Interfaces
connections between dissimilar environments.
See Also: Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, Interconnects
-
Product
Artificial Power Network
KH3765
-
Beijing KeHuan Century EMC Technology Co,.LTD
The KH3765 artificial power supply network is equipped with the receiver produced by our company to conduct large current conduction interference test. The frequency range of this product is 150KHz-30MHz , the current is 50A , and the AC frequency can reach 0-400Hz . It is widely used and convenient to switch. Compared with similar products on the market, it greatly reduces the operation steps and buys valuable time for your rectification work. This product also provides a standard10AThe interface makes your test more convenient. Meet the requirements of GB-6113 for power supply network.
-
Product
Precision Voltage and Current Sources
VI-700
-
The VI-700 Voltage and Current Source is a versatile precision dialable or remotely programmable voltage and current source. Its three ranges provide up to 20 V full scale (200 V with the HV option), and down to 100 mV resolution; and 20 mA full scale down to 0.1mA resolution. Both voltage and current outputs are available simultaneously. The output is set by a range selector and thumbwheel switches in the LOCAL mode, or by a digital input at the rear panel. The REMOTE mode control can be a RS232 or IEEE-488 interface.
-
Product
Interface Units
-
intelligent, microprocessor controlled, data acquisition and lambda measurement unit for up to 6 wide band UEGO sensors. It is based on the sensor node and can be used as part of the DATA
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Ferrules, 0.5m
A050DM5-F-0A050
-
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Programmable Video Signal Generator
VG-871B
-
The VG-871B is a standalone type multiple-interface video generator, which can test most of Flat-Panel-Display in current market. It supports the HDMI digital interfaces with the latest standard Ver.1.3a, and also supports specific functions of HDMI 1.3a such as Deep Color (max.12-bit), xxYCC and LipSync
-
Product
Digital Power Meter (High Accuracy Model)
LS2050
-
LS2050 digital power meter is a new generation intelligent product which adopts digital sampling technology to analysis of the waveform. It has the following features: • Three windows digital display which reduces reading error, intuitive and convenient • Adopts high speed MCU and high precision A/D to control and measurement • All measured data as virtual value, also suit to signal waveform distortion • Fast test • Equipped with RS232 communicate function, can use upper computer software to carry on remote operation, control and read corresponding data, the test data and waveform could be displayed in the PC, Chinese and English operation interface, high intelligent instrument • This instrument provides two kinds of method to calculate total harmonic distortion (THD), IEC and CSA.
-
Product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 580 x 250 mm (wxd)
CMCSK-03-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
PCIe/104 OneBank FPGA I/O Board
EMC²-7A200
-
Sundance Multiprocessor Technology Ltd.
The EMC2-7A200 can use commercial, industrial or automotive graded Artix-7 FPGAs and is complimented with 1Gbyte of DDR3 local storage, 32Mbytes of Flash memory for storage/configurations and has 68x free differential I/O pins which are routed to a VITA57.1 FMC-LPC high-speed connector for bespoke interfaces.
-
Product
AXIe High-Speed Digitizer/Wideband Digital Receiver, 12-bit, 3.2 GS/s, 8-ch, FPGA Signal Processing
M9703B
-
Based on the AXIe standard the M9703B is an 8-channel, 12-bit digitizer/wideband digital receiver, able to capture signals from DC up to 2 GHz at 1.6 GS/s. A channel interleaving capability allows waveform acquisition at up to 3.2 GS/s with exceptional measurement accuracy. The M9703B also provides real-time data processing, large FPGA and customizable I/O interfaces. Detailed explanations can be found in the firmware options section of the datasheet.
