Phantom Power
-
Product
Save A Watt® Phantom Power Indicator
P4190
-
The Save A Watt® Phantom Power Indicator offers an easy way to save money by showing you how much power your electronics are using in standby mode. Whether it’s a cell phone charger using 5 watts, or a video game using up to 15 watts, this simple device will show you how much they’re using.
-
Product
Portable Three Phase Phantom Load Power Source
SY2103
-
Hong Kong Songyang Industrial Ltd.
The new SY2103 series portable three phase phantom load stable power source, designed from new digital wave compound technology and according to International Standard, is newly intelligent equipment for energy meters. The equipment includes voltage/current source & standard meter, operated easily through front panel to preset directly all data of meter under test and test process.
-
Product
Type 1 Phantom Powered Measurement Microphone
MK224PH
-
The MK224PH Type 1 phantom powered measurement microphone system offers a cost effective solution to acoustic measurements from phantom powered sources. Frequency Response: +/-2dB (8 Hz to 18kHz). Sensitivity: 50 mV/Pa (-26 dBV/Pa)typ. Dynamic Range 3% THD: 14dBA-145dB.
-
Product
Log Periodic Dipole Array
ALP650
-
Skeletal design remote antenna with onboard amplifier ideal for long cable runs, phantom powered from Venue, UMC16 or Bias T. The ALP Series antennas are a Log Periodic Dipole Array (LPDA) design that provides a useful directional pattern over a broad frequency bandwidth.
-
Product
RF Modules
-
Infotainment systems have to deal with a several RF signals, starting from world radio standards but extending to mobile communication, GPS & WLAN. Most of the H.U. RF connections provide phantom power to active antennas that should be tested at different loading conditions (on more values, yet different case by case).
-
Product
Cable Tester
CT100
-
The intelligent, CPU-controlled CT100 accepts virtually any connector type: XLR, mono and TRS phone ( 1 /4 ", 1 /8 ", TT), RCA and MIDI. It shows which input pin is connected to which output pin. Separate LED's indicate proper shield connection and phantom power presence. The CT100 also offers an installed cable test mode and a continuity check plus a test tone generator.
-
Product
Plug-On Transmitter
HMa
-
This unique plug-on transmitter design will ideally match any microphone or line level source via a standard XLR connector. Phantom power is selectable at 5, 15 and 48 volts, or can be turned off for use with dynamic microphones and line level signal sources.
-
Product
RC-50 Artificial Phantom Load with Power Factor
480
-
The RC-50 Artificial Phantom Load with Power Factor (Catalog No. 480) has been re-designed to meet the most exacting requirements. It operates from a single phase source and will deliver current at either unity or 50% power factor at all full load ranges.
-
Product
Microphones
-
All these measurement microphones have a XLR connector and require a phantom power. They can be connected to specially equipped soundcards or pre-amplifiers, only.
-
Product
Telephone Line Tester for ISDN Lines
1EA065
-
ISDN line checker shows the correctness of your ISDN So bus line connections. Indication of the problem is presented with 4 LED (combination of them shows different states and working conditions of the ISDN So bus). The tester uses Phantom power - no need for additional power supplay.
-
Product
Measurement Microphones
-
All microphones are omni-directional and 48V phantom powered. The XL2 Analyzer microphones include an electronic data sheet. The Automated Sensor Detection (ASD) of the XL2 automatically reads this data sheet, and recognizes the microphone model, sensitivity and calibration data. This ensures accurate measurement results.
-
Product
Phantom Powered Measurement Microphone System
7052PH
-
The 7052PH Type 1.5TM phantom powered measurement microphone system offers a cost effective solution to acoustic measurements from phantom powered sources. Type 1.5TM - a superior Type 2. Frequency Response: <3 Hz to > 20kHz typ.(capsule). Sensitivity: 22 mV/Pa (-33 dBV/Pa)typ. Dynamic Range (capsule) 1% THD: <20dBA-150dBSPL (Capsule).
