Automatic Test Systems
execute test program sets automatically. Also known as: ATS
See Also: Automatic Test Equipment, ATE Integrators
-
Product
Automatic Air Purging Tank
MF-015
-
If the fuel passing through a flow detector has mixing of air, the flow rate cannot be measured correctly. The MF-015 is an automatic air purging tank that uses a precision float valve. When fluid enters the flow line, the air is automatically purged to the atmosphere.
-
Product
Swept Test System For Optical Components
-
measurement platform for optical components with a fastscan speed, high resolution and accuracy. The systemcombinesour tunable lasers, polarization controller, power meter and software.
-
Product
Portable System for High-Boltage Solid Dielectrics Testing
HVTS-70/50
-
Portable system HVTS-70/50 is designed for carrying out high-voltage withstand testing of cable insulation and other solid dielectrics with DC (rectified) voltage up to 70 kV and AC voltage up to 50 kV RMS at industrial frequency (f = 50 Hz).
-
Product
16-Station Testing System
-
The ElectroPuls 16-Station testing system performs high cycle fatigue testing on multiple samples simultaneously, with a fatigue-rated load cell included on each station. The fixture uses a carousel designed with high stiffness and low mass to enable high frequency testing and reduce test time.
-
-
Product
Materials Test Systems
-
An impedance analyzer is a device that uses a programmable AC voltage / current source, together with voltage and current measurement circuits, to characterize sample impedance over a wide range of frequency. An example of this being the world famous Solartron Analytical 1260A Impedance Analyzer that provides EIS impedance characterization over more than 12 decades of frequency from uHz to tens of MHz. Impedance Analysis characterization is a key technology that enables new materials development for semiconductors, smart-materials, ferroelectrics, piezo-electrics, solid oxide, solid electrolytes, ceramics, polymers, OLED and many more materials.
-
Product
Automatic Incident Detection
TrafiBot2
-
The FLIR TrafiBot2 is a compact, rugged camera solution for automatic incident detection. Combining full HD visual imaging with advanced video analytics, TrafiBot2's advanced processing generates traffic data and incident detection information for tunnels, bridges, and highways, including alerts on stopped vehicles, wrong-way drivers, and lost cargo.
-
Product
Shock Test Systems
-
Sanwood Environmental Chambers Co ., Ltd.
Is featured with advanced design, high degree of automation and reliability, simple operation and convenient maintenance. The system meets the requirements of both shock and collision test, can perform conventional half-sine wave, post-peak sawtooth wave, square wave and other waveform shock tests.
-
Product
Automatic Hardness Testing System
AMH55
-
Maximize your productivity and easily measure impressions on various surface conditions for a wide number of applications with LECO’s new AMH55. The AMH55 introduces LECO’s innovative Cornerstone® brand software to our hardness testing platforms, for increased usability, simplified reporting, and streamlined analysis times. Supporting accurate and efficient microindentation and Macro/Vickers hardness testing in fully automatic, semi-automatic, and lite configurations, the AMH55 is a valuable resource for users needing precise and productive hardness testing while tailoring the data and results to their needs.
-
Product
High Power & Voltage Pack Testing System
FTF
-
Drive simulations with standard Electric Vehicle tests: FUDS, SFUDS, GSFUDS, DST and ECE-15LDrive Cycle TestingIntegration with motor test benchesCycle testing of EV/HEV Battery Packs
-
Product
Automatic Calibration Module
ACM2708
-
ACM2708 is an automatic calibration module that can be used with CMT Vector Network Analyzers operating in frequency range up to 8 GHz. The ACM 2708 is a 75 Ohm calibration module for use with native 75 Ohm VNAs (S7530) while also covering automatic calibration for 50 Ohm VNAs with the use of 50 to 75 Ohm matching pads.
-
Product
Automatic Measurement
Mylab V
-
For performing automatic measured simply and easily scenario tabular to make with software such as Microsoft Excel, Mairabo V is the instrument control tool regardless of manufacturer.
-
Product
VLF Testing and Diagnostics System
PHG 80 TD/PD
-
Cable testing and diagnostics with the BAUR PHG 80 TD/PD. With the PHG TD/PD, you get a multifunctional cable testing and diagnostics system that was specially designed and developed for medium-voltage networks. The PHG TD/PD system is also the only cable testing and diagnostics system that gives a comprehensive overview of the quality and ageing condition of the test sample. The diagnostic methods TD and PD are mutually complementary, because on one hand you can detect the complete condition and on the other hand locate individual faults in the operating resources.* High performance VLF truesinus testing device (3 kW) with regulated output voltage* Compact, enclosed design in 19" format* Variable installation option with separate control and voltage unit* Variable connection options to cable stations of different models
-
Product
Tensile Testing System With Thermostatic Chamber
-
This thermostatic chamber is ideal for long-stroke tensile testing of large-elongation materials such as rubber and plastic in controlled temperature environments.
-
Product
Reconfigurable Automatic Tester
-
Quick-Start Reconfigurable Automatic TesterCompact, Efficient Desktop Tester with Customer-Configurable PXI/PXIe Insert PXI/PXIe Insert – 8 Slots: 1 Controller, 7 Customer-Configurable PXI/PXIe Slots.
