Extender Cards
move out from slot circuit card giving access thereof.
See Also: Extender Boards, Cards, Bus
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 8.19k Ohm - SPST
40-294-124
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Pecision Resistor Card, 6-Channel, 3.5Ω To 102kΩ
50-298-040
Programmable Resistor Module
The 50-298-040 is a high density programmable resistor card with 6 channels which can be set between 3.5Ω and 102kΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Express Digital I/O Card With Counters And IRQ
PCIe-DIO-24HC
-
This product is a x1 lane PCIe DIO board with basic DIO, Counter/Timers and interrupt generation capabilities. The card uses an 8255 compatible chip, providing 24 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs. Port C is further broken into two 4-bit nybbles via software, configured as either inputs or outputs.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 510 Ohm - SPST
40-294-114
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
32-CH Isolated DI & 32-CH Isolated DO PCIe Card with High Input Range
PCIe-7432
Analog Input Module
ADLINK PCIe-7432 is a 32CH Isolated DI & 32CH Isolated DO PCIe Card, featuring robust 2,500V isolation protection, suitable for most industrial applications. Input range up to 24V makes it easy to acquire status of external devices (PCIe-7432HIR output range is from 5 to 35V), making it suitable for relay driving and industrial automation applications. Also provided are two easily configurable interrupt sources on digital input channels.
-
Product
32-CH DI & 32-CH DO 12 MB/s High-Speed Card
PCIe-7200
Digital I/O
- x1 lane PCI Express interface- 32-CH TTL digital inputs and 32-CH TTL digital outputs- Up to 12 MB/s transfer rate- Onboard programmable timer pacer clock- Support handshaking digital I/O transfer mode- Bus-mastering DMA for both digital inputs and outputs- 5 V power available on connectors- Compact, half-size PCB
-
Product
Dynamic Digital I/O With Per Channel Timing, Programmable Logic Levels And PMU PXI Card
GX5296
Digital I/O
The GX5296 offers advanced dynamic digital I/O performance and capabilities in a single slot, 3U PXI format. The 32-channel, GX5296 features timing per pin, multiple time sets, data formatting, and an advanced sequencer – providing users with the capability to emulate and test complex digital busses for system, board or device test applications. Offering sub-nanosecond edge placement resolution per pin and a PMU per pin, the GX5296 has the ability to perform both DC and AC parametric testing. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
Product
cRIO-9068, 667 MHz Dual-Core CPU, 512 MB DRAM, 1 GB Storage, Zynq-7020 FPGA, Extended Temperature, 8-Slot CompactRIO Controller
782663-01
Controller
667 MHz Dual-Core CPU, 512 MB DRAM, 1 GB Storage, Zynq-7020 FPGA, Extended Temperature, 8-Slot CompactRIO Controller - The cRIO-9068 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. The cRIO-9068 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, one USB host, and three RS-232 serial. Additionally, the cRIO-9068 supports an extended operating temperature range. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
PCI Precision Resistor Card 6-Channel, 2.5Ω To 395kΩ
50-297-042
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
VME Extender
VME64J1
-
VECTOR Electronics and Technology, Inc.
Excellent performance with a multi layer design
-
Product
Arbitrary Waveform Generator PCI Card
GC1300
Waveform Generator
The GC1300 is a single-channel PCI-based Arbitrary Waveform Generator. It is a high performance waveform generator that combines many powerful functions in one small package. Supplied free with the instrument is Arbconnection software, which is used for controlling the GC1300 and for generating, editing and downloading waveforms from a remote computer.
-
Product
BNC Box-D37M To 16 SE BNC Outputs For 12-Bit PCMCIA DAQ Cards
CB516S
-
*D37M input connector*16 Single Ended BNC output channels*Connects from Ines or Elan 12-bit PCMCIA DAQ cards via CBL-T30-32-D37F cable*Only for Ines or Elan 12-bit PCMCIA DAQ cards
-
Product
PCI Express Digital I/O Cards With Counters And COS Detection
PCIe-DIO-24DCS, PCIe-DIO-24DC, PCIe-DIO-24DS, and PCIe-DIO-24D,
-
This product is a x1 lane PCIe DIO board available in four models ranging from basic DIO to advanced COS detection and Counter/Timer capabilities. The card emulates an 8255 compatible chip, providing 24 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs. Port C can be further broken into two 4-bit nybbles via software and configured as either inputs or outputs.
-
-
Product
High Current Relay PXI Card
GX6115
Relay
The GX6115 is a 15 channel, high current relay board that plugs directly into any 3U PXI slot. The GX6115 also provides three transistor-driven channels for external relays. These outputs may be used to drive external loads, such as heavy duty relays, lamps or other devices.
-
Product
64-CH 16-Bit 250kS/s Multi-Function DAQ Card
cPCI-9116
Data Acquisition Module
- PICMG 2.0 Rev 2.1- 16-bit A/D and sampling rate up to 250kS/s- 64-CH single-ended or 32-CH differential input- On-board 1k-sample A/D FIFO
-
Product
Rack Extender Kit, G12, 1.5" Deep
310113406
Rack Exntender
The Rack Mount Extender Block Kit is used for mounting to racks with recessed mounting rails recessed more than 1.” It is made of aluminum with a black anodized finish. NOTE: Used only with slide mounted G12 Receivers.
