-
product
SMARC V1.0 SoM With IMX6 Quad/DualLite 800 MHz (Industrial) SoC, 1GB RAM, 4GB EMMC, GbE LAN, Audio, CAN, MIPI And PCAM
SCM120
*SMARC 1.0 (82 x 50 mm)*Ultra low power consumption Cortex™-A9*2 CAN 2.0B*24-bit TTL signal*LVDS/HDMI 1080P*10/100/1000 Mbps Ethernet*Linux3.0.35/Android 4.3*Audio
-
product
Operation Support System for Wafer Prober
N-PAF
N-PAF (Network-Based Prober Advanced Function) is a networking system developed for more effective operation and maintenance of multiple wafer probers. Remote operation helps save on labor on the factory floor. An E10-compliant RAM Analyzer can be used for operation management of the system
-
product
External Controller for PXI
External Controllers for PXI are rack-mount controllers that feature high-performance multicore processors, up to 4 GB of dual-channel DDR2 RAM, and optional RAID hard-drive configurations for high-speed streaming to disk. These devices offer hot-swappable fans and options for redundant power supplies. The External Controller for PXI is designed for mission-critical, physically demanding applications.
-
product
16 SE Or 8 Diff. Input Channels, 4 Analog Output Channels, PCI Express
APCIE-3121-16-4
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
CPCI ARM LPC3250 Board
MS 1513
- 32 Bit ARM LPC3250 Processor (256KB SRAM)- 133MHz External Bus Speed and 266 MHz internal CPU Speed- 32 Bit, 33MHz CPCI Bus, 6U Form Factor- External memory ( Flash – 2 MB, RAM - 512 KB, DPRAM – 128KB)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 2 RS232 Serial Ports, 4 RS422 Serial Ports- M Module Interface- 6U board compatible with CPCI & PXI backplanes- High Speed Logic Device- Hot Swap Feature- Front Panel and Rear IO Interface- External Bus through Rear IO- Reception of 3Kbytes within 2ms through Ethernet- Board Dimension is 160mm x 233.35mm- Power Requirements: +3.3V, +5V and +/-12V- Board Dimension is 160mm x 233.35mm- Board has Rear IO interface- Ethernet, JTAG, RS232, USB connectors at front side- BSPs and Driver software for Windows and Linux OS
-
product
PCMCIA Card
DAS-429PCMCIA/RT10
Both cards contain 68 Kbytes of true dual-port RAM, for data blocks, control registers and Look-up table, mapped within the Common Memory space. The card also contains a FLASH-based Card Information Structure (CIS) within the Attribute Memory space.The cards comply with the Personal Computer Memory Card International Association (PCMCIA Release 2.1) standard, including Plug and Play. The card's small size and suitability for PCMCIA compatible notebook computers with Type II and Type III slots make it a complete solution for developing and testing ARINC-429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The cards are supplied with C drivers, including source code, Mystic Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
product
Low-power, High-performance FPGA
iCE40 LP/HX
*Available in three series with LUTs ranging from 384 to 7680: Low power (LP) and high performance (HX)*Integrated hard I2C and SPI cores that enable flexible device configuration through SPI*Match your preferred display to your application processor with interfaces such as RGB, 7:1 LVDS and MIPI DPI/DBI*Multi-source your image sensors by implementing flexible bridges supporting common interfaces such as HiSPi, subLVDS, LVDS and Parallel LVCMOS*Up to 128 kbits sysMEM™ Embedded Block RAM*Industry’s broadest range of 0.35 mm - 0.40 mm pitch BGAs fit in space-constrained applications
-
product
Get Flexible, Get FlexiFLASH
LatticeXP2
*Up to 885 Kbits sysMEM™ embedded block RAM and up to 83 Kbits distributed RAM*sysCLOCK™ PLLs up to four analog PLLs per device that enable clock multiply, divide and phase shifting*Three to eight sysDSP blocks for high performance multiply and accumulate.*Pre-engineered source synchronous IOs for DDR/DDR2 up to 200 MHz and 7:1 LVDS interface support up to 600 Mbps*Available in csBGA, TQFP, PQFP and BGA packaging
-
product
3.5" Embedded SBC With Intel® Celeron® J1900 Processor, LVDS/VGA/HDMI, Dual LANs, Audio And ZIO
CAPA843
The CAPA843, a fanless 3.5-inch embedded board, features quad-core Intel® Celeron® processor J1900 SoC (codename: Bay Trail). A pair of SO-DIMM sockets supports up to 8GB of DDR3L 1066/1333MHz RAM. The compact size embedded board CAPA843 was designed with emphasis on expandability, offering two full-size PCI Express Mini Card slots, as well as an exclusive Axiomtek ZIO connector. With excellent thermal design, the 146 x 102mm embedded SBC can handle operating temperatures from -20°C to 70°C, and runs on +10V to +24V DC input. The 3.5” fanless embedded board provides three display interfaces with dual-display operation: HDMI, LVDS and VGA. The Axiomtek CAPA843 is an excellent choice for applications in IoT/M2M-related, industrial control, self-serve terminal, gaming, digital signage, POS, and kiosk.
