Polarization Mode Dispersion
Polarization Mode Dispersion
-
Product
10 Micron Wire Grid Polarizer
-
Fabricated from 10 micron diameter tungsten wire, and with a choice of wire spacing starting from 25 microns, these wire grid polarizers are suitable for use from approximately 100 microns (or 3 THz) to longer wavelengths. Please refer to the table below for the standard availability of wire spacing and frame clear aperture / outer diameter.
-
Product
Common Mode Chokes
-
Common Mode Chokes, as the name implies, are designed to attenuate and filter common mode noise within an electric system. The key parameters for a common mode choke are the current rating (to ensure the part does not overheat within the application), the impedance versus frequency (to ensure it is optimized to attenuate the desired frequencies), the isolation voltage (to ensure it meets board level requirements between the line and neutral phases) and safety isolation (to ensure it meets the safety requirements of the end-application). It is important to remember that common mode chokes cannot saturate in the application (under normal use) as they are designed to ensure that the line and return currents are balanced.
-
Product
Dual Polarized Broadband Horn Antennas
-
Linear polarized dual double ridged broadband antenna for receive and transmit applications made of aluminium.
-
Product
Dual Polarized Antennas
-
Dual polarized horn antennas are offered as both standard and custom models with rectangular waveguide interfaces for both horizontal and vertical ports. These dual polarized horn antennas support both linear and elliptical polarized waveforms. When the antenna receives a circular polarized waveform, equal amplitude linear polarized waveforms are output at both horizontal and vertical ports. When two equal amplitude linear polarized waveforms are input into the vertical and horizontal ports, the antenna will transmit a circular polarized waveform. The listed models offer 15 dB nominal gain and 33/28 degrees typical half power beamwidth at the center frequency of the band. They also exhibit 40 dB typical port isolation and 35 dB nominal cross polarization. These antennas cover full waveguide bandwidths within the frequency range of 8.2 to 110 GHz. In addition to the models listed below, models with 10, 20, 23 and 25 dB gain and other frequency bands are also available.
-
Product
Fiber Optical Switch at Single Mode Latching 1310/1550nm 5V with LC/PC Connector
SUN-FSW-1x2
-
Guilin GLsun Science and Tech Group Co., LTD
GLSUN 1x1 Mechanical Optical Switch - Features·Low Insertion Loss·Wide Wavelength Range·Low Crosstalk·Epoxy-free on Optical Path·High Stability, High Reliability·Latching and Non-latchingGLSUN 1x1 Mechanical Optical Switch - Applications·R&D in Laboratory·System Monitoring·MAN (Metropolitan Area Network)·Network Security and Monitoring·OADMGLSUN 1×1 Optical Switch - SpecificationsParametersUnitSUN-FSW-1×1Wavelength Rangenm850±40 / 1300±401260 ~ 1650Test Wavelengthnm850 / 13001310 / 1550Insertion Loss 1,2dBTyp: 0.5 Max: 0.8Typ: 0.4 Max: 0.6Return Loss 1, 2dBMM ≥ 30 SM ≥ 50Crosstalk 1dBMM ≥ 65 SM ≥ 70PDLdB≤0.05WDLdB≤0.25RepeatabilitydB≤±0.02Operating VoltageV3.0 or 5.0DurabilityCycles≥ 10 MillionSwitching Timems≤8Optical PowermW≤500Operating Temperature℃-20 ~ +70Storage Temperature℃-40 ~ +85Relative Humidity%5 ~ 95Weightg14Dimensionmm(L)27.0×(W)12.6×(H)8.2 ±0.2Note: 1 Within operating temperature and SOP.2 Excluding Connectors.
-
Product
5 Micron Wire Grid Polarizer
-
These wire grid polarizers are fabricated from 5 micron diameter tungsten wire, and have a choice of wire spacing down to 12.5 microns. They are suitable for use from approximately 50 microns (or 6 THz) to longer wavelengths. Please refer to the table below for the standard availability of wire spacing and frame clear aperture / outer diameter.
-
Product
Polarization Extinction Ratio Measurement
-
Rapid & Accurate measurement for PER, Angle, and Power. The most suitable light source for PER measurement.
-
Product
Polarization Controller and Scrambler - PXIe
Pol 1000 Series
Controller
The Pol 1000 Series PXIe module enables high-speed automated polarization control for polarization dependent testing procedures.Rotate or scramble the polarization of your signal with no need for manual adjustment of paddles or tension screws using intuitive software, LabVIEW or comprehensive SCPI commands. Pol 1000 Series can be used with our wide range of optical and electrical PXIe test modules, and can be used to build complete mixed-signal test platforms.
-
Product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
-
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
Product
Polarization Maintaining Band Pass Filter
-
Zhongke Rayzer Optical Technology Co.,Ltd
Selects the thin film filter withgood performance to ensure the high quality opticalperformance, stability and reliability. It is uses to shieldnoise signal in EDFA and fiber laser system. It has thecharacteristics of high isolation, low insertion loss, highreturn loss and high power.
-
Product
LXI 8:1 Optical MUX FC/APC Single Mode
60-850-011
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
1 Channel, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTA
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
Thermo-Electrically Cooled Dual Mode Analog/Photon Counting Photmultiplier Tube (PMT)
CoolOne
-
For spectroscopy and microscopy experiments in the UV/Vis/NIR region of the spectrum, a photomultiplier tube (PMT) is the ideal detector for quantitative low light level measurements. A PMT is extremely sensitive, with very wide dynamic range so it can also measure high levels of light. PMT’s are also very fast so rapid changes in optical signals can be reliably monitored. As a practical matter, PMT’s are durable, long-lived, and economical.
