Sensor Testers
-
product
Non-Contact Voltage Tester
NT-303
Contact - free electrical socket indication at AC voltages between 90V-240V. Clear alarm system: flashing LED with beeper alarm.. Quick and accurate detection of circuit breaks.. Includes a small screwdriver for easy batteries replacement.. Pocket pen-type design, easy to carry and store.
-
product
Automated Torque Tester
NJY-H5
NJY-H5 Automated Torque Tester is professionally suitable for testing the torque value of the caps of packaging products such as bottles, beverage bottles, mineral water bottles, and milk bottles. It is an ideal configuration instrument for offline or online testing of production units in the packaging industry.
-
product
Compressed Air RH+T+Tdp Sensor
T0211P-4
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
Multifunctional Electrical Installation Testers
Eurotest XA
The fifth generation of Metrel's multifunction electrical installation testers brought know-how in the testing procedures to reality. Because of the need to be efficient, faster and competitive but still responsible and concentrated on safety, all the technical content and innovations under AUTO SEQUENCE, rotate around taking care about testing procedures itself.
-
product
Digital Temperature Sensor
STS35
Sensirion, a leading provider of environmental and flow sensor solutions, presents the STS35 temperature sensor – the most accurate sensor of the versatile STS3x series. The high-accuracy temperature sensor has been designed to fulfill the needs of demanding markets such as the medical and automotive sectors. Typical applications include body temperature measurement and temperature control. Typical accuracy of up to 0.1°C.
-
product
Iveco Oxygen Sensor
KS60113 - Iveco
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Prodution Testers
Effitest E50
Effitest e50 is a flexible and cost efficient solution with easy programming, debugging of test programs and life-cycle support.
-
product
Radio Frequency Cable Tester
RFCT
Textron Systems’ Radio Frequency Cable Tester (RFCT) allows for on-site testing and maintenance for radio frequency (RF) transmission paths within a platform. Using preconfigured databases of sweep parameters and pass/fail criteria, the RFCT quickly determines the status of installed RF cables. The RFCT checks each cable’s performance characteristics to include voltage standing wave ratio (VSWR), insertion loss (IL), phase and phase matching. If a cable fails a test, the RFCT automatically determines the distance-to-fault (DTF). With its intuitive touchscreen-based user interface and lightweight, ruggedized packaging, the RFCT is the gold standard for operational-level RF cable testing.
-
product
Power Meter Tester
MT-3551T
Kongter Test & Measurement Co., Limited
It is multi-functional in field testing for power meters and metering units of all wirings. Testing functions include: metering unit and power meter. With these function, it is widely used in power utility, substation, telecom machine room and the alike for power consumption examination, circuit breakage inspection, power abnormality analyzing, asset management and industrial production management.
-
product
Electronic AC/DC Voltage Tester
ET60
The ET60 voltage tester requires no batteries as it measures AC/DC voltage up to 600V in electrical circuits, outlets, light fixtures and anywhere else AC/DC voltage testing is required.
-
product
Light Section Sensors
Leuze electronic GmbH + Co. KG
Switching light section sensors are designed to perform scanning, two-dimensional object detection along a laser line. They are especially well suited for completeness monitoring or product monitoring in the case of multiple track transport. The short measurement time and the detection range from 200 to 800 mm enable an inspection of the content at a high throughput rate even with deep containers. The internal data processing offers programming and differentiation of 16 different object types, thereby conserving control capacity. Complex detection tasks can be solved with one sensor. The compact housing ensures high flexibility during installation and saves installation space.
-
product
IR Linear and 2D Sensor Array Modules
Excelitas offers Linear and 2D IR Imager Arrays based upon our Thermopile Technology. All Arrays are provided as plug-and-play Modules featuring a sensing chip, robust metal housing with focusing lens, a PCB with microprocessor for calibration and bus interface and a quick connector for streamlined plug-and-play integration. We offer 8-pixel, 16-pixel and 32-pixel Linear IR Imager Array Modules for field-proven effectiveness in scanning presence detection, non-contact temperature measurement, smart-home products, and office electronics. Custom solutions also available upon request.
-
product
4-Wire Universal Cable/Harness Tester
LX-760+
Shenzhen Lian Xin Technology Co., Ltd.
The system provides English/Chinese free switch operation interface·4-Wire Measurement
-
product
45 Degree Flammability Tester
TF310
TESTEX Testing Equipment Systems Ltd.
45 Degree Flammability Tester, is to determine the fabric flammability (fabric burning test) under controlled conditions, complies with standards like 16 CFR Part 1610, ASTM D1230, ASTM F2100.
-
product
Large Range Resistivity Tester
HS-SFRT
HS-SFRT silicon filament resistivity tester is an advanced silicon cylinder resistivity tester, which can measure silicon filament, silicon phosphorus ingot, silicon boron ingot, seed crystal and so on. As it eliminates Peltier effect, Seebeck effect, minority carrier inject effect and so on, So it improve the accuracy greatly. The testing resistivity ranges from 0.0005Ω·cm to 50000Ω·cm. It is accurate, stable and convenient and a good friend to Siemens polysilicon material producer, SH4 polysilicon material producer, UMG polysilicon material producer and so on.
-
product
Electrical Test & Measurement Tester
Evolusys Technologies Sdn. Bhd.