-
Product
GPIB-ENET/1000 , Ethernet GPIB Instrument Control Device - Universal Euro 240VAC
781630-04
-
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Basic AC Power Source, 500 VA, 310 V, 2.5 A
AC6801B
-
Easily access setup and measurement information This basic AC power source offers stable, reliable power up to 500 VA. An intuitive user interface and flexible I/O connectivity.Increase your uptime with stable, reliable AC power sourceEngineer reliability into your designs with a basic AC power sourceTest your designs with confidenceTest under real-world conditions - fluctuating voltage or transient spikes
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Ferrules, 2m HV, Exit Away From Pin 1
40-972-050-2m-MU-HV
-
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
19" Breakout Panel for Ethernet, USB & DisplayPort
Cabinet CP-101 & CP-102
-
The CP-101 & CP102 are breakout panels which are used to provide a clear connection interface for 19” racks. They are equipped with the most common interfaces found on industrial computers. Both variants feature the same connectors, but distinguish in cable length (1m for CP-101 and 2m for CP-102).
-
Product
µModule Isolated Transceivers
-
Analog Devices µModule (micromodule) isolated transceivers provide robust galvanic isolation for digital serial communication interfaces, including SPI, I2C, RS-485/RS-422, RS-232, and USB. Isolation barriers are implemented using Ethernet transformers, coupling capacitors, or embedded inductors. All devices are simple to configure, have very low EMI susceptibility and emissions, and feature high noise immunity to preserve signal integrity.
-
Product
Seat Actuation Systems
-
Extensive solutions for seating cabin interiors including motion and lighting controllers, linear and rotary actuators, power supplies, passenger interfaces, custom harnesses, sensors, pneumatic units, and bladders.
-
Product
Cable Assembly, 200-Pin LFH, Female (Female Screwlocks) to Unterminated (Tinned Ends), 0.5m
40-972B-200-0.5m-FU
-
This female rear exit to unterminated 0.5m long cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, unterminated with tinned ends. The connector assembly can be secured to its mating connector by female screwlocks.
-
Product
Wire Harness Tester
Panther4HT Master- Slave DSU
-
Qmax Test Technologies Pvt. Ltd.
The Master- Slave DSU based Panther4HT Wire Harness tester is designed for testing and verifying electrical connections in a cable, harness, backplane or any other wired assembly. It offers unique Qmax MASTER - Slave concept and SATELLITE UNIT Options to avoid looping back of cable to the ATE. All Satellite Units communicates the measurements through LAN interface which is very useful for on-board applications in Aircrafts / Ships and similar applications where large cable looms are used. This innovative concept will eliminate the long adapter cables and hence storing, maintaining and re work of these kind of cables are avoided. Furthermore single Master Controller Unit (MCU) is used to control not only all the satellite units , but also communicate with all satellite units through Ethernet Communication port. A single reference Cable is used to link the all the satellite units with the Master Controller in controlled loop manner is a value add to the product.
-
Product
Data Acquisition and Logging, Multimeter System
DAQ6510
-
Creating a new level of simplicity, the DAQ6510 has a touchscreen user interface that enables faster setup time, real time monitoring of test status, and detailed data analysis on the instrument. See all digital multimeters »
-
Product
PCI-8511, 2-Port, Low‑Speed/Fault-Tolerant CAN Interface Device
780682-02
-
The PCI‑8511 is a fault-tolerant controller area network (CAN) interface for developing applications with the NI‑XNET driver. The PCI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
Photocurrent Meter
I 520
-
display range 0.01 nA (last digit) to 7 999 μA4-digit display (0-7999) with dimmer for brightness controlV.24-(RS 232-) Interface, analog outputranging auto/manual or remote programmableapprox. 2.5 readings/s, attenuator 100% to 0dark current compensationpower supply for thermostatic stabilized LMT photometer headspower supply 230 V, 50-60 Hz, power cable with Euro plug
-
Product
PCIe-8510, 2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device
785325-01
-
2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device—The PCIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PCIe‑8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
Mini-ITX Embedded Board with 8th/9th Gen Intel® Core™ i7/i5/i3 Processors
AmITX-CF-I
-
The AmITX-CF-I is a Mini-ITX motherboard supporting the 8th/9th Gen Intel® Core™ i9/i7/i5/i3, Pentium® and Celeron® processor in the LGA1151 package, and the Intel Q370/H310 chipset. The AmITX-CF-I is specifically designed for customers who need high-level processing and graphics performance with a long product life solution. This model supports ubiquitous high-speed data transfer interfaces PCIe 3.0, USB 3.1 Gen2 and SATA 6 Gb/s (SATA III), with dual-channel DDR4 2400/2666 MHz non-ECC memory up to 32 GB in two SODIMM slots. The AmITX-CF-I features DVI, DP and HDMI ports, LVDS header, dual Gigabit Ethernet ports, USB 3.0 ports, USB 2.0 ports, SATA 6 Gb/s ports, and audio with Line-out, Line-in and Mic-in connectors. Expansion is provided by one PCIe x16, one M.2, and one mini-PCIe slot. The onboard pin header provides GPIO, USB and RS-232 support. The board is equipped with SPI AMI EFI BIOS, supporting embedded features such as hardware monitor and watchdog timer.
