Environmental Simulation
-
Product
Basic Rate and Primary Rate Simulator
emutel Pro
-
Emutel Pro has the same features as the Emutel but has 2 BRI and 2 PRI which will allow you to test both basic rate or primary rate equipment or basic to primary links to be set up. Emutel Pro has optional network support and protocol analysis.
-
Product
Environmental Test Probe, Temperature
72-8366
-
Simple thermocouple junction at the end of a 1m wire provides effective low cost ambient temperature measurement. It is suitable for measuring air temperature and may be placed in direct contact with hard surfaces. Type K thermocouple temperature probes are commonly used with all types of industrial temperature controls and measurement equipment, and are compatible with Tenma handheld thermometers and digital multimeters that include temperature function. All are terminated with standard Type K plugs.
-
Product
1 Or 2 Stream MIL-STD-1553 PMC Test And Simulation Modules With Prog. Coupling,onboard Bus Network And Variable Output Amplitude
AMCX1553-xT
-
MIL-STD-1553 Test and Simulation modules for PMC with 1 or 2 Dual Redundant streams plus 8 Discrete I/O’s (on Rear-I/O).
-
Product
Compact Environmental Chambers
MicroClimate 3
-
The MicroClimate 3 is a compact environmental chamber designed to simulate a full range of temperature and/or humidity conditions. The small footprint of the MicroClimate 3 combined with temperature and humidity capabilities make this chamber the number one choice for testing small components and products. Whether you need to perform temperature cycling tests or expose your product to steady state temperature environments, these chambers will maintain precise and accurate temperature/humidity control throughout your test.
-
Product
Terminal Equipment Simulator
AI-5620
-
The AI-5620 simulates a single port two wire analog TE (Terminal Equipment) or CPE (Customer Premise Equipment) device. It is designed to measure and analyze signals generated by a CO (central office) line card, VoIP terminal adapter FXS port, or any device utilizing a SLIC (subscriber line interface circuit).
-
Product
Solar simulation systems
-
Whatever your application, from an environmental chamber for small components to an extensive array for a complete automobile or aircraft test, EYE / Iwasaki has the experience to provide a solar lighting system customized for your requirements.
-
Product
DGS-65 Test Panel with FV Simulator / Bed of Nails
TA-650
-
The TA-650 is a new test fixture that will give any instrument shop the ability to conduct more detailed testing of the Collins DGS-65 directional gyro then was previously available.
-
Product
Dynamic Data Simulator
LS-70-S
-
The Lumistar LS-70-S PCI Dynamic Data Simulator allows complex data streams to be generated for evaluation of bit synchronizers and PCM decommutator performance. It can also be used for uplink command generation to vehicles in flight, checkout of complete telemetry links, and playback of archived hard drive data in any format with the appropriate dll. The PCI board is only 7 inches long and contains the dynamic simulator and IRIG Time Code Generator.
-
Product
Environmental Meter
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
The meter can test Sound Level and Temperature.
-
Product
Walk-In/Drive-In Humidity Environmental Chamber
-
Burnsco Environmental Test Chambers
These custom designed chambers are used for testing large products, vehicles, or batch testing. They offer temperature and humidity simulation capabilities for climatic testing and temperature/humidity cycling whenever there is a need to simulate wide temperature and humidity extremes. They can be made almost any length, width or height.
-
Product
LOCAL LOOP SIMULATOR FOR TR-114INCLUDING BRIDGED TAP
458-LM-A1-30-TR114
-
The Model 458-LM-A1-30-TR114 Local Loop Simulator for TR-114 is the ideal solution for simulating test loops as defined in TR-114 and includes a Bridged Tap. In addition, it is also suitable for ADSL, ADSL2, ADSL2+, and VDSL2 chip/modem/DSLAM testing of straight loops out to 24,000
-
Product
Force On-Force Reactive Tactical Readiness IADS Simulation
FORTRIS™
-
FORTRIS™ is a scenario engine that provides a real-time complex battle simulation between hostile and friendly forces. The Synthetic Environment within FORTRIS contains a true multi-layered Integrated Air Defense System (IADS) simulation that can act and react both as an overall system, as well as individual contributors, making it the ideal cognitive training tool within the Live Virtual Constructive (LVC) world.
-
Product
MIL-STD-1553 Simulator & Analyzer Applications Software
F-SIM-1553
-
Avionics Interface Technologies
Software GUI Application for Operating AIT MIL-STD-1553 Interfaces - Bus Monitor Captures & Recordings - Simulate Bus Controller and Remote Terminals (up to 31) - Operate Multiple Bus Channels (and MIL-STD-1553 Modules) Simultaneously - Replay Previously Captured Bus Data - Full Error Injection & Detection - Engineering Unit Displays & Software Widgets - MIL-STD-1553 A/B Mode Code operations - Also Supports ARINC 429, ARINC 664, Ethernet, & Data Load operations
-
Product
MIMIC® MQTT Simulator
-
MIMIC MQTT Simulator is a scalable, customizable, programmable, predictable, dynamic simulation platform designed to enable rapid development / testing / deployment / tuning / training / demonstration of large-scale Internet of Things applications.
