-
Product
Capacitance Tester
LCR55A
-
The ultimate electronic component verifier measures inductance, capacitance, resistance, transistors, diodes and microwave diodes.
-
Product
Paramagnetic Oxygen Analyzer
Model T802
-
The Model T802 O2 uses the proven paramagnetic measurement principle, coupled with state of the art microprocessor technology, to provide accurate and dependable measurements of Percent-Level O2.Paramagnetic technology is non-depleting, which means that there are no consumable parts, and ensures a consistent performance over time. The selectivity of the paramagnetic measurement for oxygen means that there is little or no interference from other common background gases. The T802 offers a stable and inherently linear measurement of oxygen, making it possible to calibrate the analyzer by checking only two points. There is no requirement for a reference gas during operation.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T802 comes with the NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
Fluid Level Sensor
-
The output of the fluid level sensor is a voltage which changes in direct proportion to the level of fluid in the probe. The difference in permittivity between air and the fluid being measured changes the capacitance between the probe's two concentric tubes as the level changes. An RS232 connection to a PC allows the user to calibrate the fluid level and thermal drift compensation. The probe is factory replaceable, allowing the electronics to be re-used should the probe become damaged or if a new probe length is required.
-
Product
DC Bias Injector
J2130A
-
When using the network analyzer to measure impedance, such as the capacitance and ESR or a capacitor, or the DCR of an inductor, etc., it is often necessary to provide a voltage bias to the device being tested. This is true of semiconductor junction capacitances, varactors, and some ceramic capacitors (especially X5R). In these cases the impedance is a function of the DC bias on the device. The Picotest DC bias injector (J2130A) is used for this purpose during impedance measurements.
-
Product
Oscilloscope - 1 GHz, 4 Analog Channels
DSOX3104T
Oscilloscope
1 GHz4 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
High Frequency LCR Meters up to 30MHz
11050
-
Chroma Systems Solutions, Inc.
The Chroma 11050 Series HF LCR Meter is a precision test instrument designed to accurately measure and evaluate passive components at high speeds. Its measurement capabilities cover the primary and secondary parameters required for testing the inductance, capacitance, resistance, quality factor and loss factor of passive components. The HF LCR Meter has a broad testing frequency range 75kHz~30MHz/1kHz~10 MHz/60Hz~5MHz suitable for analyzing component characteristics under different frequencies. Its 0.1% basic measurement accuracy provides stable and highly reliable results. A fast 7ms measurement speed effectively increases productivity when working in an automated environment.
-
Product
Oscilloscope - 350 MHz, 2 Analog Channels
DSOX4032A
Oscilloscope
350 MHz2 analog channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing
-
Product
Bench Digital Multimeter, Calibrated, Data, 1 kV, 10 A, 3.8 Digit
72-1015 CAL D
-
The 72-1015 CAL D from Tenma is a digital bench type true RMS multimeter. It has auto and manual range options with maximum reading of 5999 counts and 3-5/6 digits which has a unique outlook design. In addition to all the conventional features including DC/AC voltage, current, resistance, diode, continuity test, diode test capacitance, temperature, transistor, max/min, there is a data hold, low battery display, sleep mode, RS232C serial port for easy connection with computer to realize macro recording, monitoring and capture of transient dynamic data, displaying change of waveform during the measurement, providing data and evidence to engineering technicians for scientific research. This meter complies with the standards IEC61010, pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) double insulation and CE marked.
-
Product
LCR Meter
-
Precision Mastech Enterprises Co.
An electronic test device that measures Inductance (L), Capacitance (C), and Resistance (R) of components like capacitors, inductors, and resistors, often at various frequencies, to determine their actual values and parasitic characteristics beyond simple DC readings, essential for verifying component quality and suitability for circuits.
-
Product
Capacitance Meter
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
Inductance capacitance meter is a kind of stable performance, safe and reliable, high precision of handheld 3 1/2 a manual switch range digital instrument. Can be used to measure the capacitance, resistance, triode magnification beta and other functions
-
Product
Oscilloscope: 200 MHz, 4 Analog Channels
DSOX3024T
Oscilloscope
The DSOX3024T, 200 MHz oscilloscope provides 4 analog channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate and standard touch zone trigger with an 8.5-in capacitive touch screen.
-
Product
LCR Meters
-
An LCR meter measures impedance (inductance, capacitance and resistance) at spot frequencies.It is used for testing components and materials in R&D applications and in componet manufacturing.
-
Product
NI TB-2642B Terminal Block for NI 2532B as 1-Wire 16x32 Matrix Topology Without Column Protection Resistors
782385-05
Terminal Block
The TB-2642B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2642B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2642B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Dual, Low Noise, Coaxial Cable Optimized
DCOAX
-
Very high precision, three-terminal capacitance measurements can be affected by the self-inductance of the test cables, mainly at higher capacitance values. Magnetically induced noise can also reduce the quality of measurements. The cable now offered by Andeen-Hagerling both minimizes these problems and provides a way to standardize the residual self-inductance.
-
Product
RA Family Of Arm-based MCUs
RA2
-
The RA2 Series is the RA Family's entry-level 32-bit MCU, offering excellent cost performance and ultra-low power consumption. It delivers up to 48MHz of CPU performance using an Arm® Cortex®-M23 core with up to 256kB of embedded flash memory and a wide single voltage supply range from 1.6V to 5.5V. With cutting-edge peripherals like capacitive touch, the RA2 Series is ideal for system control or user interface applications such as in healthcare devices, home appliances, office equipment, and measuring equipment.
