TTL
Transistor–transistor logic.
-
Product
PCI-6503, 24-Channel, 5 V, TTL/CMOS, 2.4 mA Digital I/O Device
777690-01
Digital I/O Module
24-Channel, 5 V, TTL/CMOS, 2.4 mA Digital I/O Device - The PCI-6503 uses a 24-bit programmable peripheral interface (PPI). Each interface is Plug and Play compatible and does not require a separate card manager for configuration. The PCI-6503 can interface to peripherals or other computers, and it can operate in either a unidirectional or bidirectional mode and handshake with peripheral equipment.
-
Product
TTL/I2C/SPI* Expansion Kit
OP-SB5GL
-
OP-SB5GL is the interface expansion kit that has a port to measure RS-232C(V.24) and a port to measure the TTL / CMOS signal level communications. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communications between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI* on monitoring and simulating.
-
Product
SP5T RF Pin Diode Switches To 12 GHz
-
Pulsar Microwave's 5-way RF switches cover bands from 300 MHz to 12 GHz in both absorptive and reflective configuration. These SP5T switches have a rating of 200 mW maximum input power and a switching time of 100 ns. They are specified with a minimum isolation of 60 dB and most models maintain a VSWR of 1.6:1 or better on all ports. The SP5T switches are driven by TTL logic control circuitry and require both positive and negative 5-volt supplies for operation. A 9-pin D-SUB connector provides the interface for the power and logic voltages.
-
Product
Serial to Digital Interface
-
All of ICS's Serial Digital Interfaces are user configurable and let you transfer data as bits, bytes or as strings of bytes. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard and are HP-IB compatible.
-
Product
PXI-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module
778858-01
Digital I/O Module
96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module—The PXI‑6509 can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is required for outputs. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Low Profile PCI 24 Channel TTL Digital Interface
8018
-
The 8018 Low Profile PCI digital I/O interface provides 24 channels of buffered drive digital I/O emulating 8255 mode zero. The board can be utilized for PC-based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems.
-
Product
PCI-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA, PCI Digital I/O Device
778792-01
Digital I/O Module
The PCI-6509 can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is required for outputs. Using programmable power-up … states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the PCI-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Dynamic Digital I/O (3U), 32 Channels Up To 100 MHz W/256MB On-Board Memory, W/LVDS
GX5282
Digital I/O Module
The GX5280 Series are high performance, cost-effective 3U PXI dynamic digital I/O boards with 32 TTL input or output channels and 32 LVDS input or output channels. The GX5280 Series offers an industry leading 512 MB of on-board memory and supports test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
USB-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA, USB Digital I/O Device
779975-01
Digital I/O Module
The USB-6509 is an industrial, bus-powered USB device that can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is … required for outputs. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the USB-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
6 GHz Programmable Delay Line
PADL6
-
The PADL6 is a programmable delay line instrument designed for adjusting the time delay or phase of radio, microwave or even digital signals with bandwidths from DC to 6 GHz. Delays are controlled via a TTL level bus.
-
Product
32-Ch Isolated Digital I/O Universal PCI Card
PCI-1730U
-
ISA-compatible with PCL-73032-ch TTL DI/O (16-ch digital input,16-ch digital output)High output driving capacityInterrupt handling capability2 x 20-pin connectors for isolated DI/O channels2 x 20-pin connectors for TTL DI/O channelsD-type connector for isolated input and output channelsHigh-voltage isolation on output channels
-
Product
16-bit, 200KHz, 16SE/8DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3116-16
-
The APCI-3116 is a 16-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3116, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
Product
RS232 / RS485 / RS422 / TTL Serial Repeaters & Hubs
-
CommFront offers a range of rugged, industrial-grade RS232 / RS485 / RS422 / TTL repeaters and hubs to meet serial communications' data distance needs by converting unbalanced signals to balanced ones, deploying repeaters to boost signal strength, and implementing hubs for star-configured connections, while still taking full advantage of cost-effective and readily-available copper wire.