-
Product
Simulation & Analysis Solution for Automotive Audio Networks
A2B Analyzer System
-
The A2B Analyzer System is designed specifically for development teams servicing automotive OEMs, Tier 1s, and audio connectivity equipment suppliers. The deterministic nature of the A2B technology makes it particularly well-suited for automotive audio devices (active speakers, microphones) and newer applications such as ANC. The A2B Analyzer System consists of a compact hardware device, an accompanying software development kit (SDK), and network configuration and simulation tools.. The hardware device includes a USB 2.0 interface for PC connectivity for audio data and command/control functions. The small form factor device also features a variety of popular audio and connectivity peripherals.
-
Product
Rain Spray Test Environmental Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s rain spray test environmental chamber is also known as rain spray test chamber, it is used to test the water resistance for electronic and electrical products, such as solar lights, garden lights, buried lights, tunnel lights, car lights, fountain lights, the display…etc. It can also provide references for product design and quality control.
-
Product
Regenerative Grid Simulator
Chroma 61800
-
Chroma Systems Solutions, Inc.
Full 4 quadrant, fully regenerative, AC power supply designed for common electrical product testing such as home appliances and industrial electronics that require a programmable input source
-
Product
Environmental Noise Monitoring System
E-Box LIVE
-
This is the ultimate solution to environmental noise monitoring. The LIVE comes equipped with a modem that connects directly to our Castle Cloud software allowing you to monitor your results from the comfort of your own desk. Combine this with the ability to customise your power supplies and you will see why this is the ultimate solution for environmental noise monitoring.
-
Product
Model Based Design and Simulation
-
Requirements validation through simulation and autogeneration of embedded systems
-
Product
16-Channel VME Analog Output/Thermocouple Simulator Module
V470
-
The V470 is a 6U VME module that provides sixteen independent, isolated analog outputs that may be user-programmed to operate as voltage outputs or thermocouple simulators. Users may write temperature or voltage values at VMEbus speed, and the microprocessor will transparently do all necessary calculations and update the channel electronics.
-
Product
PXI 16 Channel Switch Simulation Module
40-480-121
-
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
Product
USB 2.0 SmartCable™ For ARINC429Test And Simulation
ASC429-x
-
USB 2.0 SmartCable™ for ARINC429 Test and Simulation with 6 channels (2Tx/4Rx) and 12 channels (4Tx/8Rx).
-
Product
Voltage Variation Simulator
KES7400A
-
The KES7400A Series comes in a single cabinet that consists of a Signal Generator module (including an arbitrary pulse generator), which combines our power supply technology and EMC technology, and a high-speed bipolar power supply module. Many automotive electronic devices have long wire harnesses and inductive load characteristics, as do motors, or capacitive load characteristics with a large-capacity capacitor connected between the input and ground. In the case of these devices, general DC power supplies exceed the linear operation range, potentially making it impossible to obtain the desired waveform output.
-
Product
PCI Strain Gauge Simulator Card, 2-Channel, 3k
50-265-102
-
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Production Caller ID Signal Simulator
AI-80
-
The AI-80 is a fully programmable stand alone Caller ID signal generator designed for production environments. It is capable of generating signals for all FSK and DTMF based Caller ID standards. Includes general telephone signal analysis features and a highly flexible programming language for sophisticated and complex production testing sequences.
-
Product
ARINC-708/453 2-Channel Test & Simulation Module for the Weather Radar Display Databus
M8K708
-
The M8K708 module is an ARINC-708 / 453 2-channel test and simulation module for the Weather Radar Display Databus. The M8K708 supports two ARINC-708 / 453 channels, each selectable as transmit or receive. Each channel implements an 64K×16 FIFO and supports polling and/or interrupt driven operation.The M8K708 comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. In addition, Excalibur produces adapter cables that convert the carrier board I/O Molex™ connector to two twinax CJ70-49 connectors. The cable may be purchased at an additional cost.
-
Product
Flux Valve Simulator
FV Sim
-
This flux valve simulator is designed around the synchro format and is employed in our TA-14 DG panel. This simulator is also available now in a portable enclosure for testing the Sperry or Jet Directional gyros.
-
Product
Environmental Test Chamber
-
The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip.The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1 and humidity is 0.1%R.HThe temperature sensor is platinum PT100 Ohms/MV resistor
-
Product
Multiphysics Simulator
-
The COMSOL Multiphysics simulation environment facilitatesall steps in the modeling process defining your geometry, specifying your physics, meshing, solving and then post-processing your results. Model set up is quick, thanks to a number of predefined modeling interfaces for applications ranging from fluid flow and heat transfer to structural mechanics and electromagnetic analyses.
-
Product
Precision RTD Simulator
RTD Series
-
The RTD Series Precision RTD (Resistance Temperature Detector) Simulator provides a very broad-range of absolute resistance values that replace RTD's and thermocouples. Thermocouples present a resistance that depends on the temperature. The RTD simulator effectively replaces an RTD to test, analyze, and calibrate RTD measuring systems. The RTD Series simulator is a precision resistance source with excellent characteristics of accuracy, stability, temperature coefcient, and power coefcient. All these features serve to make it a laboratory resistance standard, exceeded in performance only by stand-alone standard resistors. The special design of the RTD Series provides absolute accuracy, and requires no zero resistance subtraction from any setting Special design of the RTD virtually eliminate zero resistance and switch contact variations, providing the specified absolute accuracy over the entire range.