• Polarity • Forward & Reverse Voltage• Forward & Reverse Current• Snapback/Thyristor• Open/Short measurement• Contact check (optional-apply for Keithley C series only)
-
product
High-Temperature Zeus PEEK FBG Cable Sensor
Technica Optical Components, LLC
The T150 is a ruggedized high temperature non-metallic cable sensor designed for monitoring distributed temperatures and strains in environments to 260 Degrees Celsius with submillisecond response time. High temperature resistant non-metallic sensor. Ideally suited for applications where there is concern that the high temperature or chemical composition of the surrounding environment will cause damage to the sensors.
-
product
Force Logger Sensor
NUL-211
This sensor can measure the mass to weightrelationship and study how different pulleysystems affect the effort needed to lift weights.It can also be used to measure push/pull forcesand impacts. There is a hook at the bottom of the force sensor that can be connected to various pulling loads.
-
product
High Voltage Breakdown Tester
Model HV-55
Laxtronics Instruments & Controls Pvt. Ltd
5 Kilo Volt AC, 5 Kilo Volt DC, 30 Milli Ampere, Timer 0 To 100 Seconds, HV Prods, Start-Stop-Trip-Reset Using Single Switch On The Test Prods. Start Function Apply Test Voltage From 0 To Set Voltage Gradually.
-
product
Hardness Testers
The QATM hardness tester portfolio covers all standard test methods, such as Vickers, Brinell, Knoop & Rockwell, as well as a wide test load range. The entire hardness tester range is characterized by technological innovation, precise measuring instruments and maximum comfort due to automation and advanced interfaces.
-
product
SCSI CABLE TESTER
ST123
Continuity tests alone are not sufficient to qualify SCSI cable assemblies. Proper testing of SCSI cables must include a test for correct connection of twisted pairs and shielding. Continuity tests check only that wires are making connections on both ends of a cable.Twisted pairs in the cable must be matched with the correct SCSI signal pairs - otherwise, it is possible to have a SCSI signal (signal and ground pair) placed on wires that are not in the same physical twisted pair (see diagram at right). This will cause crosstalk with resultant SCSI errors.
-
product
Production PCB Combinational Tester
The PT100Pro combines ARM Functional Test, Analog Test and Boundary Scan in one platform for testing up to 32 PCBs at a time. The PT100 Pro solves the test challenges and cost requirements of testing small, high-volume PCBs used in the home, mobile, entertainment, automotive and embedded markets. PCBs in these markets are cost sensitive yet require high volume, high fault coverage on leading edge technologies such as WiFi, DDR Memory, USB, Bluetooth, Nand Flash, MPEG decoders, Power Management Units, and MMC/Smart Cards interfaces.
-
product
Hipot & Electrical Safety Testers
Vitrek manufactures two different series of hipot and electrical safety testers. These testers have been designed to fit your testing application. Each series offers 6 different models with a wide variety of test functions and capabilities.
-
product
Digital Temperature Sensor
ZET 7021
Digital temperature sensor ZET 7021 is designed for measuring temperature of liquid, solid, gaseous and granular mediums, which are safe for the material of thermocouple casing. Application spheres: heat power energy, chemical and metallurgical industry.
-
product
Aerodynamic Filtration Performance Tester
DRK9007C
Shandong Drick Instruments Co., Ltd.
Used to test the gravimetric efficiency performance of air filters.
-
product
Battery Leak Testers
Battery leak testers are crucial tools in the quality assurance process for battery manufacturing. These testers are designed to detect any leaks in battery cells, ensuring that the batteries are safe and reliable for use. Battery leaks can lead to reduced efficiency, potential damage to devices, or safety hazards. By employing sophisticated techniques, such as pressure decay methods or helium detection, battery leak testers can identify even the smallest imperfections in battery casings. These testers are essential in industries where battery reliability is critical, such as in automotive, consumer electronics, and renewable energy sectors, ensuring that the batteries meet stringent safety and quality standards.
-
product
Pulse Characterization Sensors
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables. Attenuating filter accessories are also available to increase their dynamic range. Different models offer silicon, UV enhanced silicon and InGaAs PIN photodiodes, covering a combined spectral range of 193 nm to 1700 nm. Rise times range from 25 picoseconds to 3 nanoseconds. The fast rise times are achieved by an internal reverse bias voltage circuit. Power is supplied by internal batteries and/or an external power supply depending on the model. Detectors should be connected to a 50Ω impedance in order to maintain their nominal rise times. They can be connected to higher impedance loads, but this will result in a significant increase in the rise time. If higher output voltage is required, it is recommended to connect the detector to a trans-impedance amplifier with an Input impedance of 50Ω
-
product
Cable Testers
E448
The EMO cable testers are designed for use in portable and bench mounted applications, including the assembly and testing of cables.
-
product
Spring Back Tester
HTJ-16
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard: JB/T4279.4-2008Used to measure the spring back characteristic of enameled round wires with nominal conductor diameter of between 0.080mm and 1.600mm;Number of winding turns: 5 turns and a halfStop accurately at zero position of the scale after automatic windingAs soon as the value of spring back angle stop counting, the dial will stop to rotate immediately, so that the value displayed on LED and read on the dial are the same.Sensor is unnecessary to be adjusted for samples of different specificationsCoils loosen slowly during spring back, no action of spring back or jump suddenly.Application of SCM control allows for fast operation and strong anti-interference capacity;





























