Interfaces
connections between dissimilar environments.
See Also: Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, Interconnects
-
product
Quad M Module Carrier
DP-cPCI-5112
DP-cPCI-5112 provides a compact high performance cPCI bus gateway to four ANSI approved M-Module Interfaces. This is a non-intelligent 6U form factor M-Module Carrier board. The DP-cPCI-5112 allows a flexible I/O solutions to be implemented in the carrier board. The M-Module carrier board occupies single slot in a CompactPCI system. Different mix and match of various I/O solutions will simplify the job for system integrators.
-
product
68-Pin SCSI Micro-D Connector, Female
40-961-068-F
This connector is designed to allow users to directly terminate with IDC connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
product
1-Ch. 6.4 GHz or 2-Ch. 3.2 GHz A/D, 2-Ch 6.4 GHz D/A Kintex UltraScale - 3U VPX
Model 52141
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Supports VITA-49.2 VITA Radio Transport standard- One-channel mode with 6.4 GHz, 12-bit A/D- Two-channel mode with 3.2 GHz, 12-bit A/D- Programmable DDCs (Digital Downconverters)- Two 6.4 GHz, 14-bit D/As- Programmable DUCs (Digital Upconverters)- 5 GB of DDR4 SDRAM- µSync clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
4-Channel DAC FMC Module
SMT-FMC211 – LPC
Sundance Multiprocessor Technology Ltd.
The main component of the SMT-FMC211 is the Texas Instruments 4 channel DAC – TI’s Quad 1.25GHz DAC3484. This device offers excellent SFDR performance better than 70dBc, with an output sample rate of over 312MSPS. It interfaces to an Artix-7 XC7A15T-2C FPGA using a 16 bit differential DDR bus.
-
product
4-Channel 200 MHz, 16-bit A/D with Virtex-7 FPGA - 3U VPX
Model 52760
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four 200 MHz 16-bit A/Ds- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
LXI Optical Switching
LXI is an ideal platform for supporting optical switching systems; the use of Ethernet control makes it easy to provide optical switching within the network that is easy to control via a programmatic or web based interface. MEMS switch technology offers higher performance and longer operational life compared to conventional prism based optical switching.
-
product
Remote I/O
ADLINK remote IO and serial communication cards are suitable for handling multiple digital signal types for IoT and other industrial applications such as facility monitoring, environmental monitoring, and industrial process control.Remote IO - NuDAM modules provide direct communication with various sensors, including performing signal conditioning, scaling, linearization and conversion to obtain temperature, pressure, flow, voltage, and current measurements. The new ND6100 series modules use Modbus/RTU remote data transmission protocols, providing customers with a comprehensive product portfolio. ADLINK's serial communication cards provide a PCI/PCIe interface and support RS-232 and CAN communication interfaces, allowing customers to choose the most suitable communication card for various automation equipment needs.
-
product
Probing Solutions
ES62X-CMPS
The ES62X-CMPS compact manual probe station is a rugged wafer probing solution designed for high reliability, compact size and low investment cost. It enables manual wafer level measurements up to 300 mm wafers. The probing station can also be used for TLP, HMM, HBM, LV-Surge, RF, S-parameter and DC-measurements. Micro positioners with vacuum as well as magnetic base can be attached. The chuck has a vacuum interface for the wafer and is electrically isolated. Multiple 4 mm connectors can be used to connect a voltage potential to the wafer backside.
-
product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Ferrules, 1m
A050DM5-F-0A100
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
OEM 1-Channel Fiber Optic Signal Conditioner PCB Module
FOTEMP1-OEM-MNT
The FOTEMP1-OEM-MNT is a small form factor PCB interface module designed for low cost insertion of high precision GaAs-based fiber optic temperature sensor technology into OEM applications where common electrical temperature sensors and thermocouples cannot be used. The OEM interface product is compatible with all TS series fiber optic temperature probes. The sensors are entirely non-metallic and electrically passive, providing immunity to EMI, RFI, MR, microwaves and radiation is required.