-
Product
INERTIAL MEASUREMENT UNIT
MS-IMU3050
-
Extreme performance in the industry's most compact package, the ITAR free and EAR99 MS-IMU3050 represents the next generation of cutting edge MEMS IMUs. With an ultra-durable and dimensionally stable MIC-6 alloy housing, MIL-A-8625 coating, and Mil-Standard interface connector, the MS-IMU3050 will endure the most demanding environments, giving long term stability and reliability in your application.
-
Product
NITOS Wireless Sensor Platform
-
The NITOS prototype wireless sensor mote, is comprised of open-source and configurable modules. NITOS mote features the ATmega32u4 microcontroller running at 8MHz and operating at 3.3V. The aforementioned microcontroller is fully compatible with the Arduino platform that enables ease of software development and provides compatibility with several commercial sensing modules. Moreover, the platform is equipped with an Xbee radio interface that enables communication with the respective gateway. The Xbee module is a tiny device ideal for setting up mesh networks and has a defined rate of 250 kbps. This module uses the IEEE 802.15.4 stack which is the basis for theZigbee protocol. Apart from the Xbee module, NITOS mote can also feature a WiFi wireless interface in order to communicate with WiFi gateways. The developed mote currently features specific sensing modules, an air temperature and humidity sensor, a light intensity sensor and a human presencesensor. Various types of sensing modules and actuators can be further integrated exploiting existing Arduino software that implements several existing communications protocols. The firmware can be easily uploaded through the on-board USB connection. Figure 1 illustrates the developed NITOS mote and the respective gateway node.
-
Product
PCI Express 8-Port
7804ec
-
The 7804ec PCI Express serial interface provides eight multifunction serial ports, each individually field-configurable for RS-232, RS-422, or RS-485. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates to 230.4 Kbps (RS-232) and exceeding 1 Mbps (RS-422/485).
-
Product
LXI/USB 18-Slot Modular Chassis
60-103D-001
-
The 60-103D is an 18-slot LXI/USB Chassis fully compliant with the LXI Standard 1.4 and allows the large number of our 3U PXI modules to be installed and controlled through a standardized Ethernet interface or via a USB interface. Each module is supported as though it is an LXI compliant device, complete with a driverless soft front panel that provides control of the module functions.
-
Product
PCIe-6535B, 32-Channel, 10 MHz, 40 MB/s Digital I/O Device
782629-01
-
The PCIe-6535 can continuously stream data over the PCI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
Product
Fuel Flow and Torque Converter
Model 44SM1
-
This self-contained, remotely mountable Second Harmonic Fuel Flow Interface accepts data from a second harmonic fuel flow transmitter then converts this information into a frequency output proportional to fuel flow. In addition, this module will accept signals from a T56 Torque Tranducer and provide a DC voltage proportional to Torque. Typical application is for use with Flight Management and Nav Management Systems. The use of field proven designs and carefully selected components assures high reliability field performance.
-
Product
26-Pin D-Type Male Straight PCB Mount
40-963-026-SM
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
4-Channel 200 MHz, 16-bit A/D with Virtex-6 FPGA - 6U VPX
Model 57660
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 200 MHz 16-bit A/Ds- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
