Pressure Calibrators
Provide precision simulation of known values to ascertain pressure instrument graduation deviation.
-
-
product
Portable Calibration System
HD9120
HD9120 is an acoustic calibrator that, in accordance with the Circular Prot. RU 34143 of 02 December 2011, allows qualified technicians to perform calibrations of sound level meters for comparison with a reference sound level meter.
-
product
Intrinsically Safe Calibrators
We offer calibrators that are Intrinsically Safe and can be used in hazardous Ex areas, where explosive gases may be present. Using Ex certified calibrators makes it easier for you, as it eliminates the need for always getting hot-work permits when going on site. Our Ex calibrators are both ATEX and IECEx certified.
-
product
Pressure Senders & Temperature Probes
UMA makes a complete line of temperature probes included solid state types. For engine monitoring, we have probes made of brass with thread sized from 1/4-28 to 5/8-18 and various metric sizes, as well as in many different lengths.
-
product
Phase Noise Generator / Calibrator
PNG-A
Noise eXtended Technologies S.A.S.
The PNG-A is a high precision generator used in Test and Measurement instruments calibration. It is a Signal Generator with precisely computed phase and amplitude noise characteristics. With its wide frequency offset range, 1Hz to 1 MHz offset, and its programmable Phase and Amplitude noise in real time, this is the ideal standard to calibrate phase noise analyzers, Signal Source Analyzers and Spectrum Analyzers.
-
product
CT/PT Calibrator
HEY-H / 605
Wuhan Huatian Electric Power Automation Co., Ltd.
Intelligent instrument calibrator for PT CT error and impedance admittance test.
-
product
Pressure Switches
INELTA Sensorsysteme GmbH & Co. KG
The mechanical pressure switch is available in steel or brass housing design and offers this special features:* robust and low cost* different adjustable rangesup to 50 bar* different pressure fittings* switched voltage up to 48 VDC* kind of contact: norm open, norm closedn flat connector 6,3 x 0,8 mm* cycles of pressure up to 106
-
product
Digital Pressure Meter
DPM-2300
The DPM-2300 series is a Microprocessor based high precision, high resolution digital pressure meter. These meters measure both gas and liquid pressures and provide multiple engineering unit displays for the results.
-
-
product
Network Analyzer N-Port Calibrated Measurements
S93551B
The S93551B adds a multiport analyzer mode that enables full N-port error correction and measurement capabilities using an external test set.
-
product
Temperature and Pressure
Encore Electronics manufactures a complete line of rugged and economical instrumentation for temperature and pressure measurement. Our standard, in-stock units can be used for pressure measurement depending on the signal level and output required. Our equipment is available in both DIN rail and modular/rack-mounted configurations for multiple channel capability. Simply specify your output — whether 4 to 20mA , 0 to 10V, or a custom output and Encore can configure a system to match your needs. Whether you need isolated input and outputs using transducer power or computer-controlled units, we will design and build a unit to meet your requirement.
-
product
6GHz SMA Calibration Kits
CAL-SMA-6F
The CAL-SMA-6F Full calibration kit provides all elements for Male and Female Open-Short-Load and Through calibrations for one and two port VNA measurements.
-
product
Pressure Controllers & Transducers
Alicat Scientific, Incorporated
Fast pressure controllers keep your process stable and repeatable. Alicat offers pressure controllers for use in flowing, dead-ended, or vacuum applications. Dual-valve models for closed volumes eliminate the need to continuously bleed expensive process gases. Instruments are available with absolute, gauge, or differential pressure sensors for pressure control as high as 3000 PSIA/PSIG (or 150 PSID) and as low as 2 inH₂O.
-
product
Evaluation Kit for Differential Pressure Sensors of the SDP3x Series
EK-P4
The evaluation kit EK-P4 is designed for an easy and cost-efficient evaluation and qualification of Sensirion's SDP3x differential pressure sensors. Test now the features of the new differential pressure sensor. Especially at lowest pressure differences, the sensor provides highest accuracy and long-term stability. The evaluation kit EK-P4 is designed for an easy and cost-efficient evaluation and qualification of Sensirion's SDP3x differential pressure sensors. Test now the features of the new differential pressure sensor. Especially at lowest pressure differences, the sensor provides highest accuracy and long-term stability. The evaluation kit consists of a USB stick connected to a PCB on which an SDP3x differential pressure sensor is already attached. The included flow element can be easily affixed to the kit with two screws and then directly connected to the gas flow. Detailed information about the flow element can be found in the application note.
-
product
Oscilloscope, Calibrated, 2 Channel, 100 MHz, 1 GSPS, 25 kpts, 3.5 ns
72-8710A CAL
The 72-8710A CAL from Tenma is a digital storage oscilloscope with 100MHz bandwidth, 2 analogue channels. The digital storage oscilloscope provides a complete set of trigger modes including edge, pulse, alternate and storage modes including set-up, wave, bitmap. It has a 7 inches wide screen LCD display and supports plug and play USB storage device. Communication with and remote control of computer through the USB device.
