Depot Level Test
faults diagnosis down to nth degree for repair analysis and recovery.
See Also: System Level Test, Level, SRU
-
Product
Digital Sound Level Meter
Model KM 926
-
Kusam Electrical Industries Limited
• KM 926 designed according to the IEC 651 TYPE 2 & ANSIS1.4 TYPE 2 for sound level meter.• Instantaneous sound measure function.• Measurement Range : 30 ~ 130decibel• With two equivalent weighed sound pressure levels, A & C.• Fast & Slow dynamic characteristic modes.• AC & DC signed output for frequency analyzer level recorder, FFT analyzer, graphic recorder etc.
-
Product
Level Control Loop Trainer Model
ULP-24P & ULP-24C
-
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Level Control Setup comprises of acrylic measuring tank fitted with Level transmitter, control valve, I to P converter, source tank with water pump and necessary flexible piping for water circulation. The system is mounted on a table top powder coated metal frame. Level transmitter is of capacitance or DPT type sensor. The electronic panel comprises of ADC and DAC card with RS-232 interfaces.
-
Product
Sound Level Meter & Real-time Analyzer
824
-
The Larson Davis System 824 combines advanced sound level meter and real-time analyzer capabilities into a rugged, user-friendly, ergonomic package. The base unit is an Integrating Sound Level Meter (ISM) that meets Type 1 Standards and offers simultaneous measurement of sound pressure levels using fast, slow, and impulse detectors, for A, C, and flat frequency weightings. This feature, termed ANY LEVEL™ measures 48 sound pressure parameters at once with a linear, 105 dB range. With firmware enhancements, the base unit expands as needed to accommodate multiple data processing requirements
-
Product
Thermal Dispersion Level Switches
-
ABB's Thermal Dispersion products can be used for flow, level or temperature detection. One switch can be field configured to detect one of these three process conditions.
-
Product
Shield Level / Pathloss Equipment
SG1000B/PR1000A
-
The SG1000 Signal Generator and PR1000A Preamplifier have been designed to simplify the measurement of shielding integrity in a shielded enclosure. When coupled with a high stability spectrum analyzer and an appropriate selection of test antennas, the SG1000/PR1000A combination can measure shielding effectiveness at all of the NSA 94-106 (supersedes NSA 65-6) defined test frequencies from 1 kHz to 10 GHz.The PR1000A amplifies the received signal from the test antenna and overcomes the high noise figure of the companion test receiver or spectrum analyzer. The PR1000A will ensure that the system noise figure will be less than 4.5 dB at all test frequencies from 1 kHz to 10 GHz. When used with a spectrum analyzer measurement bandwidth of 100 Hz, the system exhibits a sensitivity of -150 dBm at the test antenna output.To overcome high cable loss between the test antenna and the PR1000A assembly at 10 GHz, a remote low noise pre-amplifier (Praxsym PN 310-010091-001) is mounted directly onto the 10 GHz antenna.
-
Product
Trace Level Chemiluminescence NO-NOy Analyzer
Model T200U NOY
-
Teledyne Advanced Pollution Instrumentation
The Model T200U NOy analyzer has been developed and refined specifically to address the challenges of NOy monitoring as required, for example, in the US NCore network. It uses the proven chemiluminescence principle and is coupled with a remote NOy converter via umbilical to allow measurements with a lower detectable limit of 50 ppt.The Model T200U NOy analyzer combines a gold plated reaction cell with an enhanced performance pump, special low noise photomultiplier tube, and unique signal conditioning to provide exceptional sensitivity. In addition, a pre-reactor separates the NO-O3 reaction from background chemiluminescence to allow accurate auto-zero of the analyzer. The remote NOy converter is provided with a stainless steel, NEMA 4X (IP65) enclosure and custom sample umbilical to allow a mounting height of 10 meters. In addition, the converter features a unique purge circuit designed to remove residual calibration gas.