-
Product
Optics Test Systems
IR Autocollimator
-
Optik Elektronik Gerätetechnik GmbH
The infrared autocollimator was specially designed for the 1550 nm wavelength range. In conjunction with the CROSDETECT evaluation software, it achieves a measuring accuracy of 1 arcsec with a resolution of 0.1 arcsec. The camera used is suitable for the wavelength range from 900 nm to 1700 nm.
-
Product
Test Systems
-
In-Circuit Test (ICT) tests populated circuit boards by means of electronic measurements through thin needles on test fixtures. We offer in-circuit testers for various testing strategies – from the flexible 19“ rack to the ergonomic high-performance tester. And all of our in-circuit testers are also available in the Lambda edition for true parallel testing. The flying probe test checks your printed circuit boards using four movable test heads. This requires no fixtures and allows for flexible test program generation. That makes our flying probe test systems ideal for a high mix of printed circuit boards and small to medium test volumes, such as for prototype testing.
-
Product
Robotic Cell for Testing Car Multimedia System
-
It is necessary to develop an automated system for testing a multimedia device. The system should perform functional testing: testing of physical buttons, touch screen and logic of operation.
-
Product
Camera Barrel Test System
BK8612
-
We designed the BK8612 2 Channel Noise Test System to provide noise and vibration testing for your digital camera barrel DC Motors. Because it is based on the BaKo BK2120B DAQ, it is capable of monitoring a microphone and an accelerometer concurrently to obtain data from the motor. Because you can change the parameters of functions and limits, it is versatile but still quick and easy to set up. In addition, you can look at data in real time and also store it for future analysis. Easy to use and set up, fast and accurate; if you need to maintain the quality of your camera barrel motors, this is the tester you want.
-
Product
Automatic Cleaning and Calibration
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Fully automatic process monitoring in combination with the analysis measuring system Protos and the retractable housings SensoGate or Ceramat. Highly accurate measurements even under difficult process conditions such as high pressure, high temperatures and high levels of impurities.
-
Product
Massively Parallel Board Test System
I7090
-
The Keysight i7090 is a massively parallel board test system designed to help PCBA test engineers improve manufacturing efficiency while reducing costs. Unlike traditional in-circuit testers, the i7090 supports up to 20 In-Circuit Test cores in parallel, which means engineers can test multiple Units Under Test (UUTs) simultaneously without the need for multiple systems. This reduces scaling and infrastructure costs and frees up valuable testing space.
-
Product
Multi-DUT Mobile & IoT Test System
IQxstream-M
-
Its ultra-compact design and flexible architecture makes it highly suitable for high volume manufacturing of smartphones, tablets and cellular IoT modules.
-
Product
Controlled impedance test system
CITS900s4
-
CITS900s4 is the seventh generation of Impedance test system from polar, and typically the most popular model for customers who are new to impedance control. CITS900s4 provides both differential and single ended measurement capability along with 4 channels to provide flexible probe connection.
-
Product
Computer-controlled Torque Testing System
Torque Testing System,
-
Our top-of-the-range Vortex-i torque testing system gives optimum testing performance and evaluation options, enabling you to get the most from your test measurements.
-
Product
Combination Board Functional Test System
QT 4256 ATE
-
Qmax Test Technologies Pvt. Ltd.
QT 4256 ATE is a combination Board Functional Test System , a main frame Automated Test Equipment (ATE) which can be configured up to maximum of 1280 Bi-directional digital channels ideal for testing circuit card assemblies of high level of complexity and whether it is a legacy or new generation PCB.
-
Product
Traction and Induction Motor Test Systems
-
Crest makes state-of-the art test systems for testing 3-phase AC motors used in traction and other industrial applications.
-
Product
Electronic Test And Measurement Systems
-
Summaries, information, & tutorials about electronics test and measurement equipment & techniques.
-
Product
PD Test Systems
-
1. Number of channels: 2/4 electric signal interfaces & 1 EXT interface 2. Sampling frequency: maximum 200MGa/s 3. Sampling precision: 12bit 4. Range: 0.1mV~20V 5. Range switch: 1mV, 2mV, 5mV, 10mV, 20mV, 50mV, 100mV, 200mV, 500mV, 1V, 2V, 5V 6. Frequency band range: 1Hz-60MHz 7. Range non-linear error: 5% 8. Range of capacitance for test object: 6pF~250µF 9. Power source mode: internal lithium cell / AC 220V 10. Display: 6.5 inches TFT LCD 11. Resolution: 640×480 12. PV: 4GB 13. Hard disk: 32G stiff disk used for storing the test data
-
Product
LCR Meter For High Current Test System
5400L Series
-
WK5400 is the test system controller. The DC Bias Current source WK3265B machines are connected to the Bias Adapter of the 5400 directly with a dedicated wiring system. This makes it is easier to set up and maintain the system.
-
Product
Universal Test System
LS6601A
-
LS6601A Universal Test System is based on LXI bus, primarily used for functional electronic product or system verification, test parameters. Because the system design is based on LXI bus structure, so its addition to general characteristics of versatility, scalability, but the architecture of the system more flexible, the test system is not limited to one or more cabinets, but may be needed test network and multiple LS6601A and can be easily grouped into one or more of the ground test system, depending on the test mechanism, form a powerful set of test, control, simulation, simulation, data management as one; distributed in different places .
