Open Short
Pinpoint open circuits.
-
Product
4-in-1 OSLT Calibration Kit, DC to 26.5 GHz, Type-3.5 mm (m) 50 Ohm
CK520A
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
LAN Check With Tone Generator
PH-01
-
The LANCHECK consists of two modular units, a tester and a remote terminator. The modular design enables the tester to be used for local loop-back testing of patch cable or remote testing of pre-installed premise wiring. The LANCHECK makes it easy to recognize opens and shorts within a cable as well as identify reversed and miswired cables. It can verify a cable up to 2,000 feet in length. Furthermore, it comes with shielded connectors, which enables the testing of shielded twisted pair (STP) cables. It also features convenient Auto Scanning and precision Manual Scanning modes.
-
Product
PXI-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
778572-14
-
7-Channel, 40 A PXI Signal Insertion Switch Module—The PXI‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
Product
x1149 Boundary Scan Analyzer
N1125A
-
The x1149 is a tool for engineers to perform structural test such as opens and shorts tests on their PCBAs. It also performs In-System Programming for devices such as FPGAs and CPLDs.
-
Product
PXI Signal Insertion Switch Module
-
PXI Signal Insertion Switch Modules, also known as fault insertion units (FIUs), provide a set of feedthrough channels, which make the switch transparent to the system when closed. You can open or short these channels to one of two fault buses, allowing you to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI Signal Insertion Switch Module can validate the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs). You can also use the FIU models for hardware-in-the-loop (HIL) applications and electronic reliability tests.
-
Product
Time Domain Reflectometers
T3SP Series
-
Teledyne Test Tools T3SP15D stimulates the DUT with true differential signals. The T3SP15D offers fast rise times of 35 ps for spatial impedance resolution (in FR4) of 3 mm, at DUT lengths up to 40 meters and TDR repetition rates up to 10 MHz and uses the same open short load thru (OSLT) calibration standards as vector network analyzers. With their small form factors, light weight, and optional internal batteries, the instruments go anywhere in test labs or in the field at an affordable price.
-
Product
Transformer & Capacitor Testers
-
*Quick and easy check for opens or shorts on transformers before energizing*Provides clear indications of open circuits, short connections and confirmation that the test results are OK*Tests overhead, pad-mount and other distribution transformers*Tests the primary and secondary sides of de‑energized transformers without disconnecting*Helps prevent line workers from installing a fuse on a shorted transformer*Automatic self-test feature*Magnet holds the tester in place while testing
-
Product
Telemetry Transmitter
TT22 Series
-
Systems Engineering & Management Company
The TT22 series of 0.25W telemetry transmitters are designed to transmit data in the frequency bands covering 1710-1850 MHz or 2185-2485 MHz. These transmitters are true FM, modular, all solid state and are protected for operation into any VSWR, without damage, including open or short circuit.
-
Product
PXI-2510, 68-Channel, 2 A PXI Signal Insertion Switch Module
778572-10
-
68-Channel, 2 A PXI Signal Insertion Switch Module—The PXI‑2510 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2510 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
Product
Network Tester
-
ZhangZhou Weihua Electronic co.,ltd
There is nothing worse than running your drops only to learn that you have a fault in one of the cable runs. Get it right the first time, get it right by choosing and using the right LAN Cable Testers. We offer a variety of cable testers, which are a must have to quickly and easily verify the integrity of Ethernet twisted pair cables. Our LAN testers will test twisted pair cables for open pairs, shorted pairs, reversed pairs, crossed pairs and split pairs. Network cable testers vary in complexity and price, but a basic tester consists of a source of electrical current and a measuring device. After that, cable testers vary in complexity and ability to do various testing.
-
Product
3-in-1 OSL Mechanical Calibration Kit, DC To 50 GHz, 2.4 Mm (m)
85564A
-
The 85564A 3-in-1 mechanical calibration standard combines an open, short and load standard in a compact unit. The product is small, easy to handle, and lightweight. All standards in the 85564A are male 2.4 mm.
-
Product
Cable/Harness Tester
IST-380
-
IST Information Scan Technology, Inc.
THE IST MODEL 380 is a portable, stand-alone cable/harness tester for testing any cable up to 128 points. It detects opens, shorts, and miswires within one second by comparing the test result with the golden file or the data learned from a sample good cable. The error messages can be shown on the LCD display or printed out on a printer with the correct wire list needing reworking.