-
Product
Test Fixture Kits
Test Fixture
More then ten years of experience in special, customized engineering and manufacturing brought us to the highest level of creating reliable, flexible and robust Test Fixtures. Currently our HQ is located in Vecsés, Hungary together with our R&D. Equip Group has Test Fixture Kit manufacturing plant in Serbia, focusing on supplying competitive, high – quality and high – volume products for the global market.With more then 180 employees, Equip – Test is able to offer our customers turnkey solutions in fixturing with test program generation. No matter if you have a simple or complex, high-density PCB (Printed Circuit Boards), or if you have DUT (Device Under Test) already assembled into metal or plastic housing, we can offer you a very stable technical solution.
-
Product
Level Controllers
-
Measure and control fluid levels in a contained area or facilitate automatic filling and emptying operations with Omega's dependable single and multi-sensor level controllers.
-
Product
Ceramic Capacitor Input Water Level Gauge
HR8008
-
HighReach Measuring & Controlling System Co.,Ltd
HR8008 is a high-precision pressure water level gauge that monitors surface water or groundwater level and water temperature for a long time. It uses ceramic pressure sensitive components with good stability, high precision and strong overload capability. It adopts advanced mixed signal processing technology. Full-scale digital linear correction can be realized, digital temperature error compensation in full temperature zone; compensation parameters are stored in non-volatile memory, multiple safety protection mechanisms are avoided, and products cannot be used due to loss of calibration parameters; Monitoring function effectively preventing accidents such as crashes and program runs, and greatly improves the reliability of the product.
-
Product
Datalogging Digital Sound Level Meter with RS-232 Software and Cable
735
-
Whether you are testing for OSHA compliance, quieting equipment, or monitoring the roar of a stadium crowd, B&K Precision's Sound Level Meters can get the job done. The model 735 Sound Level Meter provides 30~130 dB capability in three convenient measurement ranges Low, Med and Hi with an accuracy of ±1.5 dB. The meter meets the IEC 651 Type II and includes frequency weighting A & C and fast and slow time weighting.
-
Product
Three-Phase Testing
CMC 310
-
The CMC 310 is specifically designed for basic three-phase testing of protection and measurement devices. It is operated by the CMControl P software which runs on the CMControl P unit, a Windows PC or on an Android tablet. Its intuitive user interface and the test tools included are optimized for quick manual testing in the field.
-
Product
Test Solution
Novus, Novus-M, & Novus-R 100/25GE Load Modules
-
Keysight Network Applications and Security
Novus, Novus-M, and Novus-R are Ixia’s next-generation architecture and test solutions that satisfy the test needs of both high-density, multi-rate switch/router makers and the organizations implementing the network equipment. Supporting eight native QSFP28 100GE ports and up to 32-ports for 25GE per load module, Novus load modules enable interoperability and functional testing, as well as high-port count performance testing.
-
Product
Luminaire Testing
-
Product Safety Consulting Inc.
With the emergence of LED technologies, being part of the renewed energy scene requires knowledge of how to design products to meet consumer needs while passing even more stringent safety testing than ever before. Staying on top of the new testing requirements, from local and global standpoints, is what we do. Standards generally are not clear; they leave room for interpretation and often present constraints to product design. At PSC, we offer solutions to non-compliance rather than simply reporting a pass/no-pass statement. And, we communicate with straightforward explanations of safety issues that often arise during the testing process. Our expert product testing team understands what you need to do to achieve compliance. Failing at the testing stage only costs you valuable time and money. It allows the competition to beat you to the sale and takes resources away from future growth.
-
Product
Battery Powered, Stand Alone Water Level and Temperature Data Logger
Level1000
-
The Level1000 is a rugged, submersible, battery powered, stand alone, water level and temperature data logger. Its stainless steel enclosure makes it perfect for use in lakes and streams. This is an all-in-one compact, portable, easy to use device that will measure and record data for up to 16,383 measurements.
-
Product
Basic Sound Level Measurement System
-
The system utilizes a National Instruments CompactDAQ data acquisition device and the Nelson Acoustics Trident software application to provide a basic, computer based, sound pressure level measurement system.