-
Product
sbRIO-9403, Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
780539-01
Digital Module
Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The sbRIO‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the sbRIO‑9403 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and other applications.
-
Product
PCI Direct Digital Synthesizers
SYNTH300-TRIG-HS
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
Product
Industrial Controller
Controller
Industrial Controllers are high-performance, fanless controllers that provide connectivity for communication and synchronization to EtherCAT and Ethernet CompactRIO chassis, EtherCAT motion drives, GigE Vision and USB3 Vision cameras, and other automation equipment. Controllers also have onboard isolated, transistor‐transistor logic (TTL), and differential digital I/O. You can use LabVIEW system design software to create, debug, and deploy logic to both the onboard FPGA and the processor. LabVIEW contains over 950 signal processing, analysis, control, and mathematics functions to accelerate development.
-
Product
Chassis - Controls up to 16 8x1 Modules, 32 4x1 Modules or Mixtures or 8x1's, 4x1's, 2x1's and 2x2 Modules in Any Combination or Configuration up for up to 128 Relay Drives
CXM/128-MF
Chassis
These Chassis controls up to 16 8x1 modules, 32 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 128 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional. Chassis is available with sink or source relay drivers from + 5 to + 28 volts, ot TTL drivers for programmable attenuators. Firmware commands for Fade and Handover for WiFi, Cell Phone and WiMax labs. Fully custom systems built with little to no NRE.
-
Product
sbRIO-9401, Non-Enclosed, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module
782400-01
Digital Module
Non-Enclosed, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module - The sbRIO‑9401 is a configurable digital I/O interface for input or output in 4-bit increments. Therefore, the sbRIO‑9401 can create three configurations: 8 digital inputs, 8 digital outputs, or four digital inputs and four digital outputs. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the sbRIO‑9401 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; or other applications. Each channel features transient isolation between the I/O channels and the backplane. Non-enclosed modules are designed for OEM applications.
-
Product
25-Watt AC/DC Power Supply
Model 56GS1
Programmable Power Supply
NAI’s 56GS1 is a 25 Watt AC/DC Power Supply that accepts multiple AC inputs plus a +270 VDC input. This COTS unit provides a single full-power output at a baseplate temperature of +85° C.Standard features include remote error sensing; remote digital (TTL) turn on/off; and protection against transients, overvoltage, overcurrent, and short-circuits. Options such as ESS vibration testing and choice of output voltages are available, and additional options and special units can be ordered.
-
Product
16/32 -CH 16-Bit 250/500 KS/s Multi-Function DAQ Cards with Encoder Input
PCI-9222/9223
Data Acquisition Module
The ADLINK PCI-9222/PCI-9223 is a 16-bit, 16/32-CH, 250/500 KS/s high performance DAQ card with 8 different input ranges. It also features 2-CH 16-bit analog outputs capable of a 1 MS/s update rate, 2-CH encoder inputs, and programmable function I/O. The software-programmable function I/O supports a variety of applications, including TTL digital I/O, high-speed DIO, general-purpose timer/counter, pulse generation, and PWM output. Analog input, analog output, and function I/O at full speed simultaneously, and multiple cards can be synchronized through the SSI (System Synchronization Interface) bus if users need more channels than a single board can provide. Ideal for mixed-signal tests, laboratory research, and factory automation, PCI-9222/PCI-9223 is the best single-board solution on the market providing the best integration capability of multiple tasks with high performance and an affordable price.
-
Product
24-Ch Digital I/O Universal PCI Card
PCI-1737U
-
ISA-Compatible with PCL-72424 TTL digital I/O channelsEmulates mode 0 of 8255 PPIInterrupt handlingOpto-22 compatible 50-pin connectorsOutput status readbackPCI universal card
-
Product
Speed Sensor
SP-TTL
-
Speed measured by counting teeth on a gear and dividing by n (where gear has n teeth).
