Load Cell Simulators
generate a precise mV/V signal to assure load cell amplifier, tester, readout and display set up.
See Also: Load Cell Test, Load Cells
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, 1 kV Isolation
41-752A-111
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Load Cells for Weighing
-
HBM provides the optimal Load Cell or Load Sensor for your application. Beam Load Cells: The All-Rounders For Weighing Technology. Ring-Torsion Load Cells: Low Profile And Powerful. Canister Load Cells: Maximum Capacities Up To 400 t. Single Point Load Cells: The Standard in Scales Manufacturing. Digital Load Cells: Ideal For Dynamic Weighing. Weighing Modules: Pre-assembled For Tank And Silo Weighing.
-
Product
load cell
EST-40
-
Technopark Automation & Control
The EST-40 is an 'S' type load cell suitable for use in tension and compression and is popular on hopper, tank weighing, belts scale and process weighing applications. It is low cost and is available in capacities from 50 kg to 2000 kg.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for PCIe
ACPe825-x
-
ARINC825 (CAN bus) Test & Simulation module for PCIe with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825 PCIe card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
PXI Strain Gauge Simulator Module 4-Channel, 3k
40-265-104
-
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 3kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Solar Simulator for Concentrator Cells
-
Optosolar offers solar simulators with continuous light for small area solar cells (ca. 10mm x 10mm). depending on the cell size, the concentration ratio can exceed 1000 suns. Special designs cover low concentration on large area wafers (156mm x 156mm), as well as line focus applications (e.g. 8mm x 156mm at 8 suns). Flashlight Solar Simulators have the advantage of negligible temperature change to the solar cell. For this reason, they are often used for very high concentration ratios or for multijunction cells in a solar simulator with adjustable spectrum.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, Simplified Current Sink, 750 V Isolation
41-752A-903
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, 750 V Isolation
43-752A-003
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
-
Product
Load Cells
-
For use in harsh environments, our Models T66 (bending beam),T85 and T85-T(shear beams)are manufactured fromstainless steel, fully welded and hermetically sealed to provide total environmental protection (IP68 and IP69K). The T85-Tmodel has a blind loading hole, ideal for use in platform scales.
-
Product
Load Cell Measurement Interface
LCIC-1106a
-
Industrial Measurement Systems Ltd.
Any application related to weighing or measuring forces is now available in your PC...Stand-alone microcomputer-based interface card requires no other interfacing accessories. Simply connect th
-
Product
Rod End Load Cell
-
Futek Advanced Sensor Technology, Inc.
FUTEK’s Rod End Load Cells provide an excellent solution for applications involving Inline Actuators or Hydraulic Jacks with Male/Female Threads. You will find a capacity
-
Product
PCI Strain Gauge Simulator Card, 4-Channel, 2k
50-265-304
-
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Load Cells
-
Selection of load cells must always be guided by the end users particular system requirements and by the application. The PIAB Load Cells range from typical compression/tension load cells to S-beam and shear beam types for stationary applications as well as for mobile weighing systems.
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 24 Channel
41-761-002
-
The 41-761-002 is a low voltage 24-channel output module ideal for simulating theoperation of a thermocouple, also available with 32, 16 or 8 channels. Each channel of the 41-761 provides a low voltage output across two connector pins capable of providing ±20mV with 0.7μV resolution, ±50mV with 1.7μV resolution and ±100mV with 3.3μV resolution, covering most thermocouple types.
-
Product
Canister Load Cell
-
Futek Advanced Sensor Technology, Inc.
FUTEK provides a wide range of Canister Load Cells designed for high capacity compression applications. These models offer robust construction with a capacity range beginning
-
Product
Single Point Aluminium Load Cell
EST-5
-
Technopark Automation & Control
The EST-5 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 600 x 600 mm. This load cell is available in capacities 50 kg and 100 kg.
-
Product
Industrial Weighing - Wireless Load Cells
-
A wireless industrial weighing scale system can be advantageous, for instance when running conduit for cable is impossible, or if the cable could be damaged easily. In some cases the wireless interface is more economical than long runs of cable. These systems can be battery operated or hard wired to a power source if available. View our wireless load cell options below.
-
Product
Load Cell
-
Precise and robust and it has been designed to meet the requirements of a wide range of industrial weighing applications: hoppers, tanks, platforms. Is able to work in severe environmental conditions typical of applications in food, chemical and pharmaceutical industries.
-
Product
S-Type Load Cells
-
S-Type load cells are low-cost and high performance side mounted load cells suitable for a number of weighing and general force measurement applications. They come with a 6-foot strain relieved integral cable with pigtail leads that are stripped and tinned for electrical interface.
-
Product
Load Cells
-
An array of load cells, including bending beam, tension and compression link, button, low profile, through hole, S type, cannister, tension link, and single point load cells as well as load pins.
-
Product
Bi-axial Dynacell Load Cells
2527 Series
-
During tests carried out on servohydraulic machines, elements of the system are subject to acceleration. As a result, in addition to the force applied to the specimen, the load cell also reads forces resulting from its own movement and the mass of the grips and fixtures attached to it. Dynacell is the world's first truly dynamic load cell, designed from the outset for measuring dynamic loads. Dynacell introduces the following advantages:*Reduces dynamic load errors which can be a significant percentage of reading *Increases productivity by allowing higher frequency operation while maintaining test validity *Improvements such as doubling the frequency are common
-
Product
Solar Array Simulator
-
Among other things, solar array simulators are required for testing satellite power supplies. An SAS (Solar Array Simulator), consisting of an interconnection of several Solar Array Simulator modules, maps the solar panels and displays the individual strings connected in parallel. Optionally, the individual SAS modules are monitored by a Second Level Protection, so that the test object is not damaged in case of errors with the voltage sources. Additional circuitry is implemented via project-specific test modules. The signal path to the DUT can be separated, e.g. for dynamic current measurements.The Keysight Solar Array Simulators used were specially developed for satellite applications and cover the significantly higher requirements regarding the control speed of MPP tracking compared to terrestrial applications.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, 750 V Isolation
43-752A-011
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
-
Product
UV Range Simulators
-
Textron Systems' operational range systems deliver the same rich, high-fidelity environment enjoyed in systems integration laboratories and on flight lines to training ranges for seamless interoperability and maximized training outcomes. Our modular design allows easy configuration of a multispectral system for training and test to support advanced sensor fusion.
-
Product
Low Profile Compressive Load Cell
CCLP-1.0
-
Low Profile Compressive Load Cell – 0.5t to 20t
-
Product
Mini Load Column Load Cell Compression Only with Mounting
MLC SERIES
-
The MLC Series is our miniature high capacity compression only load cell/force sensor, featuring low profile compact size for a wide range of portable and dedicated applications up to 30,000 lb The load diameter is slightly convex for accurate load distribution. Low deflection through design results in ultra fast frequency response. The MLCs are designed to be mounted in a shallow machined flat pocket or smooth flat surface, either free or fastened via a bottom 6-32 tapped hole. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial Environments.
-
Product
Load Cells & Force Transducers
-
BLH and Nobel Weighing Systems offer a wide variety of load cells and force transducers, ranging from the unique KIS load cell and weigh module to the VPG transducers range of products. Our many years of experience, our state-of-the-art instruments, and the exceptionally broad range of components that go into our systems allow us to deliver high-quality solutions tailored to your needs.
-
Product
Solar Cell Simulation
Setfos
-
Setfos excels in analyzing and fitting experimental data, providing researchers with valuable insights and trend predictions. Complement your experimental work with Setfos for unmatched accuracy and reliability in data interpretation.
