UUT
assures a constituent's interoperability in a system.
See Also: Unit Under Test, DUT, System Under Test
-
Product
Pylon ITA Mount Linear Testfixture Cassette and ITA Frame Not Included, UUT 306 x 248 mm
MG-02 VGR12
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with aluminum backpanel for a Genrad VGR12 Pylon frame• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 306 x 248 mm (wxd)• Outer dimensions: 470 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for changeable cassette
-
Product
Manual Fixture Kit with Changeable Cassette, Max number of probes (2N) 500 units, Max UUT 230 x 175 mm (wxd)
CMK-06
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Manual Fixture Kit With Changeable Cassette, Max number of probes (2N) 1000 units, Max UUT 580 x 400 mm (wxd)
CMK-04
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 580 x 250 mm (wxd)
CMCSK-03-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 580 x 400 mm (wxd)
CMCSK-04-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Linear Testfixture Cassette and VPD ITA Frame Not Included, UUT 306 x 248 mm
MG-02 VPC G12
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable CEM Backpanel for VPC G12(x) ITA frame mount• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 306 x 248 mm (wxd)• Outer dimensions: 470 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for changeable cassette
-
Product
ICT/FCT-Fixtures, Max UUT 370 × 300 mm (wxd)
CK-2-228X (Small IF) / 230540
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
PXI 5A Fault Insertion Switch 5-Channel
40-196-101
-
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
Product
AC Source
AFV-P
-
Intepro’s AFV-P Series is a programmable AC/DC output power source with precision measurement and control. This compact power source comes in four power levels, 600VA, 1250VA, 2500VA and 5000VA, providing clean power with distortion less than 0.3% at 40-100Hz. The AFV-P series delivers output voltage from 0 to 310VAC and frequency from 40 to 500Hz or 15 to 1000Hz with the high frequency option. It is ideal for commercial, defense and aerospace test applications from design verification, quality assurance, ATEs. The AFV-P Graphical Users Interface software makes it easy to setup complex testing of the AC input to the UUT.
-
Product
SWB-2817, 16x22, 0.3 A, Reed Matrix Module for SwitchBlock
781420-17
-
16x22, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2817 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
MIL-STD-1553 Fiber Optic Bus Extender
FO-1553
-
Avionics Interface Technologies
Extends MIL-STD-1553 bus access to over 1 mile for remote access - Dual redundant, single and dual stream options available - Both Transformer and Direct coupling modes supported - Uses fiber optic 1.0625 Gbps data rates for low latency over long distances - Optical signaling is not affected by electrical noise and interference - Simple and easy to use solution, no software setup or configuration required - Ideal for applications where test equipment is separated from UUT
-
Product
Chassis
-
With over 20 different chassis configurations, our Smart PXI chassis product line (3U chassis, 6U chassis, 3U/6U chassis) offers the most features, slot configurations, UUT interface options, system power, and embedded / external controller options in the industry.
-
Product
Configurable High-Density Switch Matrix PXI Card
GX6384
-
The GX6384 3U PXI multiplexer switch card provides users with the ability to switch and interface tester resources to multiple UUT connections. The card is available in three different configurations, supporting 32 x 2, 32 x 4, and 32 x6 switch configurations.
-
Product
AC and DC Electronic load
63800 series
-
The Chroma 63800 Loads can simulate load conditions under high crest factor and varying power factors with real time compensation even when the voltage waveform is distorted. This special feature provides real world simulation capability and prevents overstressing thereby giving reliable and unbiased test results. The 63800's state of the art design uses DSP technology to simulate non-linear rectified loads with its unique RLC operation mode. This mode improves stability by detecting the impedance of the UUT and dynamically adjusting the load's control bandwidth to ensure system stability. Comprehensive measurements allow users to monitor the output performance of the UUT. Additionally, voltage & current signals can be routed to an oscilloscope through analog outputs. The instrument's GPIB/RS232 interface options provide remote control & monitor for system integration. Built-in digital outputs may also be used to control external relays for short circuit (crowbar) testing.
-
Product
Combination Board Tester
V250 / V250PXI
-
Qmax Test Technologies Pvt. Ltd.
V250 / V250PXI is designed as a Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities and conventional PCBs. An In –Circuit device test by configuring Pin Drivers to High Current Pin Driver mode and interface to the UUT either through Clips / Probes or nail bed and on board clock disable HW feature are the all time favorite . The in-built high frequency 14bit Analog Driver / sensors synchronized with digital drivers for covering analog / mixed signal devices with high degree of accuracy.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP6T, 6 GHz, 50 Ω, SMA, Failsafe
42-784B-001
-
The single slot remote multiplexer versions occupy less PXI panel space and allow the microwave relays to be placed closer to the UUT and other RF test equipment. In some applications it can shorten the length of RF cable runs and improve system performance. The remote multiplexers are supplied complete with a 1.5 m interface cable.
-
Product
PCI Express Gen 3 Test Backplane
SKU-015-01-PCIe
-
PCI Express Backplane was designed to support a variety of modern PCI Express board’s production testing and debugging. The backplane expands the Host computer into four x16 PCI Express slots via 10 ft. CAT7 data and 10-pin flat Power control cables. PCI Express Backplane and UUTs (unit under test – add-in PCI Express board) are powered by a standard ATX power supply connected to the backplane via 24 and 8 pin power connectors located on the backplane.
