Open Short
Pinpoint open circuits.
-
Product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
-
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
Product
Network Tester
-
PeakTech Prüf- und Messtechnik GmbH
Compact 3½-digit multimeter, developed according to the CAT III 600 V standard with integrated LAN network tester. In addition to the extensive measurement functions for voltage, current and resistance, this model has a fast-reacting continuity test with an acoustic signal and the possibility of performing diode tests. This combination measuring device is a very practical test device that easily shows the correct pin assignment of network cables by comparing a transmitter with the corresponding cable receiver using an LED. Trouble-free checking of cable passage, open, short and cross connect is possible.
-
Product
Automated DC Parametric Curve Tracer
MultiTrace
-
MultiTrace curve tracer is a mid-sized benchtop model supporting pin counts from 216-625 pins and includes the PGA-625 fixture as a standard interface. MultiTrace supports a wide range of test applications: Failure analysis, Reliability testing, Counterfeit device analysis, Nondestructive electrical counterfeit test, Opens, shorts leakage testing (OSL), Post decap electrical inspection, Optical fault localization, ESD testing, Latch-up testing, Supply current measurements, and more!
-
Product
Standard Mechanical Calibration Kit, DC To 7.5 GHz, 7-16
85038A
Mechanical Calibration Kit
The Keysight 85038A calibration kit contains open circuits, short circuits and terminations with both male and female 7-16 connectors and has frequency coverage from dc to 7.5 GHz (usable to 8 GHz).
-
Product
Network Analyzer, Tester, LED
72-9450
-
This cable tester allows for quick and easy troubleshooting of RJ45 and USB cables. Checks for continuity, faulty wiring, open, shorts, straight through or cross pinning of cables.
-
Product
LAN Cable Tester
-
Is a hand-held test instrument that lets you verify and troubleshoot the LAN cable of twisted pair. It displays graph wire-map, opens, shorts, miswires, split pairs and the remote ID number all on one screen.
-
Product
ELECTRONIC CIRCUIT TRACER
PPECT3000
-
*Locate short and open circuits without having to remove plastic panels, molding and carpet*Traces shorts and open wires with visual navigation and sound indicators*Pinpoint shorts, open circuits, switches and breaks in wires
-
Product
Lan CAble Testers
-
TES Electrical Electronic Corp.
Tests a wide range of FTP & UTP cables. Tests for wiring faults such as open, shorted reversed.
-
Product
Milliohm Meter
MO-100
-
Diagnose potential failure with the MO-100, portable battery powered milliohm meter. Quickly check windings opens or shorts in motors, generators and transformers, wire-to-wire connection resistances, heating elements testing and contact resistance in critical electrical connections.
-
Product
Line Tester
CAT 1 TEST
-
Monacor International GmbH & Co.
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
Product
Low Voltage Testers
-
Device used to identify opens and shorts in applications that are driven on low voltages.
-
Product
Impedance Standards and Calibrators
-
Impedance Calibrator is to replace countless single value RCL standards with one calibrator that can switch between the standards like a CD changer in your car. The calibrator contains stable and temperature independent resistance standards, partial capacitance standards and partial inductance standards, simulated by RC T-type passive network. Calibration values of both complex parameters of partial standards are displayed on large LCD screen in preselected pairs of parameters as well as voltage, current and frequency readouts from built-in test signal meter. OPEN and SHORT reference positions are available as well.
-
Product
High Volume Semiconductor Substrate Interconnect Tester
GATS-2100
-
Pre-align *load *CCD camera alignment *electrical test * unload * sort of pass, opens, shorts, and alignment errors.The GATS-2100 concurrent approach provides unmatched volume capability... 2.5 seconds per device. As with all Nidec-Read Test systems, the GATS-2100 offers you the most test technologies for your requirements
-
Product
Cable Testers
-
The CableTool uses TDR (Time Domain Reflectometry) technology to quickly identify an open or a short from 0 to 2,500 feet within a foot of the fault.
-
Product
Network Tester
-
ZhangZhou Weihua Electronic co.,ltd
There is nothing worse than running your drops only to learn that you have a fault in one of the cable runs. Get it right the first time, get it right by choosing and using the right LAN Cable Testers. We offer a variety of cable testers, which are a must have to quickly and easily verify the integrity of Ethernet twisted pair cables. Our LAN testers will test twisted pair cables for open pairs, shorted pairs, reversed pairs, crossed pairs and split pairs. Network cable testers vary in complexity and price, but a basic tester consists of a source of electrical current and a measuring device. After that, cable testers vary in complexity and ability to do various testing.
