Automated X-ray Inspection
See Also: AXI
-
Product
X-ray Windows
-
X-ray devices have become ubiquitous in the marketplace. The X-ray device market is divided into Portable and Stationary product types. The Market is also divided by technologies like Analog, Computed Radiography (CR) and Digital Radiography (DR). The Digital Radiography market is further segmented into Flat Panel Detectors (FPD) and High Density Line Scan Solid State Detector. The applications include at a minimum; Medical, Non-Destructive Testing, and Security Detection has driven the rapid spread of X-ray instruments including a myriad of handheld devices.
-
Product
X5 Pack X-Ray Inspection
-
Designed to be integrated into line with built-in automatic reject and available in 300, 500 and 600 mm belt width models, the X5 Pack is perfect for a variety of unpackaged and packaged products.
-
Product
Test Automation Systems
iTest
-
Our iTest family of test automation systems provide a full range of capabilities, allowing you to purchase just the right solution for your application without having to overbuy.
-
Product
RF Automated Accelerated Reliability Test Station (AARTS)
RF-HTOL
-
The RF Automated Accelerated Reliability Test Station (AARTS) systems are designed to stress devices with RF, DC, and thermal stimulus. The systems were designed from their inception to include RF stimulus - it was not added as an after-thought. Hence, the software and hardware are fully integrated and provide full-featured support.
-
Product
Automated Headlight Tester
VLT 0936/MK2
-
Fully computerized controlled CCD Head-light Beam Tester, with fully automated vertical and horizontal movements, with automated searching of the hot spot of the beam. This robot type Headlight Beam Tester is connected to the Vehicle Test Lane Computer system and displays instructions and results to one of the large overhead SVGA monitors of the Test Lane.
-
Product
X-Ray Detector
Cmosaix CMX4343
-
The technology used for the Cmosaix CMX4343 x-ray detector is based on a large array of CMOS cameras and sophisticated mathematical algorithms that produce superior X-ray imaging and enable new applications that were not possible before, at a fraction of the cost of existing technologies.
-
Product
PXI Instrumentation Modules For Automated Test Systems
-
PXI-based test systems often require a variety of general-purpose instrumentation such as digital I/O, waveform generators, voltage & current sources and DUT power supplies.
-
Product
Automated Video Quality Control
VQFlow
-
Automated video quality control, what content preprocessing, video post production and video service providers are asking for, is now available and ready to be integrated with any ingest or content management system.
-
Product
Automated Filter Tester
3160
-
Automated Filter Tester 3160 is the most advanced automated tester available for challenging filters and filter media with submicrometeraerosols. It can be used to test both low- and high-efficiency filters and filter media, up to 99.999999% efficient (eight 9’s),or penetrations down to 0.000001%. The 3160 uses a bank of atomizers and the TSI Electrostatic Classifier to challenge a filter or filter media with known-size, monodisperse particles.
-
Product
Probes for Tube Inspection
-
Probes for tube inspection are lightweight but solidly constructed eddy current, remote field, magnetic flux leakage, and IRIS ultrasound. These probes are used for ferromagnetic or non-ferromagnetic tube inspection applications.
-
Product
Test Automation Service
-
Do you still use manual methods to test your applications? Does your competition test and effect multiple releases in the time you do one? Automating your testing processes will significantly speed up your release cycles. Automated software testing (also called test automation) is very simply put, a process where software tests software. Predefined automation tools run the test suite and return reports on critical outcomes. All this automation testing happens with minimal human intervention.- Test automation is faster, more precise and allows quicker releases- All testing processes (functional, performance, etc) can be automated- Test automation efficiency lies in choice of reusable and scalable testing tools & frameworks- Automation of testing processes is the foundation and minimum requirement of CD/CI and DevOps
-
Product
Automated Inline In-Circuit Test Solutions
-
Automated versions of Teradyne’s TestStation systems are designed for short takt time automated lines. The TestStation Automated Inline Handler, coupled with a TestStation Test Insert forms a combined integrated solution for any mix, any volume PCBA manufacturing.