-
product
8 SE Or 4 Diff. Input Channels, 4 Analog Output Channels, PCI Express
APCIE-3121-8-4
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
Intelligent Interface Card
IIB-1553-PCI-2C
The IIB-1553-PCI-2C provides an intelligent interface card for two serial, dual redundant MIL-STD-1553 data buses and the PCI bus. The card supports 1553A, 1553B, McAir and STANAG 3838 variants on a single card. The IIB-1553-PCI-2C provides concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. Two independent variable amplitude dual redundant 1553 interfaces are provided, each with2 Mbytes of dual ported RAM. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
product
Direct Digital Synthesis (DDS)
Analog Devices’ world leading direct digital synthesis ICs incorporate features such as on-board comparators, RAM, PLLs, mixers, and registers. This makes them an ideal agile frequency synthesizer solution in systems for communications, test equipment, and radar.
-
product
16-bit, 200KHz, 4SE/2DIFF Isolated Analog Input Board
APCI-3016-4
The APCI-3016 is a 16-bit analog input board for 3.3 V and 5 V PCI systems, with optical isolation and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.
-
product
Memory
Renesas offers MIL-STD-883-compliant CMOS random access memory (RAM) and CMOS programmable read-only memory (PROM) devices that are that are qualified to QML Class Q military standards.
-
product
Fiber Channel Simulyzer
Avionic Interface Fiber Channel SimulyzerTM products are multifunctional, high-performance Fiber Channel interface and test boards. The products have both a data generation / simulation function and a monitor / analysis function on one board. Avionic Interface Fiber Channel products can be used with the most popular upper layer protocols FC-AE-ASM, FC-AE-1553, FC-AE-RDMA and FC-AE-AV. All FibreChannel products use multiple processors with large onboard RAM.
-
product
Fibre Channel Simulyzer™ Products
Avionics Interface Technologies
Our Fibre Channel products support most popular avionics Upper Layer protocols including FC-AE-ASM, FC-AE-1553, FC-AE-RDMA and FC-AE-AV. All AIT Fibre Channel modules utilize multiple processors with large onboard RAM. An onboard processor runs the driver software, minimizing host CPU interaction, enabling autonomous operation with minimal interaction during time-critical applications.The Fibre Channel products use our Simulyzer™ technology that enables the hardware to simultaneously perform Fibre Channel data generation and Fibre Channel monitoring on the same physical board. The Fibre Channel test products include full-function device driver software for the most popular operating systems, an application interface supporting development environments, as well as a comprehensive set of source code examples.
-
product
16-bit, 100KHz, 8SE/4DIFF A/D Inputs; 4 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, all isolated
CPCI-3120-8-4
Input range:- ± 10 V, 0-10 V software programmable- 0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V,- ± 1 V (gain)- 0-20 mA (option)- software-programmable amplifier:- PGA x1, x2, x5, x10- Conversion triggered through software,scan, timer, external event- Onboard FIFO buffering for 256 analog values- Data exchange through 16-bit I/O or 32-bit memory (PCI DMA)- Sequence RAM- Overvoltage protection- input filter: 160 kHz
-
product
RightMark Memory Analyzer
RMMA
Before this test packet was created there was no proper software for measuring vital system parameters such as CPU/Chipset/RAM providing steady and reliable (reproducible) test results and allowing for changing test parameters in a wide range. Vital low-level system characteristics include latency and real RAM bandwidth, average/minimal latency of different cache levels and its associativity, real L1-L2 cache bandwidth and TLB levels specs. Besides, these aspects are usually not paid sufficient attention in product technical documentation (CPU or chipset). Such test suite, which combines a good deal of subsets aimed at measuring objective system characteristics, is a must have for estimating crucial objective platform parameters.
-
product
Bridging And I/O Expansion Versatility. Rapid Hardware Acceleration For Improved Signal Control.
MachXO2
*Up to 256 kbits of user Flash memory and up to 240 kbits sysMEM™ embedded block RAM*Up to 334 hot-socketable IOs that avoid excess leakage*Programmable through JTAG, SPI, I2C or Wishbone*TransFR feature allows in-field design update without interrupting equipment operation*Programmable sysIO™ buffer supports LVCMOS, LVTTL, PCI, LVDS, BLVDS, MLVDS, RSDS, LVPECL, SSTL, HSTL and more
-
product
Real Time Switch
IM1754G
Real Time Switch is a real time timer which can be used to switch electrical appliances like street lamps, garden lights, corridor lights, neon signs etc as per time of the day. The timer has built in almanac timings fixed in nonvolatile ram so that the user does not have to programme the unit from time to time. This has added advantage over daily dial or weekly timers. Timer provides two outputs to drive contractors of different ratings. These outputs can be used with different combinations to achieve desired output. Timer is provided with manual override facility. Optional detachable external keyboard unit provided to avoid unauthorized access.
