Conformance
assures device performance within a specific range of requirements.
See Also: Performance Testing, Compliance
-
product
PXI Source Switching Module
40-618-001
The 40-618 PXI Source Switching Module consists of 12 separate 4-channel multiplexers and 44 uncommitted SPST relay contacts in a single width PXI module. Typical applications include signal routing for avionics test systems that conform to the ARINC 608A specification.
-
product
6-Port PCI Express
PEX 8624
The ExpressLane™ PEX 8624 device offers 24 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 6 flexible ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The 24-lane switch enables users to add scalable, high bandwidth, non-blocking interconnection to a wide variety of applications including workstations, communications, storage, and embedded systems as well as intelligent I/O modules and add-in cards.
-
product
NVMe-oF
NVMe/oF adoption is rapidly increasing and full NVMe specification conformance over Ethernet networks or Fibre Channel fabrics requires the ability to validate transactions over all transports.
-
product
Grid Simulators
A grid simulator can be used to simulate the characteristics of low-voltage mains. For this purpose, all voltages and frequencies of the supply networks occurring worldwide can be simulated. Critical states such as short-term voltage dips or voltage peaks (surge/burst) can also be generated.The integrated sequencer function enables the generation of different network parameters, e.g. distorted waveforms and intermediate oscillations. Therefore, grid simulators are well suited for testing conformity to standards and especially for determining the behaviour of electrical equipment in borderline situations. Many European and other international standards are pre-programmed for testing.
-
product
USAF Targets
These targets conform to MIL-STD-150A. Frequencies change by the 6th root of 2. This target is also available in custom sizes and contrasts. This test target meets requirements as specified in MIL-STD-150A for resolving power tests. The target consists of a series of Elements having two sets of lines at right angles. Each set of lines consists of three lines separated by spaces equal to the line width. Each bar has a length to width ratio of 5:1. (Line width is equal to one half of line pitch, which is the inverse of line frequency.) Elements are arranged in groups of six each and Groups are arranged in pairs. Even numbered Groups occupy the left side and bottom right corner and contain a square feature having and edge length equal to the line length of Element 2 in that group. Odd numbered Groups occupy the top right corner and side. Groups and Elements are labeled and differentiated by numbering adjacent to their features. Frequencies in cycles/mm (c/mm) increase between each Element by the sixth root of two (approximately 12.25% per step). The general formula for the line frequency of any target Element can be expressed as 2Group+(Element-1)/6.
-
product
Household And Commercial Appliance Testing
Product Safety Consulting Inc.
Product Safety Consulting guides you through the process of obtaining safety certification in the fastest time and for the least cost. We have years of experience testing products according to multiple UL/IEC Standards. We help you not only verify the classification of your appliance, but get you through the conformity assessment process – from designing for compliance, to applicable essential requirements, to testing your product, to achieving certification.
-
product
3-Port PCI Express
PEX 8613
The ExpressLane™ PEX 8613 device offers 12 PCI Express Gen 2 (5.0 GT/s) lanes, with support for 3 ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The 12-lane switch enables users to add scalable, high bandwidth, non-blocking interconnection to a wide variety of applications including workstations, communications, storage, and embedded systems as well as intelligent I/O modules and add-in cards.
-
product
Power Supply 1950W
PS236 / CS236 1100W
The high density high sophisticated PS236 power supply series replaces the well used PS336 types. PS236 is only 3U high and features six separately regulated extremely low noise outputs for use in CAMAC crates conforming EUR 4100 as well as CERN EP82-01 / EP84-01 and 46-04 specifications as well as in NIM bins UEN01 HC 12.
-
product
Impedance Stabilization Network
Beijing KeHuan Century EMC Technology Co,.LTD
KH8158 is a device for measuring the common mode interference voltage of unshielded twisted pair cables. Cable testing according to CISPR 16-1-2. The equipment under test (EuT) and auxiliary equipment (AE) are directly connected to the corresponding ports. The port adopts RJ-45 socket (the distribution conforms to T568A/B.) This equipment is divided into three specifications: CAT3, CAT5, and CAT6, and the corresponding equipment is selected according to the cable model.
-
product
Automotive Ethernet Test Fixture
AE6941A
The AE6941A automotive Ethernet electrical test fixture provides easy access to automotive Ethernet electrical signals so you can perform conformance testing and device characterization quickly and easily.
