Positioning
Aligning test set with target geography.
-
product
300mA One-Channel Amplifiers
Piezo amplifiers/controllers are designed for high precision positioning of low-voltage piezo actuators. These amplifiers are tuned for extremely high output stability and extremely low signal noise at the output. A low amplifier signal-to-noise ratio is very important because it determines the total resolution of the actuator. The nearly unlimited resolution of piezo-electric actuators using these amplifiers results in ultra-precise movement.
-
product
Satellite Signal Level Meter
Super Buddy
Complete more installs faster and better using the Super Buddy satellite finder meter. Be "sure of your bird" with the positive ID feature or use the automatic scan to identify the unknown satellite. The Super Buddy's geo-sensitive "Field Guide" shows you just the birds visible to your install -- ALL of them, with their individual transponders. The Super Buddy even gives the elevation and azimuth for whichever satellite you select.
-
product
Scanning Electrochemical Microscope
VS-SECM (DC And AC)
The SECM integrates a positioning system, a bipotentiostat, and an ultramicroelectrode probe or tip. The positioning system moves the probe close to the surface of the sample, within the local imaging zone. The bipotentiostat can polarize the probe only (feedback mode) or the sample and the probe independently (generator-collector mode), while measuring the resulting current(s). The probe is specially designed to have a specific tapered polish (per the RG ratio) and active radius below 100 microns. The positioning system scans the probe and charts position with measured electrochemical parameters, creating a data map of local current.
-
product
Adapter / Carrier Converter Card
PCIBPC104pET
PCIBPC104pET adapter / carrier converter card provides the ability to install 1-4 active PC104p or PCI-104 cards into a standard PCI slot. PCIBPC104pET has a PC104p and PCI-104 compatible stack position mounted to a universal voltage shorter than 1/2 length PCI card. The PC104p position is stackable with all 4 active positions usable.
-
product
Rolling Seal 4 Optical Connector
RS4
- GAF/ELI enhances mating efficiency and eliminates potential for shell damage while offering positive latch indication.- Longer, contoured cable end lead-in bushing enhances fine alignment of connector halves during the mating sequence.- Reduced channel count to align with more efficient field architectures.
-
product
Photonics for Measuring Laser Output
Ray gt Photonic
raygt photonics for measuring laser output assist international research laboratories and laser technology manufacturers with precise positioning and output data.
-
product
CAN + OBD Network Data Converter
NC1
Get RPM, Speed, Absolute throttle position and many other vehicle parameters in real-time from your vehicle's standard OBD connector. Works with ANY OBD2 equipped vehicle. Works with ANY data acquisition equipment.
-
-
product
Programmable Selsyn Indicators
PSI
Computer Conversions Corporation
Computer Conversions Solid State Selsyn/Resolver Indicator digitizes the outputs of Selsyns, Synchros and Resolvers for position indication and control applications. The Selsyn Indicator is designed to replace failure prone mechanical selsyn torque receivers, counters, etc. The tracking converters high noise immunity and high speed tracking characteristics make it ideal for use in industrial envrionments.
-
product
Cable Assembly, Receiver, TriPaddle, 20", 6 and 2 Position Mini-Combicon Plugs
540162010101
Cable Assembly, Receiver, TriPaddle, 20", 6 and 2 Position Mini-Combicon Plugs
-
product
Precision Assemby & Production Solutions
Due to the continuing trend of product miniaturization with increased complexity, accurate gluing, welding, laser and assembly solutions are key for next-generation devices. As a result, the clear distinction between assembly and testing starts to blur. In smartphones, for example, testing and soldering the battery is one step in the production process. Hence, a combination of ultra-precise dosing, fixation, positioning and real-time feedback is essential to ensure best results and maximum reliability.
-
product
Mounting Panel, iCon, 6U, 6 Positions, with Slide Mounting (slide kit required)
310113635
The 6U Slide-Mounted Plate mounts to standard 19" racks and slides open to allow access to wiring between the instruments and VPC iCon receivers. The 6 cutouts are space evenly across the panel. iCon cover plate is sold separately (310113467). This mounting plate is designed to work with a slide kit and includes flanges and an instrument bracket. A slide kit is required for use.