-
Product
Defect Inspection and Review
-
KLA’s defect inspection and review systems cover the full range of yield applications within the chip and wafer manufacturing environments, including incoming process tool qualification, wafer qualification, research and development, and tool, process and line monitoring. Patterned and unpatterned wafer defect inspection and review systems find, identify and classify particles and pattern defects on the front surface, back surface and edge of the wafer. This information allows engineers to detect, resolve and monitor critical yield excursions, resulting in faster yield ramp and higher production yield.
-
Product
Simultaneous Wavelength Dispersive X-ray Fluorescence Spectrometer
Simultix 15
-
Multi-channel simultaneous wavelength dispersive X-ray fluorescence (WDXRF) spectrometer system, the Simultix 15 high-throughput WDXRF spectrometer. Analyze beryllium (Be) through uranium (U) in almost any sample matrix. The most important metrics for automated process control are precision, accuracy and sample throughput. With up to 30 (and optionally 40) discrete and optimized elemental channels and 4 kW (or optionally 3 kW) of X-ray tube power, Simultix 15 delivers unparalleled analytical speed and sensitivity.
-
Product
Inspection and Maintenance
-
Sensors' EMISSIONS INSPECTION ANALYZERS have a long-standing history for exceeding international standards with compact, portable, and cost-effective systems.
-
Product
Thick Film Inspection
785
-
For thicker coatings such as coal tars, extruded and tape coatings, the Model 785 has a range of infinite voltage settings from 1,000 to 15,000 volts.
-
Product
RFID Label Inspection System
Eurotech RFID FS
-
The Eurotech RFID FS RFID accurately rewinds rolls of RFID labels and validates their receptivity by running them through the Voyantic Tagsurance RFID inspection system. The unit allows stopping at a predetermined editing spot for the removal and replacement of the defective piece, as well as indicating defective labels by a mark printed by an inkjet system integrated with the machine. Adjustment of the closed loop tension control system can be made through adjusting the parameters on the software that control the servo motor control system. This gives the customer a virtual infinite range with which to wind their labels without cracking the inlay or antenna. As well accurate web adjustment and guidance is provided with a web guide system complete with an ultrasonic sensor. The Eurotech RFID FS RFID label inspection system is equipped with the Voyantic Tagsurance for testing the performance of RFID tags. This is done by verifying that the tag responds to commands on its whole operational frequency range, which means testing the tag on multiple frequencies, also outside the RFID reader frequency. Accurate power output combined with the Voyantic Snoop Pro antenna, optimized for testing tags inline at high speed, allows defining precise acceptance criteria and achieving stable quality.
-
Product
Continuous Particulate Monitor with X-ray Fluorescence
PX-375
-
There has been a growing concern regarding particulate matter (PM) pollution and its effects on health. For effective preventative measures, the determination of source PM concentration is extremely important. Therefore, indication of PM and elemental concentrations is critical. The PX-375 analyzer employs automatic sampling, continuous on-line PM quantitative and qualitative analysis for rapid air pollution measurements.
-
Product
X-Ray Inspection
-
X-ray inspection systems are used wherever defects need to be detected by non-destructive means. The spectrum of use is broad and ranges from quality controls for complex assemblies, to the testing of materials for cracks and air inclusions, to foreign matter inclusions and shape deviations. The trend toward miniaturization, higher packing densities, and the relocation of components to the interior of the assembly require precise X-ray inspections that detect hidden defects quickly and reliably. X-ray systems from Viscom are used for the inspection of series assemblies as well as sampling and prototype controls. They take care of typical inspection tasks in concealed areas such as void controls, THT filling level measurements, and HIP inspections. At the same time, the systems reliably determine defect features such as coplanarity and polarity – at high inspection speeds and in a cost-effective way.
-
Product
Field Evaluation And Special Inspections
-
Nemko offers Field Evaluation and Special Inspection Services in the US and Canada as a fast and economical alternative to traditional product safety certification.