-
product
4-Channel 200 MHz, 16-bit A/D with Virtex-6 FPGA - 6U VPX
Model 57660
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 200 MHz 16-bit A/Ds- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 5-Bank 26.5GHz SMA
60-801-305
The 60-801-305 is a 6-channel, 5-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
Laser Source
TW3108
Techwin(China) Industry Co., Ltd
Laser Source TW3108 is designed specially aim at users with high requirements. With featuers of durable structure, large LCD display with backlight and friendly operation interface, the TW3108 advanced stability handheld optical light source provides a lot of convenience for your field work. High stability of output power and quite stable output wavelength, it is an ideal instrument for optical network installation, trouble shooting, maintenance and other optical fiber related systems.
-
product
PCIe High Bandwidth Cameras
Cameras with PCI Express interface stand out through extraordinary fast speed based on the throughput of 20 Gbits for Gen 2 and 64 Gbits for Gen 3. The whole range of models offers DMA (Direct Memory Access) and data transfer to GPU possible on Linux. This helps with extremely low latency.
-
product
Scalable Microwave Subsystems with Open-Architecture Ethernet/LXI Platform
EX7000 Series
The EX7000 family is the industry’s first series of scalable microwave subsystems built on an open-architecture Ethernet/LXI platform. This innovative family of products simplifies the development of custom RF Interface Units (RFIU) requirements with its common hardware platform and software communications interface, while maintaining the look and feel of a standard COTS product.
-
product
Fiber Tranceivers
Wuhan Sunma Technology Co., Ltd.
Active Optical Cables, Fiber Optic Transceiver Module is a self-contained component that can both transmit and receive. Usually, it is inserted in devices such as routers or network interface cards which provide one or more transceiver module slot (e.g GBIC, SFP, XFP).
-
product
SIP-90-4 Test System Interface Probe
SIP-90-4
Overall Length (mil): 693Overall Length (mm): 17.60Rec. Mounting Hole Size (mil): 57Rec. Mounting Hole Size (mm): 1.45Recommended Drill Size: 1,45 mm
-
product
Dual Pitot Tube Flow Meter
PTFM-ONE-DT
The Dual Pitot Tube Flow Meter, PTFM-ONE DT is a standalone interface for measuring exhaust gas flow rate of combustion engines. The system uses the tried-and-tested pitot tube principle with high-frequency transducers, with a sampling rate of 1kHz to accurately measure highly pulsating exhaust flows. This rapid capture rate ensures that any pulsations or exotic behaviour caused by the engine is measured, and the unique design of the PTFM-ONE DT means reverse flows can be calculated, with the same guarantee of sensitivity.
-
product
Potentiometer for OEMs
FlexiPot
The best user interface, whether in consumer electronics or industrial controls, contains sensors that cause minimal interference, meaning the user may not even know they are there. FlexiPot, by Tekscan, is a flexible membrane potentiometer with an ultra-thin (0.008"), lightweight profile. Low power requirements combined with a linear output make it the ideal position sensor, from both a manufacturing perspective as well as a user perspective.
-
product
Waveform Generation Toolbox for Wideband Signal Simulation
N7509A
The Waveform Generation Tool provides a simplified interface for baseband modulation of Keysight's wide bandwidth signal simulation solutions, for signals with up to 1 GHz RF bandwidth. Even the most complex signals are defined and implemented easily through the software interface. Signals can be defined through basic parameter entry or from files created in MATLAB or other engineering environments. For each selection in the main menu, a subsequent screen appears, enabling the user to enter the parameters required to define the waveform and invoke the built-in calibration routines. A display on each sub-panel shows the ideal frequency domain waveform calculated from entered parameters. A simulation mode is provided to enable development and operation without connection to the instrument hardware.
-
product
Basic AC Power Source, 4000 VA, 310 V, 20 A
AC6804B
This basic AC power source offers stable, reliable power up to 4000 VA. An intuitive user interface and flexible I/O connectivity.Increase your uptime with stable, reliable AC power sourceEngineer reliability into your designs with a basic AC power sourceTest your designs with confidenceTest under real-world conditions - fluctuating voltage or transient spikesEasily access setup and measurement information
-
product
Capacitor Leakage Current Meter
DU2316/2317
Delta United Instrument Co., Ltd.