-
product
Volume Calibration
Trescal provides full Volume Calibration services that are accredited and/or certified in accordance with ISO/IEC 17025. Volume Calibration services can be delivered at your site or at our lab. Accreditations for our volume calibration service guarantees calibration results are traceable to the International Systems of units (SI) through NIST or NRC.
-
product
Combined Pressure and Temperature Transducers
We can offer some different styles of Combined Pressure and Temperature Transducers. The EPTT5100 combined pressure and temperature transducer has an internal temperature sensor. The miniature EPTTE1400 combined pressure and temperature transducer has an external temperature probe.
-
product
Automatic Transmission & Engine Oil Pressure Tester with 2 Gages
34580
Check oil pressure in automotive transmissions and engines. Adapters provide coverage of most domestic and imported cars and light trucks. Includes two gages: Large Gage calibrated from 1-600 PSI (0-4,000 kPa & 0-7.0 BAR) and Small Gage for lower pressure requirement 0-50 PSI (0-3.5 BAR) Large gage can be used for all applications and has hang-up hook. Small gage is for more accurate reading of engine oil pressure where maximum oil pressure does not exceed 50 PSI (3.5 BAR). Includes 6 feet of oil proof hose and 10 assorted fittings. Supplied with instructions in a molded plastic case.
-
product
Digital Gauge Pressure
ZET 7012-I VER.3
Digital gauge pressure ZET 7012-I VER.3 (open membrane) is used for fast and simple overpressure measurements and measured values data transfer in digital format via RS-485 or 4-20 mA interface. ZET 7012-I VER3 digital gauge pressure meter is intended for integration into various technological processes automated control systems. Open membrane type enables sensors operation in viscous, pasty and rapidly polymerizing environments.
-
product
Calibrator Process
VA70034
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Loop calibrator This Calibrator is use to measure or output 0 to 24 mA DC current loop, and 0 to 20 V DC voltage.
-
product
Light / Lux Meter, Calibrated, 50000 lx, 100 lx, 4 %, 185 mm, 78 mm, 38 mm
72-7250 CAL
The 72-7250 CAL from Tenma is a digital light meter with RS232 capability. It has custom one-chip microprocessor LSI circuit which ensures high accuracy. The meter features 13mm (0.5”) super large LCD display with contrast adjustment for best viewing angle, data hold and auto power off. It records maximum, minimum and average readings with RECALL facility. The 72-7250 has RS-232 PC serial interface, user selectable lighting type (tungsten, fluorescent, sodium or mercury, daylight) and zero adjustment by push button. The meter operates from 9V battery.
-
product
Ice Point Calibrators
These ice point calibrators are designed to accurately calibrate probes at the freezing point of water. These devices have multiple thermowells to calibrate multiple sensors simultaneously.
-
product
Pressure Gauges
All of our pressure gauges are controlled by micro processors to guarantee the highest accuracy. They determine absolute pressure, negative pressure or differential pressure in air and liquids devices perfect for a research and development environment. At PCE, you can find a high-quality pressure gauge which is suitable for extreme operating environments and meets the highest industry standards. They can even be used in small places, little holes, tubes or pipes. Some pressure gauge series have the capability to transfer data to a computer, a printer or a storage device.
-
-
product
Sound Level Meters and Calibration
PeakTech Prüf- und Messtechnik GmbH
This digital sound level meter is designed for noise projects, quality control and all kinds of measurements of ambient sound, as well as for sound measurement in factories, schools, offices, in traffic , Household and much more used.
-
product
Calibration Systems
Brüel & Kjær Sound & Vibration A/S
Our calibration solutions meet the broad variety of needs for calibration in the field of sound and vibration accurate primary and secondary calibration of measuring equipment and the scope of transducers: accelerometers, microphones and hydrophones.
-
product
Miniature Pressure Sensor
Series 2 Mi
KELLER AG für Druckmesstechnik
Developed for measuring hydrodynamic and aerodynamic pressures. A silicone drum protects the measurement cell from the influence of vibrations and fast acceleration.
-
product
Back Pressure Tester
TU29P
Enables Technician to test exhaust back pressure thru oxygen sensor. Oxygen Sensor adapter includes M12 & M18 thread.Special Gauge has two multi-colored bands - idle and 2500RPM, with pressures shown in PSA and bar.
-
product
Pressure Decay Test Systems
Pressure decay leak testing technology has become a mainstay in the arena of high volume production testing. Pressure decay testing methods offer the world's manufacturers a cost-effective and easily applicable solution to the leak testing challenges they encounter on a given day. Fundamentally, pressure decay testing is a straightforward measurement technique; Cincinnati Test Systems (CTS) pioneers new and innovative ways to integrate our technology into custom turnkey systems that exceed the industry standards for reliability and repeatability. CTS' 30+ years of experience goes way beyond the pressure test unit by offering our customers comprehensive, custom turnkey solutions to the most challenging leak testing problems.
-
product
Diaphragm Operated Pressure Switch
SA1100
Extremely rugged construction assures excellent reliability in chemical, petroleum and industrial plants. New design also provides burst pressure protection to 3000 psi (206 bar). The rolling diaphragm design maintains a constant effective area to minimize friction.