-
product
Safety Laser Scanner Type 3
SD3-A1
Panasonic Industrial Devices Sales Company of America
The Panasonic SD3 Safety Laser Scanner is a cost-effective alternative for guarding danger zones. It can be used flexibly in confined spaces and for areas where the danger zone changes.The SD3 can monitor an area within an angle of up to 190° and divides it into 2 zones: a warning zone within a radius of 15m, and a protection zone within a radius of 4m. The contours of these zones can be configured precisely for any application. Up to eight zone patterns can be set and activated at any given time even during operation.The reference boundary function memorizes the position of stationary objects and establishes a virtual boundary. It also monitors beam alignment after installation and issues an alarm if a beam becomes misaligned.
-
product
Scanning Electrochemical Systems
The VersaSCAN is a single platform capable of providing spatial resolution to both electrochemical and materials-based measurements. Each VersaSCAN is based on a common high-resolution, long-travel, closed-loop positioning system mounted to a vibration-resistant optical base. Different auxiliary pieces are mounted to the positioning system. These ancillary pieces (e.g., an electrometer, piezo vibration unit, or a laser sensor) provide functionality to the positioning system for different scanning probe experiments. VersaSTAT potentiostats and Signal Recovery Lock-in Amplifiers are integrated via ethernet control to make accurate measurements of these small signals.
-
product
Cut Susceptibility Tester
King Design Industrial Co., Ltd.
Equipment conforms to IEC61730 MST12 specification. Pre- or post-round can be selected for control wiring connection. With weights block’s positioning pin is removed before test; and is inserted in the rear positioning hole for the remaining time. Equipped with rings at both front and rear end; used to connect a rope and control the driving direction. Use replaceable special cutting chip.
-
-
product
Handheld OTDR
JW3302B
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3302B handheld OTDR is a new generation of intelligent optical measuring instrument designed for the optical fiber communication system testing by JOINWIT.This product is mainly used to measure the parameters of optical fibers and cables, such as length, loss, and connection quality, etc.; it can realize the accurate positioning of event points and fault points, and can be widely used in the construction, maintenance testing and emergency repair of the optical fiber communication systems as well as the research, production and production measurement of optical fibers and cables and so on. This product can provide you with the highest performance of solutions for installation and construction of fiber optic network construction and the subsequent fast and efficient maintenance and troubleshooting testing.
-
product
PXI Switch - 4x8 2-Wire Matrix Module
PXI-7931
ADLINK PXI-7931 is a matrix module with 32 cross-point 2-wire relays (DPDT, 2 Form C). The default configuration of the PXI-7931 itself is a 4-group 2x4 2-wire matrix. With the termination board, TB-6231, users could flexibly choose one of the configurations: one 4x8, two 4x4, one 2x16, two 2x8 and four 2x4. Any contact of the PXI-7931 can connect to other contacts, individually or in combination. The PXI-7931 matrix module simplifies the wiring and makes it easy to change the internal connection path. The contact position of the relays can be changed either by direct software commands or by following the instructions previously stored in the on-board scan list. The scan list advances upon the trigger from external measurement devices, such as a DMM. The scan list could also advance when the scan-delay timer expires. In the PXI-7931, PXI trigger functions are supported and software programmable. Multiple modules can therefore be synchronized without additional field wiring.
-
product
Signal, Module Insert, Receiver, i2 MX, TriPaddle,33 Position
510143006
Signal, Module Insert, Receiver, i2 MX, TriPaddle,33 Position.