-
Product
cRIO-9058, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 8-Slot CompactRIO Controller
787880-01
Controller
1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 8-Slot CompactRIO Controller - The cRIO-9058 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and eight slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with LabVIEW. The controller provides precise, synchronized timing and deterministic communications over the network using TSN, ideal for distributed measurements and control. This controller offers two Gigabit Ethernet ports, one USB 3.1 host port, one USB 2.0 device port, a trigger line, and a μSD card slot for storing data locally. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
PCMCIA Card
DAS-429PCMCIA/RT10
-
Both cards contain 68 Kbytes of true dual-port RAM, for data blocks, control registers and Look-up table, mapped within the Common Memory space. The card also contains a FLASH-based Card Information Structure (CIS) within the Attribute Memory space.The cards comply with the Personal Computer Memory Card International Association (PCMCIA Release 2.1) standard, including Plug and Play. The card's small size and suitability for PCMCIA compatible notebook computers with Type II and Type III slots make it a complete solution for developing and testing ARINC-429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The cards are supplied with C drivers, including source code, Mystic Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
Product
Message Based Intelligent Interface Card
IIB-3910-VXI
-
The IIB-3910-VXI is message based intelligent interface card for dual redundant 3910 and 3838 applications. It gives full 3910 and 3838 test, simulation and bus analysis capability on the VXI bus, providing 3910, 3838 1553A, and 1553B variants in a single card. Each channel supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with passive Bus Monitor, and an independent Chronological Bus Monitor (CBM). Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides dual redundant prEN3715 compatible 3910 interface, with variable amplitude dual redundant 3838 interfaces. External trigger-in and trigger-out are provided, with both Primary and secondary bus coupling for direct and stub bus, with access to internal 1553 bus, on the front panel.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 510 Ohm With SPDT
50-293-114
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
8-CH 16-Bit PCI Express Analog Output Card
PCIe-6208
Analog Output Module
ADLINK PCIe-6208 series are 8-CH, 16-bit, PCI Express analog output cards which provide high resolution, high-density analog output functionalities and are suitable for ATE, signal generation, industrial process control, servo control and other industrial control applications.
-
Product
VPX Extender 6U - P0 Utility, P1 To P6 Diff, Viper
1940000526-0000
-
VPX Extender 6U - P0 utility, P1 to P6 differential, with VIPER connectors.
-
Product
TTENetwork Interface Cards
-
The TTENetwork Interface Cards are pluggable mezzanine cards for network communication combining regular Ethernet with the safety-critical time-triggered technology from TTTech. They enable real-time Gbit/s Ethernet communication between a computer and TTESwitches for redundant channels in a safety-critical way.
-
Product
USB Extender via CAT5 to 200 Feet
USB-C5-200
-
The USB-C5-200 extends up to four self-powered or bus-powered USB devices to 200 feet. The USB extenders consist of two units, the local unit and the remote unit, which are interconnected with CAT5/5e/6/7 cable.
-
Product
PXI Optical Extenders for Instrumentation
-
The Keysight Optical Extenders for Instrumentation offers capability that is modular, scalable, and upgradable to meet the challenging demands of applications requiring long distance RF paths. Configure a single link, extend the port of your PNA, or design a system that includes remote operation of the measurements while achieving an RF signal path over distances that have been impossible until now.
-
Product
CPCI 48 Input I/O Card with Zilog Z8536 I/O Controller
CPCI-48IN
Controller
The input board consists of three Zilog Z8536 controllers for DC input control. An FPGA provides the timing and control. Each input has its own optical isolation, and supports a hardware adjustable resistor/opto-diode combination for various input voltage ranges. An AMCC PCI controller provides the interface to the host computer. All I/O is accessible from the front panel.
-
Product
8-CH Relay Outputs & 8-CH Isolated DI PCI Cards
PCI-7250/7251
Relay
ADLINK's PCI-7250/7251 provide 4-CH SPDT (Form C) & 4-CH SPST (Form A) relay outputs and 8-CH isolated digital inputs. The status of each relay output is represented by an onboard LED. When the relay is in SET condition, its corresponding LED will turn ON, and on the contrary, it is OFF. All digital input channels are nonpolarity, optically isolated, and may be set to use RC filter or not. The devices are suitable for collecting digital inputs in noisy environments. The PCI-7251 is an 8-CH relay outputs and 8-CH isolated DI extension card of the PCI-7250. All the I/O functions of PCI-7251 are the same as those of the PCI-7250. The PCI-7251 has to be connected with PCI-7250 and the bus interface is controlled by the PCI-7250. Up to three PCI-7251 cards can be connected to one PCI-7250, therefore, expanding the PCI-7250's DIO from 8 DIO to maximum 32 DIO.
-
Product
cRIO-9031, 1.33 GHz Dual-Core CPU, 1 GB DRAM, 4 GB Storage, Kintex-7 70T FPGA, Extended Temperature, 4-Slot CompactRIO Controller
783451-01
Embedded Controller
1.33 GHz Dual-Core CPU, 1 GB DRAM, 4 GB Storage, Kintex-7 70T FPGA, Extended Temperature, 4-Slot CompactRIO Controller - The cRIO-9031 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. You also can use the Mini DisplayPort to add a local human machine interface (HMI) for application development. The cRIO-9031 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, two USB host, one USB device, and two RS-232 serial. Additionally, the cRIO-9031 supports an extended temperate range. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
Probe Card
T90™ Series
-
The 90 mm tile was designed for mounting on a standard 4.5″ probe card holder for multi-site wafer level reliability testing. The 1.6 mm (0.062″) thick rails allow the chassis to slip into planarity adjustable probe card holders for most analytical probe stations.
