Interfaces
connections between dissimilar environments.
See Also: Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, Interconnects
-
Product
Rugged Embedded Multifunction I/O System with 10 GB Fiber Optic & 1 GB Copper Ethernet Switch
NIU3E
-
The NIU3E is a small, rugged, low-power, self-contained multifunction I/O processing system preconfigured with 24-CH programmable Discrete I/O, 8-CH ARINC 429/575, 4-CH CANBus and 2-CH MIL-STD-1553 functions and incorporates an Ethernet switch module that offers four (4) 10GBase-SR multimode fiber optic ports and sixteen (16) 10/100/1000Base-T Ethernet ports. The NIU3E can also be configured with one smart Configurable Open Systems Architecture™ (COSA®) function module. The NIU3E boasts a Dual or Quad Core ARM A53 processor for customer application and I/O and communications management. The NIU3E is configured with two 10/100/1000Base-T (GbE) Ethernet ports and an RS-232 port for maintenance / diagnostic or configuration interface. Ideally suited for rugged Mil-Aero applications, the NIU3E delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
MTM-Bus Tester
PXIe-1149.5
-
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
Product
Eighteen Slot PCXI/PXIe Full Hybrid ABex Chassis with up to PCIe x4 Connectivity on Each Slot
ABex PXIe Rack 18
-
Fully featured 7U ABex chassis with 18 slots. This variant allows maximum flexibility and upgrade possibilities. The 18 slot PXIe/PXI hybrid backplane supports also large-scale embedded PXIe controller that requires up to three additional slots on the left side. In addition, Konrad PXIe embedded controllers or MXI interfaces are supported. The ABex PXIe Rack 18 can be combined with a robust VPC interface system.
-
Product
9050 - 50 Module, 2-Tier Solution
-
The rack mountable 9050 50 Module Receiver is designed to accept 9025 and 9050 ITAs and is ideal for systems with advanced mass interconnect requirements. The 9050 can be adapted to accommodate vacuum or mechanical fixturing. Connector modules can be intermixed for creating custom interfaces ideal for functional and system testing applications.
-
Product
CCIX
-
The CCIX® Consortium was founded to enable a new class of interconnect focused on emerging acceleration applications such as machine learning, network processing, storage off-load, in-memory data base and 4G/5G wireless technology. CCIX is a high performance, low latency interface that is based on PCIe Physical layer, up to speeds of 32GT/s. Teledyne LeCroy provides a range of Protocol Analysis tools to support development and debug of CCIX based devices.
-
Product
PCI 96 Channel TTL Digital Interface
8009
-
The 8009 digital I/O interface provides 96 channels of buffered drive digital I/O emulating 8255 mode zero, which can be utilized for PC based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems. 10K pull-up resistors are included. Optional values are available.
-
Product
Fanless Embedded System With 7th/6th Gen Intel® Core™, Pentium® And Celeron® Processor For Railway And Vehicle PC
UST500-517-FL
-
The UST500-517-FL is powered by the LGA1151 socket 7th/6th generation Intel® Core™ and Pentium® processors up to 65W with the Intel® Q170 chipset. The integrated 16 PoE ports are available in RJ-45 or M12 connectors for IP cameras. It provides a full scope of power protection that includes intelligent vehicle power management technology for ACC on/off delay, shutdown delay, and over/under voltage protection. Enhanced by its robust structure and system design, the UST500-517-FL is able to operate under a wide temperature range from -40°C to +70°C and vibration endurance up to 3 Grms. This transportation embedded box is in compliance with ISO 7637-2 and EN 50155 for mobile surveillance applications. There are 16 Gigabit LAN ports which support 802.3at/af Power over Ethernet with a total power budget of 200W. Its DVI-D, HDMI and VGA interfaces support three surveillance monitors. Furthermore, its external accessible SIM card slot enables users to easily change SIM card for different telecommunication service. With wireless LAN modules, this user-friendly transportation embedded system can real-time transmits the video to the control center. The two built-in or four swappable SATA hard drives are used for mass storage of video files.
-
Product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Ferrules, 2m, HV
40-972-037-2m-FU-HV
-
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Automatic Liquid Interface Tension Meter,Surface Tension Analyzer,Oil Interface Tension Meter
-
Chongqing Assen Power Equipment Co., Ltd
Our HTID-1 Automatic Interface Tension Tester is used to test various liquid surface tension and interface tension based on the ring method that is simple and high accurate, which is widely applied in electric, petroleum, chemical, medicine, food, and teaching filed.
-
Product
Ethernet Cameras
HT Series
-
Our cameras are available with resolutions of 2, 4, 12, and 20 megapixels in monochrome, color, or near-infrared enhanced (NIR) with full frame rates of up to 338fps, 179fps, 84fps, and 32fps respectively (we can also provide taped on glass). As the first 10GigE industrial digital camera series in the world, our HT cameras obtain their high performance from industrial CMOS sensors with Global Shutter technology in combination with the cross-industry standard 10 Gigabit Ethernet (10GigE) interface.