-
Product
Oscilloscope 500 MHz, 2 Analog Channels
DSOX3052G
Oscilloscope
The DSOX3052G 500 MHz oscilloscope provides 2 analog channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
Transformer Testing And Monitoring
-
Can detect the symptoms of transformer failure by monitoring the cooling system, load tap changer, dissolved gas, bushing power factor and capacitance, partial discharge, oil levels, pressure, temperatures and more.
-
Product
EIS Battery Analyzer
BA8100
-
The BA8100 is designed to accurately measure the internal impedance of a single cell or battery stack with voltages as high as 80 V. In addition to impedance, auxiliary measurements include voltage, current, phase, capacitance, inductance, quality factor and more. With the provided software, the BA8100 can perform Electrochemical Impedance Spectroscopy (EIS) across a frequency range of 50 mHz to 10 kHz. The impedance spectrum can be evaluated through the Nyquist and Bode plot tools to determine effective series resistance (ESR) and track battery health. Included with the BA8100 is a self-test fixture to verify the instrument’s performance or compensate for resistance introduced by the test leads.
-
Product
Capacitive Sensors
-
Capacitive sensors (capacitive linear displacement sensors) are noncontact devices capable of high-resolution position measurement and/or position change - displacement measurement - of any conductive target.
-
Product
NI TB-2646B Terminal Block for NI 2532B as 1-Wire Quad 4x32 Matrix topology With Column Protection Resistors
782385-14
Terminal Block
The TB-2646B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire dual 4x32 or 1-wire quad 4x32 matrix. You can directly connect the TB-2646B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2646B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Industrial IP69K Stainless Steel Panel PCs With 11th Gen Intel® Core™ Processor
Titan2
Panel PC
- 11th Gen Intel® Core™ i5/i3 BGA type processor- 15.6”/21.5”/23.8” FHD with projected capacitive touchscreen- Full IP69K rating for dust and water ingress- Corrosion-resistant 304 stainless steel enclosure (316 for Option)- All M12 type connectors suite for harsh environments- Optional for optical bonding and high brightness (1000 nits)- Standard VESA, Yoke/Pipe mount (optional)
-
Product
High Impedance Probes
-
Everbeing offers GGB’s high impedance active probe for failure analysis of your devices. The high impedance with low capacitive design allows measurements of internal nodes without loading the device. For more information, please visit http://www.ggb.com.Everbeing offers GGB’s high impedance active probe for failure analysis of your devices. The high impedance with low capacitive design allows measurements of internal nodes without loading the device. For more information, please visit http://www.ggb.com.
-
Product
15.6" Fanless Widescreen Panel PC With Intel® 13th Gen Core™ I7/i5/i3 Processor
PPC-415W
-
15.6" true-flat Full HD LCD panel with projected capacitive touchscreen, anti-glare coatingIntel® Core™ i7-1365URE/i5-1345URE/i3-1315URE processor with fanless system designSupports PCIe x4 or PCI expansion1 x isolated RS-422/485 with auto flowWide input power range (9 ~ 32 VDC)Dual 2500BASE-T Ethernet Supports Time-Sensitive Network(TSN) technology3 x Independent displays1 x M.2 bay (2242/2280) for storage onlySupport TPM2.0 hardware security
-
Product
Pressure Sensors
ESCP-SAPT Transmitter
-
ESCP-SAPT pressure transmitters consist of a MEMS capacitive pressure sensor die, which is underpinned by ES’ innovative microfabrication process that has been proven suitable for the mechanical, radiation and temperature environment of space applications. The full custom, radiation-hardened signal conditioning IC was designed entirely by ES, utilizing a standard deep submicron CMOS process of a European foundry.
-
Product
InfiniiMax Probe, 3.5 GHz
1131B
Oscilloscope Probe
Provides extremely low input capacitance, flat frequency response, and patented resistor probe tip technology.
-
Product
Proximity Sensors
-
Omron's proximity sensing portfolio encompasses a wide range of capacitive and inductive sensors that meet all needs for durability in industrial environments.
-
Product
Compact Pressure Transducers And Switches
-
Compact Baratron® capacitance manometers are ideal for space constrained applications. Compact pressure transducers provide an analog output proportional to pressure, while compact pressure switches provide a relay output based on pressure.
-
Product
21.5" Fanless Widescreen Panel PC With Intel® Core™ I5-7300U Processor
PPC-3211W
Panel PC
21.5" true-flat Full HD LCD panel with projected capacitive touchscreen, anti-glare coatingIntel® Core™ i5-7300U(default); i7-7600U/i3-7100U(optional) processor with fanless system designSupports PCIe x4 or PCI expansion1x isolated RS-422/485 with auto flowWide input power range (9 ~ 32 VDC)Dual Gigabit Ethernet with IEEE1588 support3x Independent displays1x M.2 bay (2242) for storage only & 1x TPM 2.0 internal support (optional)No RED Certification
-
Product
Phasing Meters
-
A unique tool in that it may be used as a conventional phasing meter, or the meter probe may be used as a stand-alone voltage detector on primary or secondary voltages or capacitive test points.
-
Product
PXI Solid State Multiplexer, 5 Amp, Single 48-Channel, 1-Pole
40-652A-001
Multiplexer Module
The 40-652-001 is a 48-channel, 1-pole MUX and is part of our range of multiplexers uses solid state relays with high tolerance to surge currents and hot switching events. These multiplexers provides an isolation relay in the common to minimize capacitive loading when expanding the multiplexer across multiple modules. The 40-652 can sustain 30A for 300µs on hot or cold switching.
