-
Product
Parallel Active Multifunction Filter
SINAF 3.0
-
Lifasa - International Capacitors, SA
The active filters offer the best possible solution to solve the problems related to the quality in the electrical network, both in industrial three-phase installations, as commercial or service installations. These problems are caused, not only by the harmonics, but also by the consumption of reactive power (generally of capacitive type).
-
Product
Analogue (1kV below) Insulation Tester
2132 IN
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on low ohms : 3Ω & 500Ω.● Compact and lightweight.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test. ● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● BS 16 edition.
-
Product
Dual 10th Order Lowpass Filter
64-VBF
-
The 64-VBF 10th order Lowpass Filter is a dual channel filter with independent switch settable Cutoff Frequency (Fc). The filter has a linear phase DC accurate root raised cosine response. The unit’s differential inputs are built to withstand high DC over-voltages up to ±50 VDC and greater than ±100 V transients. Gain of the unit is 1 allowing for minimal insertion issues. The output can drive a high speed DAQ multiplexer with its fast settle and capacitive drive capability.
-
Product
LCR Meter
-
Precision Mastech Enterprises Co.
An electronic test device that measures Inductance (L), Capacitance (C), and Resistance (R) of components like capacitors, inductors, and resistors, often at various frequencies, to determine their actual values and parasitic characteristics beyond simple DC readings, essential for verifying component quality and suitability for circuits.
-
Product
Semiconductor Device Parameter Analyzer/Semiconductor Characterization System Mainframe
B1500A
-
Current-voltage (IV) measurement capabilities of spot, sweep, sampling and pulse measurement in the range of 0.1 fA - 1 A / 0.5 V - 200 VAC capacitance measurement in multi frequency from 1 kHz to 5 MHz and Quasi-Static Capacitance-Voltage (QS-CV) measurement capabilitiesAdvanced pulsed IV and ultra-fast IV measurement capability from minimum 5 ns sampling interval (200 MSa/s)Up to 40 V high voltage pulse forcing for non-volatile memory evaluation
-
Product
Battery Testers
-
designed to accurately measure the internal impedance of a single cell or battery stack with voltages as high as 80 V. In addition to impedance, auxiliary measurements include voltage, current, phase, capacitance, inductance, quality factor and more.
-
Product
Loop and Line Powered Level Switch
Safety IntelliPoint
-
The Safety IntelliPoint level switch provides a capacitance probe level switch with either a current output or relay contacts and “On-Board” self-diagnostics to ensure reliability. This SIL Intellipoint conforms to SIL 2 specifications providing the ultimate in level switch integrity and level sensing elements for a wide variety of temperatures, pressures, and materials.
-
Product
Oscilloscope - 200 MHz, 4 Analog Channels
DSOX4024A
Oscilloscope
200 MHz4 analog channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, dual-ch 20 MHz arbitrary WaveGen, 3-digit DVM, serial trigger and analysis & mask testing
-
Product
Dielectric Material Test Fixture
16453A
Test Fixture
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
Product
Hi-Speed Discrete Test System
QT-6000
-
QT-6000 Test System, with built-in capacitance test (DC+CAP) and Scanbox etc, is applicable to devices like medium & small power transistors, MOS-FET, diodes and Wafer.
-
Product
MIS Capacitors
-
The SemiGen 8000 and 8100 series of MIS Capacitors are available in a wide variety of capacitance ranges and sizes. They are made with prime starting material and consist of an Oxide/Nitride layer that provides low dielectric loss and high standoff voltage. These RF microwave chip capacitor products are available in chip form only.
-
Product
Mixed Signal Oscilloscope 100 MHz, 4 Analog Plus 16 Digital Channels
MSOX3014G
Oscilloscope
The MSOX3014G 100 MHz oscilloscope provides 4 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
Voltage Testers
-
The non-contact voltage tester detects live conductors on cable connections, cable drums, sockets, switches, junction boxes etc. Due to capacitive measurement procedures, no current flow is required and interruptions can be indicated quickly and accurately.
-
Product
7" Capacitive Touch Panel Overlay
-
The LattePanda 7-inch touch panel overlay uses capacitive touch technology and multi-touch to bring you a truly interactive experience. Simply overlay the panel on your LattePanda 7-inch display, power the board, and you will have a high-quality user interface that you can use to create all-in-one, integrated projects.
-
Product
Bench Type LCR Meter
LCR-900
-
*Dual LCD Display. *Capacitance, Resistance, Impedance, Inductance, Quality Factor, *Dissipation Factor Phase Angle. *Auto Detect Function. *Open Circuit/Short Circuit Compassion. *Operation Frequency 100Hz to 100KHz. *Basic Accuracy: 0.3% *Measurement Voltage Fixed at 0.6Vrms.
-
Product
Contactless Wafer Geometry Gauge
MX 20x series
-
The E+H geometry gauges are based on two heavy plates mounted parallel to each other. Embedded in the plate are a set of capacitive distance sensors. The wafer will be moved manual or automatically between the plates and measured without any movement.
-
Product
Digital Multimeters
HDM3065 series
-
Qingdao Hantek Electronic Co., Ltd.