-
Product
Cabling Certification
Versiv family
-
The Versiv family accelerates every step of the certification process. Future-ready design supports copper certification, fiber loss, OTDR testing and hardware upgrades. The revolutionary ProjX management system and Taptive user interface ensures jobs are done right the first time. Analyze test results and create professional test reports using LinkWare management software.
-
Product
Mini OTDR Fiber Optic Reflectometer with VFL OPM Laser Source
MT-1300 Plus
-
Guangzhou Wanglu Communications Co., Ltd.
- Display: 3.5 inch color TFT-LCD screen- Handheld design, light weight and easy operation- Single mode: 1310/1550 nm- Dynamic range: 24 / 22dB (can test about 60 km)- Automatic measurement mode: 1310/1550 nm dual wavelength can be tested simultaneously- Applicable fiber: SM- <8m extra-short event dead zone- Wavelength: 1550nm- Up to 24dB High Dynamic Range- Distance Range: 4,8,16,32,64,128,256km- Pulse width: 3ns-10us- RJ45 cable TDR test & cable sequence test- Optical power meter, Visual fault locator, Laser source- Event Map, can display the length of the link, the type of event point and the position of break point.- USB interfaces, supporting USB stick and printer and direct cable download to PC via ActiveSync- LED light- Built-in friendly-environment lith ium battery with high capacity for over 12 hours of operating life
-
Product
PXI Express Optical FPGA Board
HSS-8324
-
The Conduant HSS-8324 Optical FPGA board provides the user with a hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its 24-lane optical interface. The PXIe interface provides a theoretical maximum throughput of 8GB/s (simultaneous in and out).
-
Product
Rebuilt Testers
-
Lorlin® manufacturers New and Rebuilt Discrete Component Semiconductor Test Systems for Transistors, Diodes, Zeners, Fets, IGBTs, SCRs, Triacs, Optos, Small Signal and Power Semiconductors. We measure, screen, test, analyze, characterize and sort the critical parameters of semiconductors devices including Leakage Current, Breakdown Voltage, Gain, Saturation Voltages, and offer a comprehensive test parameter library with an easy to use Windows based applications software. The systems us a Windows 10® 64-BIT Operating System with a USB 2.0 Interface. Engineering excellence, innovation, creativity and cutting edge technology has made Lorlin equipment well known for testing discrete components.
-
Product
4 GHz, 20 GS/s, 4ch, 100 Mpts/Ch High Definition Mixed Signal Oscilloscope
WavePro 404HD-MS
-
HD4096 technology provides 12-bit resolution up to 8 GHz and 20 GS/s.Up to 5 Gpts of acquisition memory enables detailed viewing of long events.15.6" 1900 x 1080 Full HD capacitive touchscreen.New ProBus2 input supports up to 8 GHz bandwidth and direct compatibility with a wide variety of existing ProBus probes - 50Ω and 1MΩ coupling modes support all input types on a single connector.MAUI with OneTouch user interface for intuitive and efficient operation.Deep toolbox enables and simplifies complex analysis.Intuitive navigation to quickly find important features in long waveforms.Zone Trigger – Simple Triggering for Complex Signals.
-
Product
Lock-in Amplifier
HF2LI
-
The Zurich Instruments HF2LI (high-frequency, 2 inputs) is a digital lock-in amplifier covering the frequency range between DC and 50 MHz. It features 2 physical input channels so that it can replace 2 devices in many measurement setups. The 128-bit digital signal processing delivers superior precision thus boosting both the noise performance and the dynamic reserve. With these unprecedented capabilities, the HF2LI brings lock-in amplification to a new level and enables new applications in a frequency range that was previously tied to analog instrumentation. The computer is connected by a high-speed USB interface, which allows data acquisition at high rates. The HF2LI is delivered with a fully featured graphical user interface and a choice of programming interfaces that greatly add to the usability of the instrument.
-
Product
Dual Measurement Bench Multimeter
1908 Series
-
The battery operation can give more than 35 hours of operation. As well as adding portability to the unit the battery option provides isolation from the mains to aid low level measurement integrity. The USB interface is fully accessible in battery mode, allowing full data logging when used with a laptop pc. The dual measurement display shows the main and secondary reading simultaneously to provide either two parameters of the same signal (eg AC and DC Volts), two different signals (e.g AC Volts and DC current), the result and calculated function (eg value and % deviation), two different units (eg AC Volts and dBm) or the measurement along with the selected range.