-
Product
PCI Module
PCI-ECL-II
-
PCI-ECL-II - with Spartan 6 FPGA, 16Mx32 SDRAM, 20 ECL TX , 20 ECL RX, and 12 TTL IO
-
Product
Qseven V2.0 SoM With IMX6 Quad/DualLite 800 MHz (Industrial) SoC, 1GB RAM, 4GB EMMC, GbE LAN, Audio And CAN
Q7M120
-
*Qseven v2.0 (70 x 70 mm)*Ultra low power consumption Cortex™-A9*2 CAN*24-bit TTL signal*LVDS/HDMI 1080P*10/100/1000 Mbps Ethernet*Linux 3.0.35/Android 4.3*Audio
-
Product
Ethernet Parallel Interface
Model 8003
-
* Provides 40 high-power TTL I/O lines.* Fully VXI-11 Compliant plus Raw Socket for easy programming with Visual Basic or C, Agilent VEE and LabVIEW.* Standard board has vertical Ethernet and Digital IO connector on the component side. * Optional Relay Driver board adds 4, 32 or 40 Relay Drivers. • Apply regulated 5 Vdc power through the Digital IO connector.
-
Product
Discrete Module for Multi Protocol 4000 Boards
-
Discrete Module for Multi Protocol 4000 BoardsThe M4KDiscrete is an interface module for the multimode, multiprotocol Excalibur EXC-4000 family of carrier boards. The M4KDiscrete provides a complete solution for developing and testing discrete voltage-level interfaces.The module contains control I/O registers that may be accessed in real time. The module supports 20 discretes. The user can set each discrete:• Either as input or output.• Either to TTL (0 – 5V) or Avionics (0 – 32V) voltage levels and• Either enable or disable external debounceOutput discretes are open collector, capable of handling up to 32V with a maximum current of 100 mA each. There is a 4092 word FIFO, capable of storing 1023 Discrete entries containing the discrete data and Time tags.
-
Product
PXI-6508, 96-Channel, 5 V TTL/CMOS, 2.5 mA PXI Digital I/O Module
777598-01
Digital I/O Module
96-Channel, 5 V TTL/CMOS, 2.5 mA PXI Digital I/O Module—The PXI‑6508 uses four, 24‑bit programmable peripheral interfaces (PPIs) that can each be divided into three, 8‑bit ports. The PXI‑6508 can interface to peripherals or other computers, and it can operate in either a unidirectional or bidirectional mode and handshake with peripheral equipment. The PXI‑6508 is well suited for applications that require onboard pull-up resistors.
-
Product
NI-9401, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module
782401-01
Digital Module
5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module - The NI‑9401 is a configurable digital I/O interface for input or output in 4‑bit increments. Therefore, the NI‑9401 can create three configurations: 8 digital inputs, 8 digital outputs, or four digital inputs and four digital outputs. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9401 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
Product
Pulse Generation Measurement Board
MS 1806
-
*TTL Pulse measurement channels (Timers / Counters) 18 Channels*TTL Pulse Generation - 12 Channels*The Pulse Generation Frequency from 10Hz to 40MHz*The no. of pulses controlled from 1 to 255 pulses*All Channels are compatible with 5V TTL / CMOS*All the pulse input and the output signals driven through Pin Driver*Standard ISA Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
SMARC V1.0 SoM Evaluation Kit With Quad/DualLite 800 MHz (Industrial) SoC,1GB Memory, 4GB EMMC, Gigabit Ethernet, Audio, CAN, MIPI And PCAM
SCM120-120-EVK
-
*Ultra low power consumption Cortex™-A9*2 CAN 2.0B*24-bit TTL LCD*LVDS/HDMI 1080P*10/100/1000 Mbps Ethernet*Open GL ES2.0*Linux3.0.35/Android 4.3*Audio
