Loop Indicators
See Also: Indicators, Angle Position Indicators, Fault Indicators, Voltage Indicators
-
Product
Angle Indicators
-
Computer Conversions Corporation
This series of units were designed to satisfy Hi speed multiturn synchro/resolver applications where the output data must be fresh and no data staleness can be tolerated. The tranducers utilized are the same as in the regular MDS series, however different tracking electronics are used. The resultant data tracks the input shaft perfectly and is always fresh and accurate at input speeds up to 64 revolutions per second, depending on the resolution. Data in BCD or Binary formats are available, and clean, unambiguous crossovers are guaranteed.
-
Product
Phase Sequence Indicator
8PK-ST850
-
Two functions in one unit incluidng open phase and phase sequence. Large size alligator clips : able to clip on switch-board terminals easily. Identify 3 phase sequence and open phase check Ideal for installing conveyor lines, pump systems and interconnected drivers. No exposed metal parts. Safety features are incorporated throughout, including the pushbutton switch designed to minimize damage due to negligence. Safety approval: CE marks, IEN 1010 CAT. II.
-
Product
Short Circuit Loop Impedance Meter
AMZC-304
-
Short circuit loop impedance measurement in networks with nominal voltage: 220/380V, 230/400V, 240/415V, with frequency 45…65Hz ; Short circuit loop impedance measurement with 15mA current, without triggering RCD. ; Detection of the replacement L and N in the socket and automatic swap in the meter
-
Product
PXI Analog Output/Current Loop Simulator Module - 8 Channel
41-765-003
Analog Output Module
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Water Level Indicator With Alarm Acknowledgement
IM1731
-
We offer Water Level Indicator with Alarm Acknowledgement to our clients.
-
Product
Phase Rotation Indicator
9040
-
The Fluke 9040 is effective for measuring phase rotation in all areas where three phase supplies are used to feed motors, drives and electrical systems. The Fluke 9040 is a rotary field indicator and can provide clear indication of the 3 phase via an LCD display and the phase rotation direction to determine correct connections.
-
Product
Outside Micrometer Equipped with Dial Indicator
-
Allows measurement with an indicator. Optimal for continuous measurement of mass-production parts.
-
Product
Phase Sequence Indicator
PHS 863
-
Two Functions in one unit including open phase and phase sequence. Large Size alligator clips can easily clip on switch-board terminal. Highly Reliable : Identifies 3 phase sequence and open phase check. Functional design : This model is ideal for installing conveyor lines, pump systems and interconnected drivers. Safety approval : CE marks EN 6101-1 CAT. III. EN 61010-2-031
-
Product
Phase Rotation Indicator DX2
-
STB Electrical Test Equipment, Inc
From the company who builds the popular analog ground fault detector comes the newest phase rotation indicator on the market. No other manufacturer offers a phase rotation indicator like STB's DX2 that will read up to 5kV! The phase rotation indicator is used to determine the phase sequence of three-phase voltages. This meter is most commonly used for phasing-in a power line which has supplied power to motors and plants. It is essential for testing departments of public utility systems for laboratory and field testing. The convenient and durable carrying case allows user to safely transport the unit to wherever the job takes them.
-
Product
Load Cell Indicator
-
Morehouse Instrument Company Inc.
This indicator can read mV/V and use free, custom Morehouse software to convert the mV/V units to engineering units with coefficient files from ASTM E74 or ISO 376 reports. This meter is often the choice for accredited calibration service providers that want high accuracy and convenience but do not want to break the bank.
-
Product
Self Testing Clamps with Visual Indication
Bond-Rite REMOTE
-
As an alternative to the standard Bond-Rite, a ?remote? version is also available. In this configuration, the Intrinsically Safe monitoring electronics, flashing green LED and battery power supply are housed inside a tough, corrosion resistant stainless steel enclosure, designed for wall mounting. An insulated stowage point, for the safe return of the clamp when not in use, is included.
-
Product
Indicators
-
A device providing specific information on the state or condition of something, in particular.
-
Product
Economic Type Temperature Indicator
CS1-T
-
CS1-T economic type Temperature Indicator has been designed with high accuracy measurement, display and communication of Thermocouple or Pt100Ω.They are also available 1 option of 1 Relay outputs, 1 Analogue output or 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of machinery and testing equipments applications.
-
Product
Indicators - Test
-
Measures the deflection of the arm, the probe does not retract but swings in an arc around its hinge point.