Leackage Current range display: 0.0001uA ~ 20.00mAAutomatic or Manual trigger with CHARGE/TEST/DISCHARGE100 sets of memory, can be saved test parameter and comparator setting, easy to use.Cover up free, system firmware upgrade can be update via RS-232, easy to maintenanceHi / Lo current limit setting & PASS/FAIL judgment240*64 Graphic LCD display, can be read the reading clearly and easier.User friendly programmable interface, easy to useProvided RS-232C and Handler combinatorial interface option, to meet your needed
-
product
8-Ports Gigabit Ethernet RCV Interface (R)
YAV90058
8x RJ45 LAN connectors to VPC RCV 192 pins module.
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 12-Bank 18GHz SMA
60-801-212
The 60-801-212 is a 6-channel, 12-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
InfiniiMode Active Differential Probe, 6 GHz
N2752A
The N2752A InfiniiMode differential probe is a new generation of low-cost differential active probes compatible with Keysight InfiniiVision and Infiniium oscilloscopes’ AutoProbe interface. It comes with new operation modes and convenient measurements of differential, single-ended, and common mode signals with a single probe tip, without reconnecting the probe to change the connection. The N2752A probe’s InfiniiMode provides the following modes of operation.
-
product
Software
Easy to use and intuitive software is fundamental in order to analyze complex embedded software challenges. With the increase in use of multi-core SoCs, complex operating system environments, such as AUTOSAR, and the need for hypervisors, iSYSTEM aims to deliver a user interface that provides fast and clear results so that development decisions can be made quickly. Our offering can be broken down into a few core elements:
-
product
LXI Microwave Multiplexer, 50Ω Dual 18-Channel 6GHz SMA
60-891-019
This LXI Microwave Multiplexer is controlled through an LXI interface based on 1000Base-T Ethernet. This provides a quick and easy method of installation. It also provides a simple way of controlling it at a remote location through its API or built in soft front panel.
-
product
SD Card V.4.1 & UHS-II PHY
SD 4.1 Total Solution
To meet the ever increasing data transfer rate in high end applications, such as professional broadcasting transmission or advanced high resolution display, the SD 4.1 specification calls out the maximum performance of 1.56 Gbps at UHS-II full duplex mode per lane or half duplex UHS-II at 3.16 Gbps. In real applications, due to the system overhead and different SD 4.1 device controller designs, the actual measured performance can vary dramatically from system to system. With the newly introduced ADMA 3, the OS driver is now able to issue multiple read or multiple write commands at once, without having to wait for the SD controller to complete one command at a time. Once the SD host controller has collected multiple commands, it will then manage and complete them without intervention from the host software drive. Thus, the UHS-II 1.56 Gbps interface can be more effectively utilized and maximize the system throughput. This feature can be very useful when running multithreaded applications where multiple applications are constantly updating their status or swapping their contents by writing or reading small chunk of data to or from the memory card.
-
product
Torque Meters
Torque meter is available in two different versions: handheld meters or tabletop meters. Torque meter have a wide range of applications. Handheld torque meter is mainly used for industry while tabletop torque meter is the ideal tool for laboratories. Our Torque meters come with a RS-232 port to transfer torque values to a PC or a portable computer. This is very helpful if you want to save the data and stand the chance to compare what you have measured afterwards. Another possibility is that you aim to do long-term-measurements. There the interface and the software are two very useful features that are given to you.Tabletop torque meters can be equipped with a printer (option). You can also order a ISO calibration certificate as an option. This ensures that the device has been calibrated and works perfectly including a measurement with only small deviances that can still be tolerated and do not influence the product's functions. We can offer you torque meters that can measure up to a maximum measuring value of 500 Nm.
-
product
6 Channel Encoder Input Controller
PCI323
The PCI323 Quadrature Incremental Encoder Interface is designed to interface with up to six quadrature incremental encoders. This is an ideal solution for all applications where several encoders must be connected with a maximum of flexibility and a minimum of overhead.