-
-
Product
Measuring And Inspection Systems For Rubber And Tires
-
The rubber processing industry, as well as the tire production process is supported by Micro-Epsilon with a range of systems for inspection, monitoring and control of miscellaneous processes.
-
Product
LXI-Certified 1.85mm Automated Tuners 8.0 to 65.0 GHz
MT985 Series
-
Maury''s MT985AL01 LXI controlled automated tuners are optimized for a broad class of in-fixture and on-wafer applications requiring flexibility, broad frequency coverage and ease of use. Based on Maury''s proven non-contacting probe technology, these high-performance tuners evolve beyond outdated contacting probe technology to deliver high VSWR with superb accuracy and reliability.
-
Product
Terahertz Imager for Material Inspection
T-SENSE FMI
-
This highly efficient technology is based on the most recent research results. Production can be monitored and controlled at various levels. T-SENSE FMI uses millimeter waves in the lower terahertz range with no health risks involved. This means that the equipment can be used anywhere and for several purposes without the need for radiation protection.
-
Product
Testing, Inspecting & Cleaning Kit
KI-TK033
-
850/1300 nm source & power meter, inspection microscope, cleaning materials. Interchangeable MPO, SC, LC connectors
-
Product
AUTOMATED TEST STAND DESIGN
-
Automated test systems may be as simple as a laptop with a DAQ module or a stand-alone controller, but they typically require a mix of off-the-shelf and custom hardware. All that hardware is integrated and wired into a test stand. Portable or mobile test stands are ideal for in-the-field research and development and servicing of multiple laboratories or manufacturing lines. Test stand access to the front panels of hardware and subcomponents allows manual configuration of non-automated settings. Quick disconnects, cable harnesses, and easy access to probes provides efficient setup and tear-down. Expandable or modular rack mount and card base systems facilitate future needs. Ergonomic considerations include keyboard and display placement, along with number of monintors. Safety is always crucial with proper E-stop placement and keeping dangerous elements away from users.
-
Product
X-Ray And Gamma Detector Systems
-
The XR-100CR is a new high performance x-ray detector, preamplifier, and cooler system using a thermoelectrically cooled Si-PIN photodiode as an xray detector. Also mounted on the 2-stage cooler are the input FET and a novel feedback circuit. These components are kept at approximately -55 °C, and are monitored by an internal temperature sensor. The hermetic TO-8 package of the detector has a light tight, vacuum tight thin Beryllium window to enable soft xray detection. The XR-100T-CdTe represents a breakthrough in xray detector technology by providing “off-the-shelf” performance previously available only from expensive cryogenically cooled systems. The XR-100-CdTe is also suited for measuring gamma rays.
-
Product
Software Test Automation Solution
ZAPTEST
-
ZAPTEST is a software test automation solution for testing Mobile; Web; Desktop applications Cross-Platform. ZAPTEST allows testing of any GUI based software on any modern OS, mobile or conventional including iOS; Android; WinMo; Blackberry; Windows; Mac; and Linux, and supports testing of Agile and CI development.
-
Product
Line Automation Equipment
5000 Series In-line Handler
-
The Circuit Check 5000 Series In-line Handler is an integrated inline solution that combines automation, fixturing and measurement hardware in addition to other in-line PCBA probe based test stations, while adding a standardized quick change fixture interface. The 5000 series in-line is a unified solution that is software and hardware agnostic, enabling adaptability to a variety of off-the-shelf lower cost ICT, flash and functional test software and hardware.
-
Product
Inspection Solutions
-
Entire range of optical inspection systems. From the SPI machine (SPI inspection) for checking solder paste printing, to an inline AOI for THT or SMD-assembled PCBA, to AXI machine for BGA x ray inspection. And furthermore, GÖPEL electronic's AOI PCB inspection can be used for conformal coating inspection (CCI) of various protective coatings applied to boards.
