-
Product
Digital Panel Meter
ST-312V (ST-312mV)
-
Standard Electric Works Co., Ltd
● 3 1/2 digit liquid crystal display.● 200mV and 2V full scale input sensitivity.● Single Battery operated 9V supply or ±5V DC power supply (Dual supply).● Built-in low battery indication and automatic polarity indication.● Decimal point selectable.● Low power dissipation Typically less than 20mV.● High input impedance (> 1M ohm).● Guaranteed zero reading for 0 volts input on all scales.● True differential input or single-ended input.● Self mountable with optional mounting bezel.● Low cost high performance.● EN 50081-1 EN 50082-1 EN 55022 EN 61000-4-2 IEC 801-3
-
Product
Earth/Ground Resistance Tester
DE-5030
-
Earth resistance range0~12 / 0~120 / 0~1200 Normal operation conditionsBattery voltagein range of "BATT.GOOD" Earth voltage measurementmax. AC 30V Output current3mA Response timewithin 1 sec. Insulation resistancemin. 100M / DC1000V between input terminals and case Withstand voltageAC3700V (50 / 60Hz) for 1 min. between input terminals and case Battery Check Battery1.5V x 4 Safety standardIEC 61010-1 CAT.III 300V IEC 61557, IEC61010-031
-
Product
IEC60884 Fig38 Thermal Compression Test Device For Plug Testing
IEC60884 fig38
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig38 thermal compression test device for plug testingUsed to evaluate the pressure resistance of electrical accessories and wall mounted mounting boxes under heatStandard: GB2099.1-2008 Articles 24.19 and 25.4 and Figure 38, IEC60884-1 Figure 38, etc.
-
Product
20KV 30KV Electrostatic Discharge Generator ESD
ESD-202AX
-
Shenzhen Chuangxin Instruments Co., Ltd.
ESD simulator is in full compliance with IEC 61000-4-2, EN61000-4-2, ISO10605, GB/T17626.2, GB/T17215.301 and GB/T17215.322. The ESD generator is designed for the assessment of electrical and electronic equipment to withstand ESD performan
-
Product
Conformance Calibration Standard Test Card for ISO/IEC Data Matrix and GS1 DataMatrix Symbol Verifiers
AI-CCS-DM-G Rev A
-
This precision 2D barcode Conformance Calibration Standard Test Card is the first 2D test card to provide ALL 12 of the Primary Reference Symbols specified by ISO 15426-2 for barcode verifiers. They are sized from 0.5mm to 0.2mm so that all the symbol sizes specified in Annex A.3.1 can be tested. Symbols 1-4 are GS1 DataMatrix symbols, while symbols 5-12 are ISO/IEC Data Matrix symbols consistent with the ISO/IEC 16022 standard. The card also includes four calibrated reflectance patches.
-
Product
EMC Test Systems
IEC61000
-
N4L are the only IEC61000 EMC test system manufacturer in the world* with an on site UKAS ISO17025 calibration laboratory offering accreditation to IEC61000-3-2, IEC61000-3-3, IEC61000-4-7 and IEC61000-4-15. Calibration and trace-ability are a vital aspect of any EMC test solution and the coverage provided through N4L’s UKAS Laboratory is comprehensive. N4L’s IEC61000-4-15 calibration procedure is particularly noteworthy as it covers the entire test protocol detailed in Annex C of IEC61000-4-15. It is commonplace for specific parameters within IEC61000-4-15 (d parameters are frequently omitted from calibration procedures) to remain untested during typical flicker calibration due to the difficulty in providing trace-ability for such measurements. All tests within the test protocol of Annex C are included within the scope of accreditation and calibration procedures at N4L.
