Breaker Test Systems
-
Product
Battery Pack Test System
-
*Easy to see now test progress*Can cycle test*Provide Charge, Discharge, Suspend, FOR, LOOP Mode Select*When Charging, set the stop current to stop charging when fully charged so as to avoid overcharging that will damage the battery. When Discharge, set the stop voltage to stop discharge when discharging to lowest so as to avoid over-discharging that will damage the battery.
-
Product
Brake Test Systems
-
Worldwide, high-speed transport is getting more important. Only through continued improvement and expansion of braking systems, will suppliers all around the world provide a solid foundation for safe traffic. HORIBA has been successfully making brake test stands for more than 90 years.
-
Product
Test system for Electronic Device
PCB
-
The main focus of the test system is validation and functional testing of electronic devices. The tests include electrical parameters and logical functions of the firmware. Device groups can be stimulated externally and output signals can be acquired by the test points on the board. Limits and ranges of the acquired signals can be monitored and stored for verification.
-
Product
System Controllers
-
System Controllers feature multi-device control, variable speed control, fiber optic interface with antenna mast and turn table, full control via front panel or PC software, on-site antenna calibration, 19" 3U rack-mountable, and a 3-year warranty.
-
Product
Shaker Systems
-
Vibration Research Corporation
Small force vibration testing equipment and shakers for product and modal analysis testing. Each system consists of a shaker and a matching linear direct-coupled power amplifier. Additional components may be added to the basic system to tailor it to your specific needs.
-
Product
Test Port Cable, 1 Mm
11500I
-
Connect test ports to devices, fixtures, or probe tips with this 8.8-cm cable featuring a return loss of 17 dB minimum.
-
Product
Measurement System
MS-500 series
-
The MS series is suitable for pre-processing analog signals.The plug-in units of filters, differential amplifiers, isolation amplifiers, etc. can be installed into their frames.(16 channels at maximum/the JIS rack size)
-
-
Product
Tire Rolling Resistance Test System
-
This system measures the rolling resistance of each tire accurately. In addition to the simultaneous measurement of tire loss resistance and rolling resistance coefficient for each drive by mode operation (JC08, WLTC), coasting test, constant acceleration/deceleration test and transient mode test are able to be performed. Furthermore, measurement of driving noise/ vibration of the tire, effect of the tire loss due to the temperature change can be verified by adding options.Conforming the JIS D 4234: 2009 and ISO 28580: 2009.
-
Product
Automated Testing System
PV-LIT
-
Thermographic solutions ensure high quality of solar cells and modules.Usable for all types of solar cells and modules (silicon-based or thin-layered)Testing in laboratory and in-line in the course of the manufacturing processTesting of various solar cells and modules through contact and non-contact measurementCell-specific system configuration and determination of test criteria and kind of defects
-
Product
Telephone Headset and Handset Test System
2000HT
-
TE2000 Headset Tester for audio testing headsets and handsets using computer generated test sounds.
-
Product
Polarity & Burn in Test Systems
-
Our polarity and burn-in test systems are available for components such as multilayer, disc type or hollow ceramics.
-
Product
Massively Parallel Board Test System
I7090
-
The Keysight i7090 is a massively parallel board test system designed to help PCBA test engineers improve manufacturing efficiency while reducing costs. Unlike traditional in-circuit testers, the i7090 supports up to 20 In-Circuit Test cores in parallel, which means engineers can test multiple Units Under Test (UUTs) simultaneously without the need for multiple systems. This reduces scaling and infrastructure costs and frees up valuable testing space.
-
-
Product
Integration of Inline Test Systems
-
The test system and adapter can also be integrated in inline test systems. Additional communication can take place via interfaces (e.g. RS232, DLL). We have already created numerous integrations for different manufacturers.