-
Product
Multi-Standard Local Loop Simulatorw/Optional AWGN Generator
458-LM-A1-30
-
FEATURES: Simulates 26 AWG PIC as specified in ANSI T1.417; Bandwidth DC to 30 MHz; Solution for ADSL, ADSL2, ADSL2+, & VDSL2 chip/modem/DSLAM testing;
-
Product
Intelligent Transmitter with Digital Indication
LEO 3
-
KELLER AG für Druckmesstechnik
LEO 3 is a micro-processor based transmitter with digital double-display for pressure (top display) and for the output signal (bottom display). The display is powered from the 4...20 mA current loop. Functions:
-
Product
Array Solutions K9AY Loop Wire/Mast Kit
AS-AYL-4 WM
-
All materials required for the installation of your receiving loop system, have been included in this kit with the exception of those items listed below under the heading; ‘You will also need. ‘ The specified 8’ x 5/8” copper-clad steel ground rod can be purchased at just about any local hardware store or home center.
-
Product
Micro-Ohmmeter and Loop Resistance Tester
LRT 6000
-
LRT 6000: The right solution for impedance resistance measurement in compliance with all aircraft specifications on plane, helicopter, rocket, army vehicles for both production andmaintenance. It is a very easy-to-use and versatile instrument. Its ergonomics allow the user to use it either placed on the ground or across one's shoulder or chest. Awide back-lit LCDdisplay combinedwith an intuitive keyboard ensures simple and easy operation.
-
Product
Single Loop Controller
3200
-
The instrument has the largest red or green digital display in a 1/32 DIN package. In addition to the red or green display the 3200 benefits from three additional multi-colour LEDs to indicate process, alarm and configuration statuses.
-
Product
Opto-Isolated Current Loop Signal
4029
-
SPECTEC Innovative Sensor Solutions
SPECTEC's Model 4029 digital opto-isolated current loop signal conditioner prevents ground loops and interrupts any galvanic signals riding on magnetic speed sensor's output signal.. This signal conditioner converts magnetic, variable reluctance and inductive sensors' sinusoidal signals into a 4-20 mA output suitable for interfacing with process control units, dataloggers, flow controllers, and computers.
-
Product
Current Loop Adapter
OP-1C
-
This adapter supports current loop communications.The kit incorporates a communications circuit with photo-coupler isolation and constant-current power supply of insulated type, thus realizing not only monitoring but also easy communications testing with passive or active current loop devices.
-
Product
Frequency, Rate Meter, Flow Rate Indicator
-
Two independent scalable pulse-input channels from 0 Hz to 1 MHz. Channels may be combined arithmetically. One channel can display total while other displays rate. High read rate for control applications: AC line frequency can be measured to 50.0000 or 60.0000 Hz in a few line cycles. Ideal for use as a tachometer or readout of a turbine flow meter.
-
Product
Loop Tack Tester
-
Loop Tack Tester is applicable to measure the tack property of adhesive tapes, pressure-sensitive adhesives (PSA), and adhesive materials according to ASTM D6195.
-
Product
Model QLS 4-20 mA Loop Splitter / Retransmitter
-
Generates up to four individually grounded and individually adjustable 4-20 mA loops from a single 4-20 mA or 0-10V input. Overcomes problems which occur when the same 4-20 mA signal is applied to multiple loads in series. Allows outputs to have different grounds, and allows individual loops to be opened without affecting signal to other loads.
-
Product
Process Indicators & Field Devices
-
Field devices from the Field Analog series record and convert signals from resistance temperature detectors, thermocouples, resistance-type sensors, and voltage sensors directly on site.
-
Product
Loop A Line Products
-
Cable pair tracing and a lot more, Loop-a-Line products can remotely control a far end device (the oscillator) for up to 20km of cable. Using a Loop-a-Line allows the linesman to remotely change the state of the oscillator to any of five different states. Therefore eliminating the need for multiple journeys along the cable path.
-
Product
Lipo Battery Power Level Tester & Alarm to Indicate Low Power
#52023
-
Can be used for 7.4V (2S pack)and 11.1V (3S pack).Red LED will flash when cell is below 3.3V and an Alarm will sound when cell is below 3.0V indicating the Lipo Battery pack should be recharged.
-
Product
Flow Indicator
Qualitrol 092
-
Designed to indicate “pump on” and “pump off” conditions within a forced cooling system. Select models also indicate flow direction. Up to two SPST or SPDT switches are available for control and/or alarm functions. Large dial face provides easy viewing and is magnetically coupled to the flange assembly allowing leak free replacement if damaged.
-
Product
Test Voltage Indicators
PRV240FS
-
Verify your test tool works without unnecessary exposure to shock and arc flash. Make the process easy by using the PRV240FS Proving unit. Verifying that your T6 electrical tester is working properly reduces the need for personal protective equipment (PPE) when a known voltage source is not available for verification before tests are performed.
-
Product
Current Loop Supply Isolating Transmitter
Model TWS / TWS 2
-
Kusam Electrical Industries Limited
• Aux. Power AC 85 ~ 265V or DC 85 ~ 300V• High Accuracy 0.1% RO at 23 °C ± 5 °C• Output User Selectable• PC Plastic Case, DIN Rail or Wall Mounting• High Dielectric Strength (AC 1.5KV/Min, between Input / Output / Power)