-
Product
4-in-1 OSLT Calibration Kit, DC to 18 GHz, Type-N (f) 50 Ohm
CK519A
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
In-Service Electrical Continuity Test Card
Cisco ONS 15454
-
The Cisco ONS 15454 In-service Electrical Continuity Test Card is a solution for confirming proper DS-1 and DS-3/EC-1 cabling between the Cisco ONS 15454 shelf assembly electrical interface adapter (EIA) panels and the user's patch panels. The solution is designed for shelf installations that are presently carrying traffic and tests for common wiring errors including electrical shorts, opens, wrong connections, and tip/ring reversals.
-
Product
4-in-1 OSLT Calibration Kit, DC to 18 GHz, Type-N (m) 50 Ohm
CK518A
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
Lan Cable Tester
-
Shanghai Beha Electronics Co., Ltd.
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.• The Lan cable tester can verify cable continuity, open,short circuit and miss-wired.• The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.• Auto and manual scan function.• Ground wire test.• Lock status function.• Buzzer sound warning for wire status.• Display: LED indication for wire status.
-
Product
4-in-1 OSLT Mechanical Calibration Kit, DC To 40 GHz, 2.92 Mm (f)
85561A
-
Combines an open, short, load, and through standard in a compact unit that is easy to handle and lightweight.
-
Product
Cable Fault Locators
-
Cable Fault Locator is a device used for short circuit faults, cable cuts, resistive faults, intermittent faults, and sheath faults. Fiberinthebox supply cable fault locator for power cable, optical fiberal cable, etc. Fault Location in Power Cable is designed to locate cable faults, pinpointing the fault location, route tracing, cable identification, voltage withstand test and cable information management. It can locate all kinds of cable faults for all voltage level cables, including open circuit, short circuit, low insulation, high insulation and flashover faults, etc. Most power cables were buried underground, invisible, and out of reach, with modern new power cable fault locater, it can find the fault point quickly, solve problems immediately and restore power supply.
-
Product
Cable Fault Locator
FaultCaster
-
Low Cost Full specification Professional Digital TDR Measures Distances to Open or Short Circuit Faults Extended Measuring Range to 2000m (6000ft) on all cable types Fast-Edge Step TDR technology for improved range & Resolution
-
Product
Cal Kit, 4-in-1 OSLT, DC To 26.5 GHz, 3.5 Mm(f)
85521A
-
Easily calibrate non-insertable devices with this module combining an open, short, load, and through in a compact unit
-
Product
PXI 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
40-205-008
-
The 40-205-008 (PXI) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
Product
Transformer/Capacitor Test Sets
-
*Quick and easy check for opens or shorts on transformers or capacitors before energizing*Provides clear indications of open circuits, short connections and confirmation that the test results are OK*Tests overhead, pad-mount and other distribution transformers as well as capacitors and capacitor banks*Tests the primary and secondary sides of de-energized transformers and capacitors without disconnecting*Helps prevent line workers from installing a fuse on a shorted transformer or capacitor*Automatic self-test featureMagnet holds the tester in place while testing
-
Product
PC-NET Cable Tester
PR-09
-
The PC-NET Cable Tester is a portable, stand-alone unit that provides an affordable way to quickly test PC, Network, Telco, Coax, USB and IEEE1394 cables for continuity and wiring configuration for any combination. Open, shorts, miswires and cross-connected wires are detected immediately. The interchangeable connectors boards offers flexibility and convenience easy to read LED instantly indicates good or faulty. The tester is suitable for use by computer dealers and computer hardware outlets.
-
Product
Rack Mount Audio/Lighting/Network Cable Tester
AudioJog Rack 8
-
There are 2 rows of 9 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found.
-
Product
4-in-1 OSLT Mechanical Calibration Kit, DC To 18 GHz, Type-N (m) 50 Ohm
85518A
-
Easily calibrate non-insertable devices with this module combining an open, short, load, and through in a compact unit
-
Product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 8 Channel
50-201-008
-
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
Product
Fault Injection Module
WF 3154 C-Series
-
The WF 3154 from WireFlow is a 4-channel Fault Injection Module for Compact RIO. Each channel provide three solid state relays that can be used to create electrical fault conditions like: Open circuit, Short circuit to battery, Short circuit to ground.
-
Product
LAN Cable Tester
-
Is a hand-held test instrument that lets you verify and troubleshoot the LAN cable of twisted pair. It displays graph wire-map, opens, shorts, miswires, split pairs and the remote ID number all on one screen.
-
Product
Wire/Cable Harness Tester
PANTHER 4HT
-
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
Product
Length Network Cable Tester
SC-8108
-
1. Measure network cable length and determine the distance of breakage point.2. Check wiring error in 5E, 6E, coaxial cable, such as open circuit,short circuit, jumper wire, reverse connection .3. Portable unit with long battery life (wait-case 50 hours).4. Automatically time-delay shut off.5. Self-checking and automatically compensate any change in battery capacity or ambient temperature.
