Programmable Attenuators
-
Product
13 GHz Programmable Attentuator
PA13
-
This device has low impedance mismatch, high bandwidth, wide dynamic range and is capable of rapid state change. The PA13 can be an attractive alternative to either the manually operated microwave attenuator switches, which are expensive and are switched very slowly, or the relay attenuators which are expensive and wear out quickly.
-
Product
Digital Attenuators
-
Macom Technology Solutions Holdings Inc.
Digital Step Attenuators (DSA)are offered in up to 6 Bit control with lowest step size of 0.5 dB covering DC to 40 GHz. MACOM's DSAs can be controlled with serial and parallel control allowing for best implementation for our customers. These products exhibit low insertion loss and high attenuation accuracy and are offered both GaAs and Silicon (SOI) processes and are offered in both packaged and bare die form factors.
-
Product
PXI Precision Resistor Module 6-Channel, 2.5 to 773k
40-297-043
-
This 6-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 4Ω To 1.51MΩ
50-298-150
-
The 50-298-150 is a high density programmable resistor card with 3 channels which can be set between 4Ω and 1.51MΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Fixed Attenuators
-
In circuits are used to lower voltage, dissipate power, and to improve impedance matching. In measuring signals, attenuator pads or adapters are used to lower the amplitude of the signal a known amount to enable measurements, or to protect the measuring device from signal levels that might damage it.
-
Product
Optical Variable Attenuator
TW3303
-
Techwin(China) Industry Co., Ltd
The Perfect Handhold Tester Series Optical Variable Attenuator TW3303 TW3303 handhold optical variable attenuator is used for continuously variable optical signal attenuation. As the attenuator is used in the laser system for the on-line testing, there, thereforeTW3303 can be used in the digital system of communication devices (such as: PHD, SDH) and also in the system of adopting analog modulation (CATV
-
Product
Programmable Relays
-
You get in one unit 12 Inputs and 8 Outputs relays or transistor. Herewith you can do a lot of bigger scale automation whereas the 10 I/O versions are just to short of I/O’s.
-
Product
Programmable Video Signal Generator
VG-871B
-
The VG-871B is a standalone type multiple-interface video generator, which can test most of Flat-Panel-Display in current market. It supports the HDMI digital interfaces with the latest standard Ver.1.3a, and also supports specific functions of HDMI 1.3a such as Deep Color (max.12-bit), xxYCC and LipSync
-
Product
Manual Step Attenuator, DC to 26.5 GHz, 0 to 70 dB, 10 dB steps
8495D
-
The Keysight 8495D dc to 26.5 GHz manual step attenuator offers exceptional repeatability and reliability. Attenuation is provided in 10 dB steps from 0 to 70 dB. Precision gold-plated leaf springs ensure long life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
-
Product
Voltage Variable Attenuators
-
Analog Devices voltage variable attenuators (VVAs) ensure accurate control for a wide range of applications. Our absorptive VVAs are ideal for designs where an analog dc control signal controls RF signals levels over a 30 dB amplitude range, while our monolithic VVAs feature low insertion loss, high IP3, and wide dynamic range, as well as a balanced topology that delivers excellent return loss.
-
Product
PXI Resistor Module 2-Channel 2R to 65.5k with SPDT
40-293-133
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Coaxial Fixed Attenuator, DC to 67 GHz
8490G
-
Keysight's 8490G precision coaxial fixed attenuators maximize your operating frequency range up to 67 GHz by providing industry-leading attenuation accuracy, coupled with low SWR and a variety of attenuation options to suit your application needs. The attenuator is available in attenuations of 3, 6, 10, 20, 30 and 40 dB. The 8490G is swept-frequency tested to ensure it meets specifications at all frequencies.
-
Product
Optical Variable Attenuator
OVA-50
-
OVA-50 Optical Variable Attenuator can precisely attenuate input optical signals at 1310/1490/1550/1625nm wavelengths and directly output defined stabilized optical signals. OVA-50 is applicable in various testing situations.
