Dynamic Signal
digital processing FFT to reveal properties of a signal.
-
product
8 Channel Relay Board for Signal Isolation
FXA-104 Relay 8CH
The FXA-104 is a relay board to switch signals with 8 SPDT channels. It’s eight channels can be switched individually with a low active input. Each channel is equipped with a status led and capable of switching up to 2A. Due to its wide range input it’s very flexible to use and it is delivered with an installed DIN rail carrier.
-
product
Dynamic Particle Image Analysis System
iSpect DIA-10
Shimadzu's iSpect DIA-10 Dynamic Image Analyzer combines particle size and image analysis technology to offer complete particle characterization. It can perform particle imaging, size analysis, and foreign object detection, and obtain size distributions and number concentration, in as little as two minutes.
-
product
Signal Analysis
Cross-Spectrum FFT Analysis
The program Cross narrow-band spectrum is used for evaluation of the interrelation between the signals’ parameters obtained from the two primary transducers installed at various parts of the controlled object. This program can be used for detection of noise source location, for sound absorption level evaluation and the researched object acoustic properties control, for evaluation of space-time distribution of the directional energy flux (Poynting vector), for the ground cross-section FR characteristic evaluation (Nakamura method), etc.
-
product
Video Signal Generator
MSPG-4600MT
MSPG-4600MT is basically supporting the Teletext and Closed Caption as multi broadcast for the D-TV (NTSC, PAL), as well as V-Chip (Violence Chip) function to block the violence and sex etc. bad program to protect a person under age through the regulation grade.
-
product
ELECTRIC BRAKE FORCE METER WITH DYNAMIC LOAD SIMULATION AND CIRCUIT TESTING
MDTT9107
*Tests truck-side brake controller output and all towing-lighting functions without a trailer*Displays real-time brake controller output gain and timing*Quickly troubleshoots electrical circuits and ground condition*For use with aftermarket and integrated brake controllers*Microprocessor controlled; simulates trailer brake loads*25' cable allows one-man, in-cab testing of brake controller and all truck-side tow circuits*Use to verify that the vehicle’s adaptive (speed/load sensitive) brake-controller output is functioning properly
-
product
10 MHz to 33 GHz LAN Wide Dynamic Range Average Power Sensor
L2053XA
The Keysight L2053XA is a fast, accurate and wide dynamic range 10 MHz – 33 GHz LAN average power sensor.
-
product
Digital Signal Processors
Powerful Field Programmable Gate Array (FPGA) based Digital Signal Processors (DSP) with large memory, fast PCIe and optical data interfaces (ODI)
-
product
Spectrum Analyzers (Signal Analyzers)
Choose from advanced benchtop, handheld, general purpose, and scalable modular sprectum analyzers (signal analyzers), all with the broadest set of application-specific software. Advance your RF spectrum analyzer to the next level, spectrum analysis (signal analysis) has never been this easy.
-
product
2-way Radio Signaling Test Software
Tone Generator
The new PC-based test software for RF communications engineers and technicians. Flexible, accurate code synthesizer for simulation and testing of 2-way radio systems, repeaters, remote control, ANI, Paging and more.No external hardware required.
-
product
Signal Graphic Analyzer
SGA
SGA is the new generation of Signal Graphic Analyzer QC Tool. With a new user-friendly graphical interface, it can now be installed in any computer to process and analyze signals by reading SEG-D files. Able to work in real-time or in standalone mode, SGA is now compatible with SEG-D files rev3.0 and rev2.1.
-
product
Scienlab Dynamic DC Emulator
SL104XA Series
The Scienlab Dynamic DC Emulator provides an all-in-one system for efficient and effective testing of the power electronic components in electric vehicles (EV) and electric vehicle supply equipment (EVSE).
-
product
Digital Signal Processing (DSP)
Abaco has an extensive track record in helping our customers turn sensor-acquired data into actionable information in the shortest time and at the lowest bandwidth in a broad range of digital and analog applications.
-
product
PXI 16x4 Signal Insertion and Monitor Matrix
40-525A-002
This is a PXI signal insertion and monitor matrix with switched pass thru connections on both X and Y axis. It is also available in a 34x4 format and can be used for signal insertion and monitoring purposes on connections between the UUT and test system.
-
product
Advanced Power System - Dynamic DC Power Supply, 40 V, 50 A, 2000 W
N7972A
The N7900 Series dynamic DC power supplies are designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.
-
product
10 MHz to 40 GHz LAN Wide Dynamic Range Average Power Sensor
L2054XA
The Keysight L2054XA is a fast, accurate and wide dynamic range 10 MHz – 40 GHz LAN average power sensor.