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196C
The 16196C surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
0.10° Accuracy Full Attitude Dynamic Motion Sensor
DMS-10
The DMS range of motion sensors is designed specifically for the motion measurement needs of the marine industry. Whether it is achieving IHO standard survey from any size of vessel, or providing safety critical monitoring of offshore platforms, large vessels, helicopter landing decks, cranes and positioning systems, the DMS provides accurate motion measurement in all sea conditions. Incorporating an enhanced external velocity and heading aiding algorithm for improved accuracy during dynamic manoeuvres, the solid state angular rate sensors offer reliability in the highest performing vertical reference units ever produced by TSS.
-
product
Receiver, S6, 6 Module, With 20" Platform, For Slide Mount (slide Kit Required)
310122108
The S6 Mass Interconnect Receiver is designed to mount to slides in a rack application or directly to a tabletop. It features positive-latching mechanisms and integrated guide pins to create a highly reliable engagement system. The S6 Receiver is very versatile and has module positions screened on top for ease of module placement.
-
product
Process Control Actuators
SM-1700/SM-5000
The SM-1700/5000 Series of rotary actuators are internally geared to produce up to 12,500 ft.lbs. (16,950 Nm) of torque, and offer continuous modulation. They are ideally suited for dampers, vanes, valves and other process control applications requiring exact positioning control.
-
product
C Series Counter Input Module
The C Series Counter Input Module features flexible, 32-bit counters. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal, switchable pull-up resistor. Additionally, you can use the C Series Counter Input Module to perform encoder position and velocity measurements as well as to synchronize the counters with other analog, digital, and counter measurements in your chassis.The C Series Counter Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Pan & Tilt Push Cameras
Advanced Inspection Technologies Inc.
Pan & Tilt Push Cameras Inspection System are the first true high definition push rod camera system with a remotely controlled pan & tilt camera. A brilliant 7" touchscreen LCD allows you to remotely control camera direction, focus add text annotation, view camera position and level. Super portable and operates on AC or DC power (4 hour rechargeable Li-ion battery).
-
product
Fast LID Measurements for EOL
KMP
TechnoTeam Bildverarbeitung GmbH
The KMP is the solution to cost-effectively bring indirect light measurement technology to places with too little space for a BV room. Its lightweight and compact design allow it to be integrated into production lines, positioned next to production or in a small lighting lab.
-
product
WinSRS Software
The GHI Windows version of our powerful SRS module has been made even more powerful by the addition of new processing modes. These include: 1. Statistical SRS - This mode provides MEAN and Positive STANDARD DEVIATION plots which can be used when tailoring shock specifications based on environmental measurements. 2. Max-I-Max Envelope SRS - This module plots succeeding SRS's on one screen while at the same time plotting an 'envelope' that bounds all SRS's processed. 3. Overlay Plot - This mode allows overlaying plots of multiple SRS's. The user may plot Positive and Negative Max-I-Max spectra on the same screen. The foregoing are in addition to our traditional features
-
product
Micro Power Insert, Receiver, SIM, 2 Position, 2 Slot
510180102
This insert contains 2 micropower contacts and is part of the Infinity Connector system. It is used in the 90 Series SIM Module and occupies 2 of the 34 slots in this module. This insert comes loaded with contacts. Individual contacts sold separately p/n 610142106.
-
product
50 mA to 300 mA dDrive Digital System
The d-Drive® modular piezo controller system from piezosystem jena combines the highest positioning accuracy with a personalized design. A complete system contains an EDS interface (with display and controls), paired with a variety of EVD digital amplifiers, all contained in a 19-inch rack-case.
-
product
0.50° Accuracy Full Attitude Surface Dynamic Motion Sensor
DMS-550
The DMS range of motion sensors is designed specifically for the motion measurement needs of the marine industry. Whether it is achieving IHO standard survey from any size of vessel, or providing safety critical monitoring of offshore platforms, large vessels, helicopter landing decks, cranes and positioning systems, the DMS provides accurate motion measurement in all sea conditions. Incorporating an enhanced external velocity and heading aiding algorithm for improved accuracy during dynamic manoeuvres, the solid state angular rate sensors offer reliability in the highest performing vertical reference units ever produced by TSS.