-
product
Motor Vehicle Testing Instruments
Foshan Analytical Instrument Co, Ltd.
Possess all manufacturing technology and independent intellectual property right. It conforms to international standards such as OIML R99 and ISO3930Class I. It meets the requirement of dual idle instrument ofGB18285-2005.HC、CO、CO2 are measured by NDIR method and O2，NO are measured by electrochemistry method. Highaccuracy, with automatic compensation for pressure and temperature. With high stability and autom-atic zeroing, there is no need to frequentlycalibrate it with standard gas.It can be used to measure the vehicle using LPG,CNG and alcohol as its fuel,It can be powered by the vehicle battery for the mobile testing station (By using additional power converter,optional part).With bigLCD screen,built-in printer,it has an automatic recording and testingfunction.The rotating speed can be measured viathe cigarette lighter or battery.The two/four gas analyzer can be upgraded to fivegas analyzer.
-
product
Unclamped Inductive Load Tester
ITC75300
The ITC75300 is a 400 amp version of the ITC75100 which performs ruggedness testing of power MOSFET’s, IGBT’s and diodes that conforms to MIL-STD-750 method 3470 by stressing them to controlled energy levels, accomplished by the devices driving an unclamped inductive load. Improved Test Specifications allow complete control of test parameters.
-
product
Compliance Testing Services
We offer testing for compliance across many of the standard specifications. Austin Labs also creates custom conformance programs for many of our partners to help them address gaps in testing coverage. These compliance capabilities include full automation of tests suites to allow for standardized pass/fail testing.
-
product
9U CTEL Backplanes with system Slot on left 9U8Slot, 3 x P47
103CTEL908-4146R5
Conforms to PICMG basic specification 2.0 R3.0, Versions conforming to PICMG H.110 Computer Telephony specifications, 8-layer and 12- layer controlled impedance stripline design.
-
product
Repeat Durability Tester
TIQ1000
It is a device to measure repeated endurance such as limit bending test of board, endurance test of mounted board, endurance test of connector, etc. Continuity data and load data can be obtained during the cyclic endurance test. Conforms to JEITA ET-7407 "Environmental and durability test methods for mounted CSP/BGA packages".
-
product
Electrical Receiver Conformance Test Application for IEEE 802.3bs/cd
M8091BSCB
IEEE 802.3bs receiver test application for 200GAUI-4 and 400GAUI-8, covering chip-to-module, chip-to-chip, backplane, and copper cable interconnects.
-
product
Friction and Wear Tester
EFM-III Series
The EFM-III series is a friction and wear tester for tribology evaluation in conformity with JIS K 7218. This tester is designed for scientific elucidation and technical evaluation of the characteristics relating to sliding friction, wear and lubrication, that are surface behaviors of relative properties of two interacting material surfaces (relative properties of solid materials in relative motion).
-
product
Loop and Line Powered Level Switch
Safety IntelliPoint
The Safety IntelliPoint level switch provides a capacitance probe level switch with either a current output or relay contacts and “On-Board” self-diagnostics to ensure reliability. This SIL Intellipoint conforms to SIL 2 specifications providing the ultimate in level switch integrity and level sensing elements for a wide variety of temperatures, pressures, and materials.
-
product
Coaxlink Duo PCIe/104-EMB
Ruggedized board for industrial and transportation embedded applicationsSmall stackable PCIe/104 form factorExtended temperature range: -40 to +85°C / -40 to +185°FSustained shock: 40 g/11ms (all axes - half-sine and saw tooth)Optional conformal coatingTwo CoaXPress CXP-6 connections: 1,250 MB/s camera bandwidthPCIe 2.0 (Gen 2) x4 bus: 1,700 MB/s delivery bandwidth
-
product
MIL-STD-1553 XMC Interface Module
XMC-1553
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurations - Transformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating availableDesigned for extended temperature operations - x1 Lane PCI Express Host Interface - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Flexible Multisensor Probes
IT Series
Physitemp multisensors are made with our specially manufactured thermocouple wire. We test and grade this wire to standards better than the accepted ''Special Limits of Error'' and guarantee 0.1°C accuracy in the range of 0-50°C . All multisensor probes conform to NIST standards. These multisensor probes are custom-made and should be ordered to your requirements on number of sensors and spacing between sensors.