-
Product
Single Mode & Multimode Testing Kit
KI-TK076
-
Single mode & multimode testing kit with an optical power meter and light source for low to medium test volume on SM and MM systems.
-
Product
PXI Single 2 Channel (M Mode) SC 50 Cons
40-855-212-M50
Switch Module
Fiber Optic MEMS Switching cards available in many high density formats with a choice of five different connector styles to suit most applications
-
Product
Single Mode & Multimode Tester Kit
KI-TK038
-
Single mode & multimode tester kit for low to modest test volume on MM and SM systems.
-
Product
2 Channels, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTE
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
Polarisation Mode Field Diameter
MA500
-
MA500 is our polarisation mode field diameter (MFD) and effective area (Aeff) measurement system, specially designed to measure large effective area and high NA single mode fibers with its enhanced dynamic range and high-resolution scanning optics.
-
Product
PXI Single 2 x 2 Fibre Optic (M Mode)STM62.5
40-860-512-M62.5
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
High Temperature Charge Mode Accelerometers
-
Charge mode output accelerometers from PCB® use piezo-ceramic sensing elements that output an electrostatic charge signal proportional to the applied acceleration. These sensors can operate at extremely high temperatures because they do not contain the built-in signal conditioning electronics that limit the temperature range of ICP® accelerometers. Charge mode sensors are used in the testing of gas and steam turbines, jet engines, high power motors, exhaust systems and automobile engines where temperatures can range from 500° F (260° C) to 1200° F (649° C).
-
Product
RS422 Mode SI-module With Optical Isolation
MX422-G
-
RS422 mode SI-module with optical isolation
-
Product
LXI 16:1 Optical MUX SC/PC Single Mode
60-850-213
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
Wavelength Dispersive X-ray Fluorescence Spectroscopy
-
Wavelength Dispersive X-ray Fluorescence Spectroscopy
-
Product
Mini Fiber Optical Switch at Single Mode Latching 1310/1550nm 5V with LC/PC Connector
SUN-FSW-1x4
-
Guilin GLsun Science and Tech Group Co., LTD
GLsun 1*4 Optical Switch micaro optical switch informationFeatures•Low Insertion Loss•Wide Wavelength Range•Low Crosstalk•High Stability,High Reliability•Epoxy-free onOptical Path•Latching and Non-latchingApplications•F&D in Laboratory•System Monintoring•OADM•MAN(Metropolitan Area Network)•Network Security and MonitoringSpecificationsParametersUnitSUN-FSW-1×4Wavelength Rangenm850±40 / 1300±401260 ~ 1650Test Wavelengthnm850 / 13001310 / 1550Insertion Loss 1, 2dB≤1.0Return Loss 1, 2dBMM ≥ 30 SM ≥ 50Crosstalk 1dB≥ 55PDLdBSM ≤0.1WDLdB≤0.25RepeatabilitydB≤±0.02Operating VoltageV3.0 or 5.0Voltage Pluse Width(Latching)ms≥ 20DurabilityCycles≥ 10 MillionSwitching Timems≤8Optical PowermW≤500Operating Temperature℃0 ~ +70Storage Temperature℃-40 ~ +85Relative Humidity%5 ~ 95Dimensionmm(L)33.5×(W)25.5×(H)9.5 ±0.2Note: 1 Within operating temperature and SOP.2 Excluding connectors.GLSUN 1x4 fiber optic switch micaro optical switch
-
Product
Dispersive X-ray Fluorescence Spectrometer
SPECTRO MIDEX
-
SPECTRO Analytical Instruments GmbH
The SPECTRO MIDEX is known to be an all-round talent for the fast, non-destructive analysis of small spots and the rapid mapping of large surfaces (up 233x160 mm, 9.2x6.3’’) in research and development as well is in compliance screening applications as many elemental analysis tasks in industry, research and the sciences require a non-destructive measuring system that is extremely sensitive and offers a small measuring spot.
-
Product
Polarization Controller and Scrambler - MATRIQ
Controller
The Pol 1000 Series enables high-speed automated polarization control for polarization dependent testing procedures.Rotate or scramble the polarization of your signal with no need for manual adjustment of paddles or tension screws using intuitive software, LabVIEW or comprehensive SCPI commands.
-
Product
Single Mode Fiber Optic Rotary Joints
-
Single Mode Fiber Optic Rotary Joints (FORJ) can be supplied as a stand alone product. Its features can be customized : wavelength, connectors, characteristics of the fiber…
-
Product
Energy Dispersive X-ray Fluorescence (ED-XRF) Spectrometer
XEPOS
-
SPECTRO Analytical Instruments GmbH
The new SPECTRO XEPOS spectrometer represents a quantum leap in energy dispersive X-ray fluorescence technology. It provides breakthrough advances in multi-elemental analysis of major, minor, and trace element concentrations. New developments in excitation and detection deliver outstanding sensitivity and detection limits yielding remarkable gains in precision and accuracy. The amazing SPECTRO XEPOS excels at critical tasks from rapid screening analysis to precise product quality control. Apply it for at-line processing in a variety of industries, for geology and mining, for environmental and waste monitoring, and for research and academia.
-
Product
A Ready-to-use Solution To Orientate Polarization Maintaining Fibers Inside Connectors
PM ALIGNER-V2
-
PM Aligner-V2 is the simplest way to orientate precisely a PANDA Polarization Maintaining fiber inside a connector or ferrule. With a long working distance, PM Aligner-V2 allows the operator to work manually around the ferrule of the connector. After positionning, the curing phase becomes easy to realize without affecting on the PM fiber alignement.
-
Product
EBIRST Slave Mode Connection Cable
93-970-301
-
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
