Regulated DC Power Supplies
Clip unregulated (varying) source of DC voltage at a specified level to supply regulated (steady) voltage to a load. (allaboutcircuits.com)
-
product
Power Supply, 100V, 33A, 3300W
N8739A
Keysight basic DC power supplies offer essential features for a tight budget. The Keysight N8739A is a 100V, 33A, 3300W, single output power supply in a small 2U package. It offers flexible AC input options, analog/resistance control of output voltage and current, as well as parallel and series connection of multiple supplies to achieve more output current or voltage respectively.
-
product
10 MHz To 54 GHz USB Wide Dynamic Range Average Power Sensor
U2056XA
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis
-
product
Differential Sensor, Wide Dynamic Range, 100 MHz
CX1105A
The CX1105A ultra-low noise differential sensor is a dedicated accessory for the CX3300 series and enables dynamic current measurements from 1 μA to 100 A under up to 100 MHz bandwidth with existing shunt resistors on your test board.
-
product
Power Sensor and SNS Noise Source Cables (3 m/10 feet)
11730B
The Keysight 11730 series power sensor cables are used with the 8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements.
-
product
Power, Patchcord, ITA, 36", Mini Power, 16 AWG White Teflon, Single Ended
7-244916000-036
Power, Patchcord, ITA, 36", Mini Power, 16 AWG White Teflon, Single Ended.
-
product
VDI Erickson PM5B MM–Wave Power Meter with W-Band Sensor, Optional Tapers to 1.5 THz
N1913PM5B
N1913PM5B is a Virginia Diodes, Inc./Erickson PM5B calorimetric mm-wave power meter, with a W-Band sensor for power measurement over a frequency range of 75-110 GHz.
-
product
Power, Patchcord, Receiver, 72", Micro Power, 12 AWG White, Single Ended ( 22 Amps)
7-252912000-072
Power, Patchcord, Receiver, 72", Micro Power, 12 AWG White, Single Ended ( 22 Amps).
-
product
E-Series Peak and Average Power Sensor, 50 MHz to 6 GHz
E9321A
The E9321A power sensor has a 300 kHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on TDMA wireless formats such as NADC, GSM and EDGE.
-
product
High-Performance Autoranging DC Power Module, 20V, 50A, 300W
N6753A
The Keysight N6753A is a high-performance, autoranging DC power module that offers speed and accuracy for test optimization.
-
product
EPM Series Dual-Channel Power Meter
N1914B
The N1914B EPM series dual-channel average power meter provides repeatable and reliable results for bench/rack and field applications.
-
product
DC Power Module, 100V, 1A, 100W
N6746B
This module is used in both the small, multiple output 1U high N6700 Low-Profile Modular Power System (for ATE systems) and the multiple output N6705 DC Power Analyzer (for bench testing). GPIB, LAN, USB, and LXI compliance are standard. Select from more than 20 different DC power modules, ranging in capability from basic to high precision, and in power from 20 - 300 W.
-
product
P-Series Single Channel Power Meter
N1911A
30 MHz video bandwidth Single shot real time capture at 100 M sample/s per second Key Measurements: - peak, average, peak-to-average ratio, rise time, fall time and pulse width22 Predefined formats: WiMAX, DME, HSDPA, etc. One screen view for pulse measurement analysis: Auto Scale, Auto Gate, Rise/Fall Time, Duty Cycle, etc. Internal Zeroing and Calibration while connecting to the DUT Bench Vue software enabled
-
product
10 MHz to 50/53 GHz USB Wide Dynamic Range Average Power Sensor
U2055XA
The Keysight U2055XA is a fast, accurate and wide dynamic range 10 MHz – 50/53 GHz USB average power sensor.
-
product
DC Power Supply, 35 V, 1 A, 35 W
E36104B
The Keysight E36104B is an accurate, 35 V, 1 A, 35 W compact power supply for your bench or system.
