-
Product
Memory Test System
T5835
-
The new T5835 has full testing functionality, from package testing to high-speed wafer testing, for any memory ICs with operating speeds up to 5.4 Gbps, including all next-generation memories from NAND flash devices to DDR-DRAM and LPDDR-DRAM. It can handle 768 devices simultaneously for final package-level testing. It additionally features functions such as an enhanced programmable power supply (PPS) for advanced mobile memories, and a real-time DQS vs. DQ function to improve yield.
-
Product
Battery Backup IC
-
Analog Devices offers a range of supervisory circuits that offer a complete single chip solution for power supply monitoring and battery control functions in microprocessor systems. Functions include microprocessor reset, backup battery switchover, watchdog timers, CMOS RAM write protection, and power failure warning.
-
Product
Universal Test System
LS6601A
-
LS6601A Universal Test System is based on LXI bus, primarily used for functional electronic product or system verification, test parameters. Because the system design is based on LXI bus structure, so its addition to general characteristics of versatility, scalability, but the architecture of the system more flexible, the test system is not limited to one or more cabinets, but may be needed test network and multiple LS6601A and can be easily grouped into one or more of the ground test system, depending on the test mechanism, form a powerful set of test, control, simulation, simulation, data management as one; distributed in different places .
-
Product
Function Test Systems
-
These specialist Automeg models test the function and integrity of wiring harnesses combined with active components such as relays, switches, contactors, diodes, LEDS, actuators and other active components.Our software takes the complex and traditionally long task of creating functional tests away from the test engineer and allows these to be created automatically, from existing ECAD data and our component library and automated software routines. All the different routes and subtests are automatically calculated in seconds.
-
Product
Discharge Test System
-
The automated testing equipment automatically performs charge and discharge of energy devices such as the rechargeable batteries(cells, modules, packs) that are installed in PHV/ EV and mobile devices, while measuring the voltage, current, temperature, and impedance.
-
Product
Optics Test Systems
IR Autocollimator
-
Optik Elektronik Gerätetechnik GmbH
The infrared autocollimator was specially designed for the 1550 nm wavelength range. In conjunction with the CROSDETECT evaluation software, it achieves a measuring accuracy of 1 arcsec with a resolution of 0.1 arcsec. The camera used is suitable for the wavelength range from 900 nm to 1700 nm.
-
Product
ICs For Factory Automation (R-IN)
-
The advancement of Industry 4.0 and the Industrial Internet of Things (IIoT) brings with it a growing need to boost factory productivity. The use of Ethernet-based networks in factories is becoming more widespread, as deterministic, safe communications across all levels of the factory are more critical than ever. Renesas has a comprehensive portfolio of products to support Industrial Ethernet solutions leading to increased factory productivity and reduced production cost.
-
Product
Camera Test System
FS 8681 / SR
-
FS8681/SR is software for evaluating images* and making pass/fail judgments in camera mass production inspections. It consists of the "Editor FS8681" application that sets the inspection content and the "Sequence Runner FS8681SR" application that executes the set inspection.
-
Product
Oil Test System
-
The Oil Test system Model OTS 2K1 is portable transformer oil Test system. It is a specially designed for accurate measurement of Loss Factor, Permitivity & Volume Resistivity Measurement of Transformer Oils & Petroleum jellys. The test frequency is 50 Hz . The system is provided with Mode Selector Switch so that once the oil cell is connected, it can measure all Three parameters in different modes without handling the test leads.
-
Product
AC Resonant Test System
-
Yangzhou Power Electric Co., Ltd
Testing of certain apparatus requires much high voltage or current that a straight AC test system is not sufficient. Thus resonant test reactor with a variable core is needed. The main advantage of such test systems is lower input power and larger output power. The resonant test system is designed to compensate capacitance in the testing circuit precisely by tuning inductance of the test system. AC resonant test system is used for factory testing of middle, high and ultra-high voltage cables, capacitors, generators, motors, power transformers and gas-insulated switchgears.
-
Product
Power-Switching Test System
High Voltage Switching Test System
-
The Accel-RF Power-Switching Test System is capable of measuring reliability under a variety of conditions for switching power applications up to 1kV (off) and 25A (on) at rates up to 1MHz switching frequency, dependent on voltage. By leveraging technology developed for the RF burn-in tray platform with new fast switching measurement techniques, this system can support testing of multiple devices under elevated temperature stimulus in a small physical area, and offers the flexibility to test both soft- and hard-switching applications. The Accel-RF Power-Switching System is the most flexible and accurate power switching platform available.
-
Product
Test Adapters / Aeroflex Test System
52xx / 5300
-
We develop and manufacture test adapters for your existing interface including documentation and test program
-
Product
Hydraulic Test Systems
-
Genuen specializes in hydraulic test stands, including component tests, pumps, motors, valves, actuators, fatigue, load frames, and burst testers. As an industry leader in custom test systems, we focus on hydraulic solutions that leverage off-the-shelf technologies for mechanical subsystems and components. Our hydraulic test equipment has been deployed in aerospace and defense, automotive, industrial, commercial, and many other industries.
-
Product
Test System
ETS788
-
The 55/110 MHz ETS788 system boasts the same small footprint and cool quiet CMOS architecture as our ETS780 but with the new high-performance precision components of our Griffin series. This powerful member of the HiLevel family takes advantage of all of the tried and true features that have served users so successfully to date. Learn why the ETS788 is the perfect cost-effective solution for higher performance in Design Verification, Production and Failure Analysis.