-
Product
Cable Fault Locator
FaultCaster
-
Low Cost Full specification Professional Digital TDR Measures Distances to Open or Short Circuit Faults Extended Measuring Range to 2000m (6000ft) on all cable types Fast-Edge Step TDR technology for improved range & Resolution
-
Product
Lan Cable Tester
-
Shanghai Beha Electronics Co., Ltd.
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.• The Lan cable tester can verify cable continuity, open,short circuit and miss-wired.• The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.• Auto and manual scan function.• Ground wire test.• Lock status function.• Buzzer sound warning for wire status.• Display: LED indication for wire status.
-
Product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 4 Channel
40-201-004
Fault Insertion Unit
This high bandwidth differential fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
LAN Cable Tester
21-6568-00
-
The Handheld Lan Cable Tester is an intelligent continuity tester for LAN cables, Phone cable and Coaxial cable. Open, short and misswiring are also tested. It provides the installers an ease of use which keeps you from wasting time through complex menus.
-
Product
Time Domain Reflectometers
T3SP Series
-
Teledyne Test Tools T3SP15D stimulates the DUT with true differential signals. The T3SP15D offers fast rise times of 35 ps for spatial impedance resolution (in FR4) of 3 mm, at DUT lengths up to 40 meters and TDR repetition rates up to 10 MHz and uses the same open short load thru (OSLT) calibration standards as vector network analyzers. With their small form factors, light weight, and optional internal batteries, the instruments go anywhere in test labs or in the field at an affordable price.
-
Product
4-in-1 OSLT Calibration Kit, DC to 18 GHz, Type-N (f) 50 Ohm
CK519A
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
PC-NET Cable Tester
PR-09
-
The PC-NET Cable Tester is a portable, stand-alone unit that provides an affordable way to quickly test PC, Network, Telco, Coax, USB and IEEE1394 cables for continuity and wiring configuration for any combination. Open, shorts, miswires and cross-connected wires are detected immediately. The interchangeable connectors boards offers flexibility and convenience easy to read LED instantly indicates good or faulty. The tester is suitable for use by computer dealers and computer hardware outlets.
-
Product
4-in-1 OSLT Mechanical Calibration Kit, DC To 40 GHz, 2.92 Mm (f)
85561A
Mechanical Calibration Kit
Combines an open, short, load, and through standard in a compact unit that is easy to handle and lightweight.
-
Product
Actuation Methods for In-Circuit Test Fixtures
-
Commonly referred to as In-Circuit Test (ICT), loaded board test can be defined as the task of measuring values of components that have been installed on a printed circuit board (PCB). A second basic category of loaded board test measures simple open and shorts on the board to verify manufacturability standards. Circuit Check supports all forms of in-circuit test strategies with its Performance Grade and Value Line test fixtures.
-
Product
LED Tester For Packaging Machine
-
LED-501 is a single crystal packing tester. It can be utilized in electrical test.Two test results. Pass (GO) or fail (NG).Electrical Testing: Forward：VF Reverse：VZ,IRFour-wire measurement and contact resistance in case of deviation.Auto polarity identification and preheat function.Provide OPEN\SHORT count.Compatible mechanical interface.Connected with computer for measurement data collection.
-
Product
Telemetry Transmitter
TT22 Series
-
Systems Engineering & Management Company
The TT22 series of 0.25W telemetry transmitters are designed to transmit data in the frequency bands covering 1710-1850 MHz or 2185-2485 MHz. These transmitters are true FM, modular, all solid state and are protected for operation into any VSWR, without damage, including open or short circuit.
-
Product
Length Network Cable Tester
SC-8108
-
1. Measure network cable length and determine the distance of breakage point.2. Check wiring error in 5E, 6E, coaxial cable, such as open circuit,short circuit, jumper wire, reverse connection .3. Portable unit with long battery life (wait-case 50 hours).4. Automatically time-delay shut off.5. Self-checking and automatically compensate any change in battery capacity or ambient temperature.
-
Product
Standard Mechanical Calibration Kit, DC To 9 GHz, Type-N, 50 Ohm
85032F
-
The Keysight 85032F calibration kit contains precision 50 ohm type-N standards used to calibrate Keysight network analyzers. Standards include fixed terminations, open circuits, and short circuits in both genders. This kit is specified from dc to 9 GHz.
-
Product
Stand Alone Low Voltage Testers
-
Low voltage testers are a special type of device used to identify opens and shorts in applications that are driven on low voltages.
-
Product
LAN Cable Tester
21-6566-00
-
The Handheld Lan Cable Tester is an intelligent continuity tester for LAN cables, Phone cable and Coaxial cable. Open, short and misswiring are also tested. It provides the installers an ease of use which keeps you from wasting time through complex menus