-
Product
Functional Test Systems
-
With extensive experience in functional test equipment, a world-wide service and support organization, and a broad range of software/hardware options, we will supply cost-effective production-ready test solutions to meet your test challenges. Proposals developed by our functional test engineering team include a detailed description of system requirements, test instrumentation, estimated test cycle times (as applicable), footprint, and other key specifications.
-
-
-
Product
High Power Laboratory Testing System
FTF-HP
-
Drive simulations with standard Electric Vehicle tests: FUDS, SFUDS, GSFUDS, DST and ECE-15LDrive Cycle TestingIntegration with motor test benchesCycle testing of EV/HEV Battery PacksBi-directional DC power supply
-
Product
Metrology Systems
-
High-precision, wavefront-based tools for measuring and testing optical components, specializing in Shack-Hartmann sensor technology.
-
Product
Development System
FE-51MX
-
* Emulates Philips P8xC51MA/B/C , P89C669 Microcontrollers * 1MByte Code Memory * Based on bond-out Technology * Frequency up to 24MHz 3V / 5V Operation * Huge Real Time Trace Memory * Windows Debugger for C/C++ and Assembler * Target Board Included * RS-232 or USB Interface * 64K C/ASM and 8K C++ Included
-
Product
DC Parametric Test System with Curve Trace
DC3
-
The wafer has been fully tested, cut and packaged. Today's IC manufacturers are finding tremendous cost savings in performing just fast DC tests on these packaged parts rather than running the full wafer tests all over again. Until now this required either an expensive full-power IC tester, or a "rack-n-stack" collection of instruments. Enter the HILEVEL DC3 Co-Optive Parametric Tester. No more instruments, no switching matrix, no tricky software. The DC3 combines a high-precision DC-PMU and internal DUT supplies to test up to 2,048 pins, all in a single chassis with Multi-Site capability up to 64 sites. And every DC3 includes our Classic Curve Trace feature, allowing easy curve tracing on every pin.
-
Product
Hardware-Software System
Shock Impact Recorder
-
This system is complex of recording instruments intended for measurement and recording of shock impact parameters produced by shock testing machines.
-
Product
Test Automation System for Driveline Testing
STARS Driveline
-
STARS Driveline is an integrated automation, acquisition and control system that provides a broad range of application functionality in a single, powerful environment. It has been designed to fulfil the specialist requirements and applications for driveline testing from simple modal testing on two or four wheel drive systems, to RLS simulation or advanced applications such as service load replication (SLR).
-
Product
Measurement System
BLS-I/BCT-400
-
The BLS-I/BCT-400 measurement systems perform lifetime measurement on monocrystalline or multicrystalline silicon (ingots or bricks) without requiring surface passivation.
-
Product
Automation Systems
-
Omron's extensive portfolio of PLC and MAC controllers, networking solutions, remote IO, IPC and HMI technology support a fully integrated application
-
Product
HEV / EV / Grid Emulators and Test Systems
-
With Scienlab test systems and test software, Keysight offers customized test environments for the development and testing of electronic components according to hybrid and electric vehicle testing standards. Our solutions help you to accelerate your e-mobility applications from the battery, Battery Management System (BMS), inverter, the charging interfaces of Electric Vehicle (EV), and Electric Vehicle Supply Equipment (EVSE).
-
-
Product
Measuring Systems For Night Vision Systems
MTF Master IIT
-
Optik Elektronik Gerätetechnik GmbH
Measuring system for MTF, SNR and EBI of Image Intensifier Tubes (IIT). The MTF MASTER IIT was specially developed to classify the quality of image intensifier tubes by the objective criteria of the MTF (Modulation Transfer Function).
-
Product
Military Test Systems
-
Santa Barbara Infrared is the leading supplier of sophisticated, integrated, multi-function E-O test systems used by the military in laboratory, factory, depot and field test environments. Each of these systems are built to specific requirements and utilize SBIR’s extensive design and test capabilities, core technologies and knowledge of the unique military applications. SBIR specializes in providing complete solutions with integrated hardware and software resulting in robust and easy-to-use systems.