-
product
Signal Generator High-Frequency GSM AXIe
The hardware-software complex "High-frequency GSM signal generator AXIe" is designed to generate harmonic sinusoidal signals with analog modulation (AM, FM, PM, IM) or without modulation in the frequency range from DC to 10 GHz.
-
product
Advanced Power System: Dynamic DC Power Supply, 80 V, 25 A, 2000 W
N7974A
The N7974A is designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.
-
product
400MHz DDS Signal Generator
440A
The 440A generates a sinewave is via an RS232 serial interface. The frequency is accurate to 1.5ppm and can be locked to an external frequency reference. The phase can also be programmed with 14-bit resolution. It includes a Line Voltage AC Adapter and a CD containing windows software.
-
product
2-Channel 400MHz DDS Signal Generator
2940A
The 2940A is a two-channel 400MHz DDS Signal Generator that generates two independent sine wave output frequencies simultaneously from 200kHz to 400MHz in 1Hz steps. A Clock Generator configuration with ECL or LVDS clock outputs is also available. The 2940A is lockable to an external frequency standard or is used with its internal TCXO. Optional internal amplifiers and 60dB step attentators available. Set all parameters with front panel controls and LCD display or by computer using the RS232 serial interface. All settings can be saved into non-volatile EEPROM memory upon power down. Windows software included.
-
product
Automotive CVJ Dynamic Fatigue Test Chamber
Dongguan City Simplewell Technology Co. Ltd.
Automotive CVJ Dynamic Fatigue Test Chamber by Simplewell
-
product
Vector Signal Generators
Rohde & Schwarz leverages decades of test and measurement excellence to provide you with a wide portfolio of RF vector signal generators. Our solutions range from the top-performance models capable of handling the most demanding signal generation tasks to midrange models featuring remarkably good RF characteristics, as well as compact solutions.
-
product
Signal Conditioning and RF Distribution
CAES provides high performance signal conditioning and RF distribution solutions such as switch matrices for the EW, missile, radar, communications and space markets. Our custom designs offer high speed switching, low insertion loss, low harmonic level and excellent isolation.
-
product
0.25° Accuracy Full Attitude Surface Dynamic Motion Sensor
DMS-525
The DMS range of motion sensors is designed specifically for the motion measurement needs of the marine industry. Whether it is achieving IHO standard survey from any size of vessel, or providing safety critical monitoring of offshore platforms, large vessels, helicopter landing decks, cranes and positioning systems, the DMS provides accurate motion measurement in all sea conditions. Incorporating an enhanced external velocity and heading aiding algorithm for improved accuracy during dynamic manoeuvres, the solid state angular rate sensors offer reliability in the highest performing vertical reference units ever produced by TSS.
-
product
9kHz To 40GHz Signal Generators Module
Corech Microwave’s Ultra Wideband Signal Generators Module operates from 9kHz to 40GHz, featured with ultra wideband, CW/Pulse mode, ultra low noise of -105dBc/Hz@10kHz , low spurious and low consumption. They are very rugged and stable to be integrated in various systems.
-
product
Head Mount Signal Conditioners
Head mount signal conditioners are designed to mount in industrial protection heads for use with thermowells. The sensors are small sized and offered in a variety of input and transmission options.
-
product
Audio Signal Processors
Two balanced mic or line level inputs24-bit A/D convertersAdjustable input gainPhantom powerPhoenix-style terminal block connectors
-
product
Switch Path Manager Signal Routing Software
Our signal routing software, Switch Path Manager (SPM), simplifies signal routing through switching systems and speeds up the development of switching system software. Switch Path Manager supports our switching modules and the interconnection between them. Once a switching system model has been created, simply defining the endpoints that are required to be connected together can perform signal routing.
-
product
DIGITAL TV SIGNAL ANALYZER
1702/1703
The optimal signal analyzers to test and measure both analog/digital signals. Especially, these models give users the capacity to measure 'C/N' very easily and correctly, which are very important measurement factors for the TV broadcasting signal.
-
product
USB Signal Conditioning Products
Signal conditioning can include amplification, filtering, converting, range matching, isolation and any other processes required to make sensor output suitable for processing after conditioning. It is primarily utilized for data acquisition, in which sensor signals must be normalized and filtered to levels suitable for analog-to-digital conversion so they can be read by computerized devices.
-
product
Signal, Module, ID, CASS, QuadraPaddle, 800 Position
510114131
Signal, Module, ID, CASS, QuadraPaddle, 800 Position.Mating module is 510113138.