-
Product
Temperature Test
-
Function and safety under extreme conditions. In the field of environmental simulation, ENGMATEC offers a wide range of efficient systems for quality assurance, development and production.
-
-
Product
Test Software
ATI
-
The ATI Test System Software and its utilities are built on a core of mature, object-oriented software components that have been thoroughly field tested and refined over many years. All of ATI's systems share a common core functionality and an easy to use program interface. Our highly skilled software and engineering experts are able to integrate nearly any OEM test or embedded systems equipment into the test system's design whether it's standard or proprietary.
-
Product
Test Benches
-
Atec has made test equipment throughout all of its 65-year history. Test benches for aerospace and energy uses represent a significant segment of our experience. Atec has produced test benches involving hydraulics, mechanicals, electromechanicals, electronics, pneumatics, motors, and digital automation. Atec test benches have performed for challenging measurements, factory production, problem analysis and component overhaul scenarios. Today, complex test benches have capable data acquisition, control and communication systems integral in their electronics. Atec’s ADAQ™ system, based on COTS components and software, is proven and popular in test bench applications. DCUs, ECUs, FADECs and earlier analog or mechanical control units are easily interfaced.
-
Product
Test Kit
METRISO 3000
-
Wolfgang Warmbier GmbH & Co. KG
Suitable for resistance point-to-point and resistance to ground measurementsIntegrated data logger with USB communication port for data transmission (50.000 test values). The supplied Report Generating Software ETC allows to generate a complete test reportHumidity and temperature sensorA barcode scanner can be used in order to record measurement points before testing
-
Product
Corosion Testing
-
Materials Evaluation and Engineering
Electrochemical corrosion experiments can provide a variety of data related to the pitting, crevice corrosion, and passivation behavior for specific sample/solution combinations. These data are useful in selecting materials and/or determining how manufacturing processes affect corrosion properties.
-
-
Product
Vision Testing
-
Visual evaluation is a critical step in achieving accurate color, and ensuring accurate color vision is a must. Farnsworth-Munsell Hue Test solutions allow you to evaluate the color vision of your team.
-
Product
In-Circuit Testing
-
If you are looking for in-circuit test applications, equipment or advice, our experienced engineers can help you. Whatever your fixturing requirements or special software features, our long history of work in this field means that we have probably seen and done it before.
-
Product
Magnet Testing
Helmholtz Coils
-
A coil arrangement consisting of two coils with the same radius or edge length is called a Helmholtz coil. At the correct distance, these coils are arranged in parallel on the same axis and current flows through them in the same direction. Their magnetic field is then characterized by a large homogeneous area in the center of the coil, which is freely accessible for experiments and measurement tasks. Helmholtz coils can have a circular or square geometric shape.
-
-
Product
Load Tests
-
For the production and quality assurance of electric motors and electric drive systems, the use of flexible and customer-specific testing technology is required. Vogelsang & Benning supplies the same to the needs and the application of the customer.
-
Product
System Test
-
Testing a complete system is very different from unit and integration test. It starts with the V model that defines the system requirements, and this needs an effective system test capability that includes both the system and the environment around it. If the system has interfaces to the outside world, communications links or human control, these interfaces have to be tested.
-
Product
Test Sockets
-
Yamaichi Electronics Co., Ltd.
A test socket is the ideal point to test your home’s internal phone wiring for faults. You can also use it to identify any potential faults with the phone line outside. Your test socket is located in your master socket. It is the point between the internal phone wiring in your house and the phone line outside. That means by plugging into your test socket you can bypass all the internal wiring and test your device directly on the phone line.
-
Product
Interoperability Testing
-
Underwriters Laboratories Inc.
Leverage our expertise to validate that your product not only works as expected with all other relevant devices but also conforms to all appropriate standards and technology platforms. We do this by testing products in real-world scenarios. We are an approved testing laboratory for many IoT and wireless standards bodies, such as Bluetooth SIG, Thread Group, Wireless and Zigbee Alliance, and are actively engaged with key players in 5G. We test interoperability across many industries including appliances, building systems, consumer electronics and vehicles.