-
product
PXI Digital Pattern Instrument
The PXI Digital Pattern Instrument is designed for semiconductor characterization and production test. It provides 32 channels, a voltage range of -2 V to 6 V, a PPMU force voltage range of -2 V to 7 V, up to a 200 Mb/s data rate, and a clock generation rate up to 160 MHz. The module includes Digital Pattern Editor software as well as debugging tools like shmoo, digital scope, viewers for history RAM, pin states, and system status.
-
product
ARINC 429 Test And Simulation PCIe Module
PCIe-C429
*4, 8, 16 or 32 software programmable TX / RX channels*X4 lane PCI Express host interface*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
Battery Backup IC
Analog Devices offers a range of supervisory circuits that offer a complete single chip solution for power supply monitoring and battery control functions in microprocessor systems. Functions include microprocessor reset, backup battery switchover, watchdog timers, CMOS RAM write protection, and power failure warning.
-
product
Intel 80486 DX2 Processor Board
MS 1500
- PC 104 bus and ISA bus interface- Facilitates design of scalable architectural solution for Embedded System- Back plane eliminated by self-stacking PC 104 bus- Substantial reduction of development time, cost, as well as risk- Helps to Faster time-to-market / timely product productions- Used for LCA Simulation Project- Intel 80486DX2 @ 33MHz- 512Kbytes of STATIC RAM, 2048 Kbytes of FLASH PROMS- 64 Kbytes of DPRAM- External Interrupts- RS232 Serial Interface- Watchdog Timer- External Bus Interface
-
product
PCI Express Ultra-fast Data Acquisition Add-In Cards
Ultraview's PCIe series of data acquisition add-in cards are complete A/D systems on a single PCIe add-in card. These boards incorporate up to 8GB of on-board RAM with up to 7GB/sec on Kintex 7 (up to 1.4GB/sec on Virtex 5) typical PCIe bus transfer rates enabling full-rate acquisition for long durations. All boards in the PCIe series are supported with the same user software allowing users to select the bit resolution and acquisition rate appropriate for a given application and then easily re-use the same software on a different part. Included with each card are graphical waveform viewers, example user software with source code included, and device drivers for Linux and Windows. The example software is intended to allow users to quickly prototype and develop their applications.
-
product
PCIe FPGA Carrier For FMC+, Kintex UltraScale™
PCI592
The PCI592 is based on the Xilinx XCKU115 Kintex UltraScale FPGA, which provides 5,520 DSP slices, 75.9 Mb RAM and 1,451,000 logic cells. The FPGA interfaces directly to the FMC+ DP-23 and all FMC+ LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to three DDR4 memory channels (2x 64-bit wide and 1x 32-bit wide). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host. The unit has x8 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. In addition, 16 uncommitted connection pairs are routed to a dual x8 expansion connector, providing direct connectivity to a neighbouring FPGA (e.g. via Aurora, 10G/40G, SRIO, PCIe) without the need to go through the host.
-
product
Acute 4GS/s 136 Channel Logic Analyzer With 32Gb Memory
Acute LA3136E+
*LA3000E+/B+ series logic analyzer*PC-based*68 / 136 channels*USB 3.0 interface, 12V power adaptor*4GHz Timing Analysis / 250MHz State Analysis*32Gb RAM
-
product
Fibre Channel Modules
AIM’s Fibre Channel test, simulation and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with one dual core RISC processor per port, massive and scalable DDR3 memory and IRIG-B time encoder/decoder functions are standard. The new ultra high performance intelligent 4-lane PCIe 2.0 interface modules offer 2 ports with full function test, simulation, monitoring and analyzer functions for Fibre Channel networks. The dual core processor provides onboard processing and data transfer capabilities for the most demanding Fibre Channel applications including upper layer protocol support done on board level. Large and high data throughput DDR3 RAM is accessible for the onboard processor as is a high performance FPGA implementing the customized Fibre Channel interfaces enabling the board to analyze incoming and modify outgoing data in real time. Each module provides 2 Fibre Channel compliant full duplex ports, implementing the full link level services. SFP cages make it suitable for different media types as optical or electrical network technologies. Ports operate either in Traffic Simulator or Analyzer/Monitor mode with support for port related Frame Statistics. Sophisticated packet capturing mechanism and monitoring features are complimented with powerful triggering and filtering capabilities.
-
product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PC104p-429
*4 or 8 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*128 MB RAM*Label selective triggering for recording / filtering*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
RMC-8357, 2.1 GHz, 1U Rugged Rack-Mount External Controller for PXI
785673-01
2.1 GHz, 1U Rugged Rack-Mount External Controller for PXI—The RMC‑8357 is a rugged 1U rack-mount controller for PXI- or PXI Express-based systems intended for test and measurement applications requiring rack-mount controllers. It features up to two Intel Xeon eight‐core processors that support up to 32 GB of RAM. The RMC‑8357 offers hot-swappable fans, options for redundant power supplies, and support for RAID arrays, which allows multiple hard drives to be configured for high performance for mission‐critical, physically demanding applications. The RMC‑8357 meets the PXI standard’s mechanical shock and vibration specifications and functions over wide operating ranges.





























