-
Product
Glycerine Refractometer, Freeze Point °C
PA202X-016-019
-
Celsius model – Glycerine measurement is fast and easy with the MISCO Palm Abbe digital refractometer. This refractometer has two scales, one for glycerine freeze point in degrees Celsius and one for glycerine concentration in percent by volume.
-
Product
PCI 8 Form C Relay Output / 8 Isolated Input Digital Interface
8011
-
The 8011 digital I/O interface provides 8 optically isolated inputs and 8 Form C relay outputs. The inputs protect the PC and other sensitive equipment from spikes and ground loop current that can be generated in industrial environments, while the outputs provide higher current capabilities (up to 2A) and are optimized for 24V operation.
-
Product
Carrier Card
VIPC627-ET
-
VIPC627-ET is a 6U VME carrier card with four IP slots and extended temperature range. Two 50-pin, 0.1 inch flat ribbon cable connectors mounted in the front panel provide access to all IP I/O lines. Also, all I/O lines of 'IP D' are routed to VME P2 and 14 user selectable I/O lines of 'IP C' can be routed to VME P2 via a jumper field.
-
Product
Diving Technology Test Systems
-
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
The imaging ultrasonic testing systems of the USPC 30XX series are optimized for testing a wide variety of materials and provide high-resolution findings in the form of A, B, C, D and F images. The hardware consists of an industrial PC, in which a motor controller and an ADC card are installed, as well as a HILL-SCAN pulser/receiver unit. An overview of the available systems is given in Table 1.
-
Product
200KHz DIGITAL LCR METER
VE2836U
-
200KHz Digital LCR Meter that can test Inductance (L), Capacitance (C), AC Resistance, Q, D, ESR and Tan. Comes with Bin Selection option.Test Frequency : 50Hz ~ 200KHzTest Signal Voltage : 100mV , 300mV , 1000mV , 2000mV
-
Product
LCR Meters
-
GAOTek LCR meters are devices designed to measure the inductance (L), capacitance (C) and, resistance (R) of an electronic component. The LCR meters are measured in term of impedance but it can be converted through the instrument’s circuitry so the meter reads L, C and R directly with no human calculation required.
-
Product
sbRIO-9375, Non-Enclosed, 24 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781212-01
Digital Module
Non-Enclosed, 24 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The sbRIO‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The sbRIO‑9375 offers isolation between the input and output banks from channel‑to‑earth ground. Non-enclosed modules are designed for OEM applications.
-
Product
Silicon O/C Content Tester
HS-OCT-6700
-
The HS-OCT-6700 system used to measure the O&C in silicon ingot and wafers. The system is the highest performance FT-IR systems available. While the spectrometer has the power to handle the most advanced research-level experiments, routine analyses are performed just as conveniently. Every facet of the Nicolet FT-IR spectrometer has been engineered to facilitate sample handling, introduce options to scientists, and increase laboratory throughput.
-
Product
48 Channel Relay Output Module
DP-VME-4059
-
DP-VME-4059 is a rugged module with 48 channel relay output, constructed using 2 Form 'C' Double Pole Double Throw (DPDT) relays. The relay channel operation is controlled through the VME bus. Internal read-back is provided to confirm the selected commands. The pole, Normally Closed (NC) and Normally Opened (NO) contacts are terminated at a pair of front panel 96-pin EURO male connectors.
-
Product
TG/DTA Simultaneous Measuring Instrument
DTG-60 Series
-
This instrument varies the sample temperature in accordancewith a program, and simultaneously measures the change inmass of the sample (TG) and the temperature differencebetween the sample and a standard substance (DTA). An analytical balance mechanism (Roberval mechanism) offers high reproducibility and allows worry-free operation even for measuring sample weights. Two models are available for different maximum measurement temperature requirements-the DTG-60 (max. 1,100 °C) and the DTG-60H (max. 1,500 °C). Corresponding DTG-60A and DTG-60AH models with a built-in autosampler are also available for measuring up to 24 samples automatically.