-
Product
Amplifier, Switch and Test Box
CLIOQC Model V
-
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
-
Product
100W Dual Output Power Supply Two 35V, 1.4A or 60V, 0.8A
E3649A
-
Output ratings (@ 0C to 40C) 2 outputs Range 1: 0 to 35 V / 1.4 ARange 2: 60 V / 0.8 A Programming accuracy (@ 25C 5C), (% output + offset)Voltage: <0.05% + 10 mV (<0.1% + 25 mV for output 2 of E3646/47/48/49A)Current: <0.2% + 10 mARipple & noise 20 Hz to 20 MHz Normal Mode Voltage: <8 mVpp / 1 mVrms Normal Mode Current: <4 mArms Common Mode Current: <1.5 uArms Readback accuracy (@ 25C 5C), (% output + offset)Voltage: <0.05% + 5 mV (<0.1% + 25 mV for output 2 of E3646/47/48/49A)Current: <0.15% + 5 mA (<0.15% + 10 mA for output 2 of E3646/47/48/49A)
-
Product
Precision DC Power Module, 60V, 17A, 500W
N6766A
-
The Keysight N6766A is a 500 W precision DC power module that provides low noise, and precise control and measurements in the milliampere and microampere region with the ability to simultaneously digitize voltage and current, and capture those measurements in an oscilloscope-like data buffer.
-
Product
FPD Tester Power Module
67393-120-480
-
The 67393-120-480 FPD Tester Power Module is a new generation of small, stable, high reliability AC to DC power supply. It adopts compact mechanical design and uses Chroma FPD Tester for signal input/output that can provide a total solution for testing the signal, control and power of diversified panels.
-
Product
E-Series Average Power Sensor
E9300B
-
Measure the average power of all modulation formats Wide dynamic range power measurements from -30 dBm to +44 dBm Frequency range 10 MHz to 18 GHzLow SWR for reducing mismatch uncertainty Calibration factors, linearity and temperature compensation data stored in EEPROM Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
Product
Wideband Power Sensor, 50 MHz to 40 GHz
N1924A
-
The Keysight N1924A peak power sensor provides peak, peak-to-average ratio, average power, rise time, fall time, maximum power, minimum power and statistical data of peak signals.
-
Product
Mini Power, ITA, 36", 50u Gold (22 Amps), 16 AWG White Teflon (19 Amps), Single-Ended
7-243916000-036
-
Mini Power, ITA, 36", 50u Gold (22 Amps), 16 AWG White Teflon (19 Amps), Single-Ended
-
Product
10 MHz to 40 GHz LAN Wide Dynamic Range Peak and Average Power Sensor
L2064XA
-
The Keysight L2064XA is a fast, accurate and wide dynamic range 10 MHz – 40 GHz LAN peak and average power sensor.
-
Product
Waveguide Power Sensor
E8486A
-
Keysight waveguide power sensors are fully compatible with Keysight EPM (E4418B/19B, N1913A/14A), EPM-P (E4416A/17A) and P-Series (N1911A/12A) power meters. The V8486A and W8486A are also compatible with the discontinued or obsolete power meters such as 435B, 436A, 437B, 438A, 70100A, E1416A, E4418A, and E4419A power meters.
-
Product
Industrial Flex ATX AC Power Supply for Mini-ITX Chassis, 250W
APS-925XU (80Plus)
-
- Power (typical): 250W- AC Voltage Input Range: Universal- Certifications: UL/cUL/TUV/CCC- Dimensions: 150 x 81.5 x 40.6 (mm)
-
Product
DC System Power Supply, 80V, 9.5A, 760W
N5748A
-
The single output, 760W N5748A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current.
-
Product
Power, Patchcord, Receiver, 72", Micro Power, 12 AWG White, Single Ended ( 22 Amps)
7-252912000-072
-
Power, Patchcord, Receiver, 72", Micro Power, 12 AWG White, Single Ended ( 22 Amps).
-
Product
Peak And Average Power Sensor, 50 MHz - 18 GHz, 300kHz Bandwidth
E9325A
-
The E9325A power sensor has a 300 kHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on TDMA wireless formats such as NADC, GSM and EDGE.
-
Product
Thermocouple Power Sensors
N8485A
-
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
DC System Power Supply, 20 V, 38 A, 760 W
N5744A
-
The single output, 760W N5744A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current.
-
Product
DC/10 MHz 50 GHz USB Thermocouple Power Sensor
U8487A
-
The U8480 series is Keysight's first power sensor with the capability to measure down to DC (only applicable for U8481A/85A). Now, with an expanded frequency range up to 50 and 67 GHz, the U8480 series allows you to make fast and accurate high frequency power measurements in applications ranging from PNA/MXG calibration to high volume manufacturing.
-
Product
Power Sensor and SNS Noise Source Cable (1.5m / 5 feet)
11730A
-
The Keysight 11730 series power sensor cables are used with the 8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements.
-
Product
10 MHz To 67 GHz USB Wide Dynamic Range Average Power Sensor
U2057XA
-
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