-
product
Atec Series 7
TEC® Series generic purpose test benches are used by most airlines, systems manufacturers and MROs (Maintenance, Repair and Overhaul) companies to guarantee the conformity of critical electronic equipment. Available on all continents, the ATEC® Series can be adapted to suit various needs owing to its modular nature and capacity to test almost all airliner LRUs. SPHEREA has the world’s largest testing library.
-
product
LXI Single 32 Channel Fiber Multiplexer FC/APC, Single-Mode
60-850-014
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
product
Wireless Sensor Tags & Interfaces
NFC and UHF RFID sensor tags offer a highly integrated solution for remote sensor data logging. The tags conform to the specifications of the NFC/ISO15693 as well as the UHF RFID standards. Featuring on-chip temperature sensing and the exclusive cool-Log™ technology, these sensor tags enable innovative and cost-sensitive solutions in food and pharmaceutical cold-chain management, industrial process control, remote monitoring and healthcare applications. NFiC™ ICs from ams lower the barriers to NFC integration in electronic devices thanks to their small footprint, high data rate, flexible data transfer modes, fully passive NFC tag emulation and advanced energy harvesting. NFC/HF interface tags are best suited to demanding consumer and industrial applications such as zero-power device configuration and set-up, feature-rich contactless cards for payment and authentication, smart toys and connected cars.
-
product
ARINC 429 PMC Interface Module
PMC-429
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx ChannelsProgrammable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application Interface supporting C++, C#, and .net DevelopmentDevice Driver Support: Windows, Linux, VxWorks, and other operating system - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Metal Wire Torsion Testing Machine
WTT Series
Jinan Testing Equipment IE Corporation
WTT series metal wire torsion tester is mainly used in a metal factory to test the plasticity of metal wires and ropes under torsion condition. Surface flaws of steel wires may be shown during the testing process. The revolution is displayed on a 4- digit LED, with the max. revolution value displayed as 999.9. The revolution value is automatically held at the break of specimens. With computer & software, the Metal Wire Torsion tester can realize automatic control. The Metal Wire Torsion tester conforms to standard ASTM A938, ISO7800. The Metal Wire Torsion tester is an ideal QC tool for Quality Inspection & Control Department related to steel wire application.
-
product
Multifunction Data Collection and Analysis System
9000
The Model 9000 DME System is a high performance multifunction data collection and analysis system. It is suitable for application in an electrical utility substation or plant environment to produce Sequence of Event (SER), Digital Fault Recorder (DFR), Dynamic Disturbance Recorder (DDR), and Continuous Recorder data in conformance with PRC-002-1 and PRC-018-1. All data recorded by the DME system is stored in IEEE C37.111 format and named in conformance with IEEE C37.232. The system also has a software option to enable the Phasor Measurement Unit (PMU) feature to provide streaming data in conformance with IEEE C37.118.
-
product
Ohm-Stat Digital Display Megohmmeter
Measures resistivity RTT, RTV, and RTG 103-1012 ohms/sq., ohms, ohm-cmRelative humidity 10% 90% RHTemperature 32oF 100oFDigital display: easy to interpretNIST calibration includedIncludes chair probe to measure smocks, earth ground, chairs, and resistance probes: $400 value for freeResistivity probe built in the bottom of meterProduct conforms to the ESD S.20.20 spec standardsCE mark includedThe kit includes, two (5) lb probes, coil cords, hard carrying case, battery, 110v or 220v adaptor, garment clips, chair probe, and ground circuit tester
-
product
LX-D Shore D Rubber Durometer, Hardness Tester
LX-D
Shenzhen Chuangxin Instruments Co., Ltd.
LX-D durometer is suitable for hardness test of high degree of hardness material, such as common hard rubber, hardened resin, glass, acryl, Plexiglas, thermos plastic rubber, printing plate, fibre, acryl,etc. The product conforms to GB/T531-1999 and other related standard request.
-
product
16-Port PCI Express
PEX 8664
The ExpressLane™ PEX 8664 device offers 64 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 16 flexible ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The 64-lane switch enables users to add scalable, high bandwidth, non-blocking interconnection to a wide variety of applications including servers, communications, storage, blade servers, and embedded systems.
