions for any kind of PCB including the latest very high density complex PCBs with high pin count PQFP, FPGA VLSI chips. AC /DC parametric tests enables testing of the DC parametric of device pins on the edge connector for input bias current, Fan out capacity ,Tri-state leakage currents, AC parametric measurements such as Input / Output Propagation delay Rise time / Fall time to further enhance fault coverage. Pro-Rack is designed with VPC Mass Interconnect adapter with 16 bit fixture ID interface to the UUT through simple clips and probes or through card edge or through a bed of nail test fixture.
-
Product
A Popular Combination Of Flex 10 And Flex 20 In A Compact Footprint
Flex 30 ATE
-
A combination of both the Flex 10 and 20 system, the Flex 30 is floor mounted system that maintains a small footprint whilst offering that useful additional space. Generally it is fitted with either the G12 or G12X VPC interface allowing a large number of mixed signal connections to be routed to the test fixture.
-
Product
EAOC, Electric Servo Drive
-
The AOC-E module is an electric servo drive for the automated opening, closing and contacting of mechanical or vacuum test fixtures, aimed at optimizing work processes and increasing productivity.
-
Product
MMI-HV, Mechanical Test Fixture
100182
-
Mechanical test fixture with optimized ergonomics for function test, final test and ICT applications. The MMI is prepared for both safety switches with guard locking and electrical interlocking. Our test fixture is versatile.
-
Product
Stand-Alone Test Fixture
MA 2011/D/H
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1000Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 12,00 kg