-
Product
Programmable LED DC Electronic Load
M98 Series
-
M98 series DC electronic load, as a new generation product of Maynuo Electronic Co., Ltd, is designed for the LED driver application. A special circuit is desiged for the LED driver on the base of the M97XX sereies. Incorporating high-performance chips, the M98XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M98XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 131k Ohm - SPST
50-294-134
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
HVFO10X +/-10V (10x Attenuation) Universal Tip Accessory
HVFO100-10X-TIP-U
-
HVFO10X +/-10V (10x Attenuation) Universal Tip Accessory.
-
Product
PXI 10W Programmable Resistor Module, 2-Channel, 1Ω to 62.1Ω
40-253-011
-
The 40-253-011 is a programmable resistor module with 2 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Programmable Insulation Resistance Tester
-
AllWin Instrument Science and Technology Co., Ltd.
Electrical resistance testingLCD displayOutput Voltage: 1.0V~1000VThe insulation resistance range:100kohm to 100Gohm
-
Product
PCI High Density Resistor Card 6-Channel, 24-Bit, 0 To 16M Ohm
50-295A-121-6/24
-
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Programmable Limit Switch (PLS)
-
AMETEK Sensors, Test & Calibration
The Gemco Programmable Limit Switches (PLS’s) are used in a variety of applications from packaging and stamping to every day factory automation. In the Heavy Moveable Structure Industry, they can typically be found in Rail and Draw Bridge Control Houses. These devices are typically found in applications where the PLC scan time cannot keep up with the process.
-
Product
Programmable AC and DC Power Source
AFX Series
-
The AFX Series is a family of high power, single, split and three phase, AC, DC and AC+DC output capable Power Sources. Available models range from 6 kVA to 90 kVA with available configurations to 150kVA. Using a modern user interface for ease of use, the AFX Series is cost effective and fully programmable for both basic frequency conversion and advanced AC power line or DC power disturbance test applications.
-
Product
PXI Resistor Module 4-Channel 1R to 63.7R
40-293-011
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Programmable Delay Line Instrument
XT-200
-
Built using the same technology that made Colby a trusted name, today the XT-200 stands as our flagship product. The XT-200 utilizes not one but two of Colby's patented trombone to offer precise programmable delay or phase shift for dual-channel requirements.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 2Ω to 26.7kΩ
40-251-032
-
The 40-251-032 is a programmable resistor module with 4 channels which can be set between 2Ω and 26.7kΩ with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
VVDI2 Programmer
-
For programming BMW, VAG, PSA or Porsche. The great advantage of the device is the frequency of updates and the lack of a subscription.
-
Product
Programmable Power Supplies
Genesys™
-
The Genesys™ series sets the standard for flexible, reliable, AC-DC power systems in OEM, Industrial and Laboratory applications with the highest power density in 1U, 2U or 3U sizes at a competitive price.
-
Product
Programmable Gain Amplifiers
-
Analog Devices programmable gain amplifiers (PGAs) provide excellent gain accuracy, channel-to-channel matching specifications, and low 1 ppm/°C drift. Set your gain with a simple serial or parallel interface from 1 V/V to over 4000 V/V.
-
Product
Voltage Control Attenuator
-
Voltage variable attenuator offering infinite attenuation precision and broadband performance
-
Product
PXI Amplifier And Attenuator Modules
-
Pickering's PXI Amplifier and Attenuator Modules include our accurate DC to 3GHz programmable attenuator has a 1dB step resolution, allowing it to adjust signal amplitudes for optimum measurement by other devices. The other programmable attenuator available has a bandwidth between 10MHz and 6GHz available in triple or hex formats.
-
Product
Programmable LCR Meter
DU-6211
-
Delta United Instrument Co., Ltd.
Wide Measuring Range & High accuracy 0.1%Zeroing Offset FunctionProvided HI/LOW limit and BIN Sorting comparator function, to meet your needed.100 sets of memory, can be saved test parameter and comparator setting, easy to use.Cover up free, system firmware upgrade can be update via RS-232, easy to maintenanceEasy Test Condition Setting with Auto Parameter Selection & Auto Ranging Function High speed FADC, max. test speed up to 75 meas./sec, faster your automation equipment240*64 Graphic LCD display, can be read the reading clearly and easier.User friendly programmable interface, easy to useProvided RS-232C and Handler combinatorial interface option, to meet your needed