-
Product
Phase Noise Test System
PN9000 System
-
Noise eXtended Technologies S.A.S.
The PN9000 is a simple and fast Automatic Phase Noise Test System covering a very wide frequency range. Its modular architecture allows optimum configuration, multiple measurement techniques and future growth in a NIST tested instrument.
-
Product
EBIRST 200-pin LFH To 104-pin D-type Adapter
93-002-422
Test Adapter
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
Cable Test Vans and Systems
-
Precise cable fault location, testing of new and diagnostic testing of existing cable routes – the BAUR cable test vans are suitable for any operation. Fast and reliable. Exactly adapted to individual requirements and predefined vehicle systems.
-
Product
Stationary Drive Test System
ACTAS CF80
-
Stationary test system for sequential final factory tests and function tests on up to 8 drives. The drive test system is operated and controlled with the ACTAS operating software. The test position is selected using the multiplex method. The test system can reproduce drive control with the aid of a logic module. This makes it possible to test any drive even if there is no control unit.
-
Product
Electrodynamic Vibration Test Systems
CV-series
-
CV-series is suitable for transportation tests. The lateral support stiffness and maximum displacement of the CV-series are large enough to be accommodate vibration tests of the specimens with high center of gravity.
-
Product
Test Automation Systems
iTest
-
Our iTest family of test automation systems provide a full range of capabilities, allowing you to purchase just the right solution for your application without having to overbuy.
-
Product
Metering ICs
-
Smart metering Analog Front End (AFE) ICs offer high accuracy when measuring DC and AC energy down to extremely low currents typical of home appliances in standby mode.
-
Product
ICE 3000 Series
ICE3001
-
This subsystem is an agile filter for the SATCOM frequency band, capable of acting as either a receive or a transmit filter. It enables simultaneous operation of multiple transceivers in extreme cosite environments. The ICE3001 provides multiple poles of RF selectivity to reduce broadband noise, harmonics, and spurious signals for either receive or transmit applications. This filter is a highly integrated design incorporating complete Built-in-Test capability. The design has been qualified for military applications. A dual-mount tray is also available as an option for easy incorporation on your platform. Cost-effective modifications are available on the ICE3001.
-
Product
Timing & Digital Logic ICs
-
Renesas offers a selection of industry standard quartz- and RC-based timing/oscillator ICs along with real time clocks. Timing circuits provide clock pulsing and synchronization in digital systems as well as pulse modulation circuits.
-
Product
Handheld Test Systems
-
Lightweight and easy to use handheld test systems designed with a plug and play approach, ideal when operating on site or close quarters.
-
Product
Transportation Simulation Test System
KRD50 series
-
KRD50 series transportation simulation test system is to simulate the actual road conditions such as shocks and vibrations during the transportation of various items of a specific load, and to evaluate the effect of the actual working conditions on the loading, unloading, transportation, packaging, sealing or internal structure of the goods. In order to assess or confirm the products and packaging.
-
Product
Ionic Contamination Test System
Omegameter SMD 650
-
The SCS Omegameter SMD 650, the long-time industry standard for ionic testing utilizing “static test” methodology, is designed to perform cleanliness testing on printed circuits and assemblies. Identifies the presence of ionic contamination on bare and assembled printed circuit boards and other electronic components. Provides an accurate and repeatable method for determining cleanliness on site. Provides immediate process control results, eliminating the need for outside laboratory testing.
-
Product
Ferroelectric Test System
LCII
-
Precision LC II is an affordable Ferroelectric Tester for research labs. This system offers 5Khz at 9.9V and also comes in a built in 10V, 30V, 100V, and 200V option. This unit can also be expanded to 10kV for bulk ceramic testing. Vision Software is provided with the LCII Test System. Vision uniquely allows the user to construct complex or simple programs with any number of tests to characterize all aspects of the sample in one execution while keeping track of the measurement results and the history of the sample being tested. Tasks such as Hysteresis, I/V, C/V, PUND, Waveform, Magnetoelectrics, Piezoelectrics are just a few features to choose from.
-
Product
ICs For Wireless Charging System
-
The feature of power receiving and charge/discharge system IC RAA457100 is integrated all functions needed for a wireless chargeing, rectification, charging control for small Lithium-Ion battery and top level of power-efficiency DC-DC converter in a singl chip as 3.22mm x 2.77mm small package.
-
Product
Manual Test System for ICT & ISP with Integrated ABex and up to 426 Test Points
LEON Fixture
Test System
The LEONFixture is the ideal ICT and ISP solution for small and cost sensitive applications. This manually operated test system combines optimal ergonomics with high performance, durability and precision, ensuring your investment over the long term. The LEONFixture features a test system integrated in a manual base fixture. The system is designed to be used with an Ingun ATS MA13 insert which could be customized by a lot of fixture houses all over the world.As part of the LEON Family, LEONFixture is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
-
Product
Ultrasonic Fatigue Testing System
USF-2000A
-
The USF-2000A implements materials fatigue testing at 20 kHz. Consequently, it is possible to evaluate 109 to 1010 order fatigue strength, where it had been difficult to obtain data before. Also, data for 107 cycles can be obtained in about ten minutes.