6 1/2 bit resolution;front and back multimeter input,measure a key switch;statistic analysis、 histogram and run chart display function;Double display measurement function,display 2 kinds of signal parameters at the same time;3A/10A current range;4.3 inch 64K LCD;0.1uV resolution,easy to use,parameters can be setted easily; 13 kinds of measure functions:DC Voltage, AC Voltage, DC current, AC current, 2 line resistance, 4 line resistance, capacitance, diode, connectivity, frequency, period, Arbitrary sensor, temperature.
-
Product
Capaciter Tester
KS-1600
-
Konstar Electric Industrial Co., Ltd
It is a dial instrument, and has the stable function and high reliability. It is driven by the battery. The instrument makes use of the indicator plate(102*79mm), thus displays clearly.This instrument can test the data of on-line capacitive resistance and on line impedance. It is an excellent instrument and an ideal tool for the people in labs, factory and household. When testing the mounted capacitor, it does net need to be completely out of power nor do the meter, and the meter can be testing continuously.
-
Product
Capacitance Tan-Delta Test Set
-
Since our establishment in the year 1975, we have been engaged in manufacturing and exporting Capacitance Tan-Delta Test Set. This test set is extensively used to measure dissipation and capacitance of various equipment. Manufactured at our well-equipped manufacturing unit as per set international quality standards using supreme quality components, this test set is tested thoroughly by our quality analysts on various defined parameters. Offered Capacitance Tan-Delta Test Set can be purchased from us at pocket-friendly prices.
-
Product
Electrical Measurements Test
-
The tests are performed to measure and collect data from electrical and electronic parts using various measurement methods including, but not limited, to the following: capacitance, resistance, winding resistance, insulation resistance, magnetic permeability, power input, and quality factor Q.
-
Product
Capacitors - Binary Chip
-
Macom Technology Solutions Holdings Inc.
MACOM’s BOO and BSP Series Capacitors are designed to facilitate bread-boarding or to use where a trimming capability is required. These devices feature the same dielectric layer and bonding surfaces as our 9000 and 9100 Series chip capacitors. By connecting the pads in parallel, the capacitance values are additive, so many combinations are possible.
-
Product
Air Temperature and Relative Humidity Sensors
-
Air temperature and relative humidity probes typically consist of two separate sensors packaged in the same housing. Often relative humidity is measured with a capacitive RH sensor, while air temperature is measured by a PRT.
-
Product
Transducer Calibration
m+p SensCal
-
Regular transducer calibration is an essential requirement for maintaining the accuracy, reliability and repeatability of the results obtained from a measurement system. m+p international’s m+p SensCal program provides a quick and simple process for calibrating accelerometers (piezo-electric with charge output or IEPE, piezo-resistive, capacitive) in your laboratory, as well as velocity or displacement transducers.
-
Product
Software
Conductance Measurement and Analysis
-
Materials Development Corporation
MDC uses conductance to give a complete picture of MOS devices as well as to correct for series resistance effects. MDC C-V plotters use conductance and capacitance measurements to plot true device capacitance and depletion region conductance.
-
Product
TAP Signal Isolation Module
JT 2139
-
The JT 2139 is a TAP signal isolation module designed for use in combinational test systems that utilise multiple instrument interfaces. To avoid parasitic capacitance effects and/or unwanted ground loops the JT 2139 can be used to completely galvanically isolate any JTAG Technologies boundary-scan controller from the remainder of the instrumentation system. JT 2139 isolators are a standard component of the JTAG Technologies ‘Symphony’ systems that integrate boundary-scan with In-Circuits Testers etc..
-
Product
Substation Equipment Test Van
ETL-250
-
Apart from insulation withstand testing with DC (rectified) voltage up to 60 kV and ability to measure very small leakage currents, the system can be used for testing various objects with small electrical capacitance with AC voltage of up to 250 kV and measuring dielectric dissipation factor (Tan Delta) at industrial frequency.
-
Product
Transformer Testing And Monitoring
-
Can detect the symptoms of transformer failure by monitoring the cooling system, load tap changer, dissolved gas, bushing power factor and capacitance, partial discharge, oil levels, pressure, temperatures and more.
-
Product
Liquid Test Fixture
16452A
Test Fixture
The 16452A provides accurate dielectric constant and impedance measurements of liquid materials. The 16452A employs the parallel plate method, which sandwiches the liquid material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixure.
-
Product
Hydrophone
RESON TC 4033
-
The TC4033 provides uniform omnidirectional characteristics within the full frequency range of 1Hz to 140kHz. The Typical sensitivity of -203dB re 1V/µPa and the capacitance of 7nF, ensure an excellent signal to noise ratio, thereby allowing TC4033 to be used with extension cables with only a limited reduction in sensitivity. The TC4033 offers excellent acoustic characteristics and durability, which makes it ideal for a wide range of applications and for calibration purposes.
-
Product
Multimeters
-
A multimeter is a measuring instrument whose function is to measure electrical quantities such as voltage, current, resistance, capacitance and inductance.They are a perfect measurement solution in various fields of industry.