-
Product
9-Pin D-Type, Right Angled PCB, Female
40-963-009-RF
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
HIGH VOLTAGE SCR CONTROLLED POWER SUPPLY
xPS Series
-
High Voltage SCR Controlled Power Supply, P/N 18278PSPower Rating: 350 KW.Input: 480 VAC, 3 PH, 60 HzOutput: 0 to 5000 VDC, 70 Amps maxRipple: 2 % approximately at maximum rated voltageConfiguration: 12 pulse externally SCR controlled rectifier systemProtection Devices:Input contactorsOverload relay shutoffInput surge suppressorThermal switchesOutput current limiting resistor (made with 5 Ohm Kanthal heating element)Emergency power shutoffCooling: Each 6 pulse rectifier assembly is cooled by three 10” fansInterface: 4/20 ma converter interface for output voltage and output current to SCR controller.Enclosure: The overall dimension of the unit is (78”H x 38”W x 53”D). It is comprised of two separate enclosures each with dimensions of (78” H x 38” W x 26” D) which are integrated together to form a single enclosure. Each half enclosure has one 6 pulse transformer and one 6 pulse high voltage rectifier.Weight: Approx. 5000 lbs.SCR Controller: The 12 pulse SCR controller is supplied by the customer. We were responsible for the 12 pulses Transformer and 12 pulses Rectifier section. Portability: Unit can be lifted up with a fork lift. It can also be moved around with a 5000 lb pallet jack.Transformer: Two 200 KVA transformers are used to step 480 VAC to 3750 VAC each in a 12 pulse configurationRectifiers: Two 6 pulse rectifier assemblies capable for 5000 VDC and 60 Amps output were used. The high voltage rectifier assemblies are isolated and protected in a fiberglass plenum within the enclosure.Blocking Diode: Each diode of the 6 pulse rectifier consists of 10 diodes in series to offer a blocking voltage of 12000 V (PIV)
-
Product
3U OpenVPX Module Xilinx Zynq UltraScale
VPX3-ZU1
-
Sundance Multiprocessor Technology Ltd.
PanaTeQ’s VPX3-ZU1 is a 3U OpenVPX module based on the Zynq UltraScale+ MultiProcessor SoC device from Xilinx. The Zynq UltraScale+ integrates a Quad-core ARM Cortex-A53 based Application Processing Unit (APU), a Dual-core ARM Cortex-R5 based Real-Time Processing Unit (RPU), a ARM MALI-400 based Graphic Processing Unit (GPU) and an UltraScale+ Programmable Logic (PL) in a single device. It also includes on-chip memory, external memory interfaces, and a rich set of peripheral connectivity interfaces.
-
Product
Atec Dyna
-
Macro-instruments an innovative concept : ultra-simple interface between the test bench and the equipment being tested, Software-controlled macro-instrument, Generic TUA (Test Unit Adapter) incorporated in the bench
-
Product
3 Function Slot MOSA Nano Aircraft Interface Computer (AIC)
NIU3A-AIC-01
-
NIU3A-AIC-01 is a Modular Open Systems Approach (MOSA) Aircraft Interface Computer with low power high performance ARM Cortex -A53 processing. 8 GB RAM, 32 GB SATA Flash, 2 x 10/100/1000Base-T Ethernet.
-
Product
Bit Error Ratio Testers
-
Keysight’s bit error ratio test (BERT) system enables the most accurate physical-layer design verification of high-speed communication and multi-gigabit digital interfaces. Our expert-level support will help you select the high-performance hardware, control software, receiver test, and automation tools needed to help you master your design.
-
Product
Mini USB To 90 Series Interface
J90USBI
-
Use in ITA SideRequired Tripaddle Modules VPC 510108126
-
Product
Load Cell Measurement Interface
LCIC-1106a
-
Industrial Measurement Systems Ltd.
Any application related to weighing or measuring forces is now available in your PC...Stand-alone microcomputer-based interface card requires no other interfacing accessories. Simply connect th
-
Product
Portable Cable/Digital TV RF Analyzer
SLM 1479
-
7” full-color, high-resolution touch screen user interface simplifies complex measurement tasksFull motion video and audio decoding of received channelsDigital RF measurements including average power/level, pre/post BER, MER, noise margin, spectral analysis and constellation
-
Product
Channel Serial Lab versions
-
5.0 GT/s 24-lane, 6-port PCIe Gen2 SwitchAll peripheral slots and CPU slot has PCIe interface Gen2 with x4 width10, 100 MHz clock at each peripheral slot1 PPS clock at each peripheral slotGPS module, navigate down to -162 dBm and -148 dBm coldstartMEMS Digital Motion Sensor with ±6g/±12g/±24g dynamically selectable fullscale, 6D orientation detectionHumidity and Temperature Sensor
-
Product
PXI Quad 6:1 High Voltage Power MUX
40-331-003
-
The Pickering Interfaces 40-331/332 High Voltage Power Multiplexer and Matrix Modules are suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. The 40-331 is available as a single 24:1, dual 12:1, quad 6:1, hex 4:1, octal 3:1 or twelve 2:1 multiplexer, and the 40-332 is available in 12x2 or 6x4 matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
Product
EBIRST 78-pin D-type To 68-pin Female SCSI Adapter
93-006-222
-
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Particulate Instruments
-
Teledyne Advanced Pollution Instrumentation
Teledyne API offers a combination of particulate matter measurements to meet a variety of data quality objectives for regulatory ambient air quality monitoring. All T Series instruments offer two front-panel USB ports, an advanced touch screen full color display, customizable user interface with predictive maintenance alerts, one-touch real-time graphing, and multiple language support.