-
product
Intelligent Power Monitor
iPM
NAI’s iPM is an Intelligent Power Monitor that provides a precise, instrument grade, digital analysis of input power lines. This advanced, DSP-based unit monitors single-phase, 3-phase 4-wire wye, or 3-phase Delta power lines at various input voltage levels and frequencies.The iPM is equipped with an EIA RS485-compatible serial communications interface that permits additional control functions and readout of diagnostic data, and features a Background Built-in-Test (BIT) that constantly monitors the health of unit hardware and software. This power monitor is designed and qualified to the most stringent performance and environmental requirements, and is ideally suited for rugged defense and industrial applications.
-
product
Programmable Linear DC Power Supply, 2 Output, 0-32V/0-3A
T3PS23203P
Programmable Linear DC Power Supply, 2 Output, 0-32V/0-3A.
-
product
200W Power Supply, 25V, 7A or 50V, 4A
E3634A
Keysight basic DC power supplies offer essential features for a tight budget. The single output, 120-200 W, GPIB, E3632A-E3634A provide dual range outputs; small, compact size for bench use; low output ripple and noise; as well as built-in measurements and basic programmable features with GPIB and RS232 interface. The Keysight 200W, GPIB, single output E3634A is a high performance supply optimized for manual and basic automated testing; and, with a combination of benchtop capabilities and system features, it is designed to help improve measurement quality and reduce test time.
-
product
Industrial AC Power Supply 2U Form Factor, 350W
APS-9235XU
- Power (typical): 350W- AC Voltage Input Range: Universal- Certifications: UL/cUL/TUV/CCC- Dimensions: 215 x 100 x 70 (mm)
-
product
2,000 Watt AC/DC Standalone EMI Compliant Power Supply
56XS1
NAI’s 56XS1 is a conduction-cooled, 2,000 Watt AC/DC Power Supply that converts either 3-phase, AC input or +270 VDC input into a single DC output at 2,000 Watts.
-
product
500-Watt AC/DC Power Supply
56TS1
NAI’s 56TS1 is a 500 Watt AC/DC Power Supply that accepts a 3Ø AC input or a +270 VDC input. This COTS unit provides full-power output power at a baseplate temperature of +85° C.
-
product
DC Power Module, 8V, 12.5A, 100W
N6742B
The Keysight N6742B is a 100 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
product
Precision DC Power Module, 60V, 20A, 300W
N6764A
The Keysight N6764A is a 300 W precision DC power module that provides low noise, and precise control and measurements in the milliampere and microampere region with the ability to simultaneously digitize voltage and current, and capture those measurements in an oscilloscope-like data buffer.
-
product
10 MHz – 18 GHz USB Power Sensor
U2000B
U2000B USB Power Sensor measures average power over the frequency range 10 MHz to 18 GHz and power range -30 dBm to +44 dBm.
-
product
DC Power Module, 35V, 3A, 105W
N6744B
The Keysight N6744B is a 105 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
product
200W Autoranging Power Supply, 60V, 10A
E36232A
E36232A provides more useable power with autoranging architecture in a bench friendly design with full programmability; LAN, USB and optional GPIB interface.
-
product
DC System Power Supply, 8 V, 90 A, 720 W
N5742A
The single output, 720 W N5742A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current
-
product
Power Monitors
NAI''s Power Monitors are used to monitor voltage, frequency, phase characteristics, or phase rotation of single- and three-phase power lines. Specifically designed for rugged defense and industrial applications, these Power Monitors meet the most stringent performance and environmental requirements.
-
product
Power Supply Series
NGE100B
The R&S®NGE100B DC Power supply series consists of robust, high-performance, affordable instruments. They offer high efficiency combined with low ripple plus a variety of comfort functions that are not usually found in this class of power supplies.
-
product
Power Sensor
8483A
The 8483A diode power sensor measures average power over the frequency range 100 kHz to 2 GHz and power range -30 to +20 dBm (50 dB dynamic range).
-
product
80W Power Supply, 8V, 8A or 20V, 4A
E3644A
Keysight basic DC power supplies offer essential features for a tight budget. The single & dual output, 30-100 W GPIB E3640 series provide small, compact size for bench and system use; low output ripple and noise; and built-in measurements and basic programmable features. The Keysight 80W, single output E3644A is a stable and reliable power supply for benchtop and basic automated test applications, and enables versatile solutions for tests that require moderate speed and precision with both GPIB and RS232.