-
Product
SWB-2814, 8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock
781420-14
-
8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock - The SWB‑2814 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
RWR ATE MKII
MS 1111
-
Automatic Test Equipment (ATE) MKII is a customized tester, built to carry out LRU and card level testing for TARANG systems of all platforms. The purpose of ATE is to provide a user-friendly environment to test the LRUs and sub-systems (individually) for their functionality, perform specific tests of each LRU / sub-system and Card Level Testing. The card level testing facilitates troubleshooting down to a faulty signal flow path. The UUT tests are carried out by injection of the stimuli generated by the computer or the programmable test equipments and the responses from UUT / test equipments are feedback to the computer for evaluation and generation of reports.
-
Product
PXI 16x4 Signal Insertion and Monitor Matrix
40-525A-002
-
This is a PXI signal insertion and monitor matrix with switched pass thru connections on both X and Y axis. It is also available in a 34x4 format and can be used for signal insertion and monitoring purposes on connections between the UUT and test system.
-
Product
SWB-2810, 4x43, 1 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-10
-
4x43, 1 A, Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2810 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Pin-Mapping for Custom Connectors, Test Fixtures, UUTs | Cable & Harness Testers
PinMap™
-
Check out this fast and super-easy pin-mapping process enabled by our optional CableEye® PinMap™ software. Map as fast as you can move the probe from one pin to the next. Use on your custom connectors, test fixtures, specially-built connector panels, or pigtail adapters to your CableEye tester.
-
Product
Benchtop Automated Functional Test
midUTS
-
Combining bench-top portability with powerful automated test functionality, the midUTS is an extremely versatile yet cost-effective solution for your electronics functional test needs. Comprised of high-performance commercial-off-the-shelf (COTS) instruments, along with Bloomy’s medium-density signal-routing PCBAs, a built-in or USB-connected PC, and a pair of high-integrity, production-grade cables connected to an adjacent benchtop fixture, the midUTS can be used in engineering for PCBA bring up, as well as scaled to manufacturing to perform high-volume PCBA and sub-assembly functional testing. It is also ideal for depot diagnostic test, debug, and repair of field returns. The two mass-interconnected cables connect the midUTS to as many as 320 test points on the unit under test (UUT), supporting an extreme wide variety of products using bed-of-nails as well as cable-connected UUT test fixtures. Most importantly, the midUTS helps you automate sequences of functional tests using NI TestStand and the Bloomy EFT Module for TestStand. This ideal balance between powerful features and affordable cost allow you to automate earlier in the product development lifecycle, substantially increasing product quality and minimizing time-to-market!
-
Product
Test Extension Boards
XJIO
-
The XJIO boards are expansion units that enable you to improve the test coverage for a Unit Under Test (UUT) by verifying the signals right through to the external connections. They will integrate with your XJTAG test system to provide access to otherwise inaccessible areas of your circuit. With a range of digital and analogue I/O pins on the board, you can improve fault isolation, verify power rail levels, and dispense with costly custom test jigs - even for non-JTAG boards.
-
Product
Linear Testfixture (Cassette Not Included), UTT 194 x 170 mm
MG-06
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 194 x 170 mm (wxd)• Outer dimensions: 400 x 354 x 70 x 140 mm (wxdxh1xh2)• Designed for changeable cassette
-
Product
In-Circuit Tester Integration
-
The benefits of boundary-scan are noticed in all phases of a product life cycle. By coupling the power of Corelis boundary-scan tools with an In-Circuit Tester (ICT), a complete, integrated solution is available that offers the best advantages of both technologies.Boundary-scan operates as the perfect companion to ICT. Boundary-scan is capable of testing areas of printed circuit board assemblies that are difficult to access due to physical space constraints and loss of physical access, which is often due to fine pitch components such as Ball Grid Array (BGA) devices. Conversely, the ICT is able to check the non-boundary-scan compatible portion of the unit under test (UUT) such as analog.
-
Product
Linking Conveyor 765mm
AM307
-
The high performance linking conveyor from 6TL is an option for the users of 6TL36 handling technology. The 6TL36 needs a high performance conveyor in the inlet, that is able to synchronize with the conveyor inside the handling system, so that the UUT can be stopped without phisical stopper, to further proceed with the contacting operation.
-
Product
LASAR Post Processor, Run Time And Diagnostic Test Solution
DtifEasy Series
-
DtifEasy is a full-featured tool set for importing, converting, and executing IEEE-1445 compliant digital test vectors generated by a LASAR simulation. All four IEEE-1445 file types - UUT model group, Stimulus and Response group, Fault Dictionary group, and Probe group are supported by DtifEasy; providing the user with the ability to execute go/no-go, fault dictionary, and guided probe sequences. DtifEasy supports MTS' 3U PXI GX529x series of dynamic digital instrumentation to 200 MHZ as well as the 6U PXI GX5960, 50 MHz digital instrumentation. All of these instrument families are compatible with the digital logic probe.
-
Product
96 Channel DPST Relay And Control PXI Carrier Card
GX6196
-
The GX6196 is a 6U PXI switch and control board that can be used to create custom switching, signal conditioning, or specific UUT control interfaces. The board provides 96, 2 pole, form A relays, 8 digital I/O lines, and a serial digital interface. All of these resources are available via (5) inter-board connectors which interface to the user defined daughter / mezzanine board. The mezzanine board provides all connections to the unit under test (UUT) via two 78 pin D-sub connectors. The GX6196 is supplied with a front panel which accepts (2) 78 pin D-sub connectors.
-
Product
QuadraPaddle 90 Series Modules
-
The versatility of VPC's QuadraPaddle twin female contacts provide four beams per end to ensure signal integrity from instrumentation to the Unit Under Test (UUT).Twin male contacts interconnect to ribbon cable, headers, and other standard connectors.Makes system configuration a simple “plug & play” operation and delivers high density, high performance interconnectivity at a lower cost per point.