-
Product
2/4-CH PCI Express® GigE Vision PoE+ Frame Grabbers
PCIe-GIE7x Series
Frame Grabber
- Hardware Trigger over Ethernet with Action Command- Up to 120W PoE power from PCIe bus/4-pin/6-pin Molex connector- PCI Express® x4 compliant- IEEE 802.3at for PoE+ (Power over Ethernet Plus)- PoE protection and automated power budget control for enhanced asset protection- Easy-to-use utility and API provided for PoE power management- Multiple cards, multiple cameras, in a single system- Wide operating temperature range from 0°C to +70°C supporting non-drop frame capture in extreme environments
-
Product
Standard 1.71 (48.00) - 3.00 (85.00) General Purpose Probe
HPA-74T75
General Purpose Probe
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Test Center Remark: max. test center 187 mil / 4,74 mmFull Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 75Recommended Travel (mm): 1.91Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 598Overall Length (mm): 15.19Overall Length Remark: Tip “A-B”: 598 (mil), 15.19 (mil), Tip “C”: 586 (mil), 14.88 (mil), Tip “E, T135, T156, T65, T80”: 610 (mil), 15.49 (mil), Tip “T75”: 620 (mil), 15.75 (mil)
-
Product
14th Gen Intel® Core™ Ultra 7/5-Based Advanced Embedded Box PC
EMP-520 Series
Box PC
- 14th Gen. Intel® Core™ Ultra 7/5 Processors (Meteor Lake-H/U)- DDR5-5600MHz up to 96GB (48GB per DIMM)- 4x independent displays support EDID Emulation- 2x 2.5GbE, 1x COM, 6x USB ports, Type C Thunderbolt (optional)- 2 x Wi-Fi/BT/LTE antenna holes- M.2 2280 (SSD), M.2 3042 (LTE), M.2 2230 (Wi-Fi/BT)- VESA mount (optional)
-
Product
Sound Level Meters
LA-4441A|LA-1411/1441A
-
Three models of sound level meter LA-1411/1441A(Class 2) and LA-4441A (Class 1) are applicable to IEC 61672-1:2013, JIS C 1509- 1:2017. The all models can perform simultaneous measurement of seven sound parameters including equivalent continuous sound level without adjusting the level range corresponding to the sound fluctuation and display the selected parameters.
-
Product
Audio/ Video
Audio Analyzer
Our experts/ physicist can help you in the Implementation of your algorithms including BPR, NUC , Edge Detection and movement analysis algorithms.Our development environment is based on C++ and LabVIEW libraries or tools such as Vision Builder for Automated Inspection from National Instruments.
-
Product
Non-Contact H.V. Detector
375 HP
-
Standard Electric Works Co., Ltd
● Protection class : IP65.● 8 voltage settings : 240V, 2kV, 6kV, 11kV, 22kV, 33kV, 132kV, 275kV● Bright LED visual indication● Frequency range: 40~70Hz● Flashlight funcion●Wider angle for voltage detection(120°)●Audible indication● Easy-to-prove method● Self-test function● Power source : 1.5V "C" type battery × 3● High impact nylon casing● Non-contact work by proximity● Compatible with most hot sticks● Lightweight, robust & compact● Suitable for indoor and outdoor use● Easy access to batteries.● Special ranges are available upon request. ● The maximum detection range can be 500kV.● Meets EN 61326-1 CISPR 11 EN 61000-4-2 EN 61000-4-3 EN 61000-4-8
-
Product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Tinned Ends, 1m, HV
A037DF4-T-HA100
Cable Assembly
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
4W - Single Output
KAS series
-
*90 - 305VAC Input Voltage*Class II (No ground needed)*Wide Temperature Range (-40 to +80°C)*Low off-load Power Draw*High Efficiency
-
Product
SHDE9F-DE9F-FX Flexray Cable, No Termination, 1M
198290-01
-
9-Pin, Female D-SUB to 9-Pin, Female D-SUB FlexRay Cable - The SHD9F-D9F FlexRay Cable connects FlexRay interfaces to devices, breakout boxes, other interfaces, and accessories. This cable meets FlexRay cabling specifications and is compatible with all NI-XNET FlexRay interfaces. It offers 82 dB/km attenuation with no termination. The cable’s impedance is 100 Ω, 148.94 Ω/km at 20 °C resistance, and 5.2 ns/m delay. The cable features four 26 AWG twisted pairs and dedicated pairs for FlexRay Bus A and Bus B.
-
Product
USHIO Red Laser Diodes (633nm - 690nm)
-
The Optoelectronics Company Ltd
Features: 5.6 mm CAN package, Optical output power: 80 mW (CW), 300 mW (pulsed – pulse width: 10 ns, duty: 10%), Lasing wavelength: 658 nm, Wall-plug efficiency*: 33%, Operating temperature: -10° – +60° C (CW); -10° – +75° C (pulsed), Single transverse mode, TE mode oscillation, MTTF >10,000 hours
-
Product
3.5" Embedded SBC With Intel® Pentium® Processor N4200 & Celeron® Processor N3350, VGA/LVDS, Dual LANs And Audio
CAPA318
-
The CAPA318 features the Intel® Pentium® processor N4200 or Celeron® processor N3350 (codename: Apollo Lake) with low power consumption. The integrated 3.5-inch embedded board is highly expandable and customizable. It comes with RS-232 ports, USB 3.0 ports, USB 2.0 ports, IN/OUT digital I/O ports, VGA port, LVDS port, and Gigabit Ethernet ports with Intel® i211AT Ethernet controller. For storage needs, the CAPA318 provides one SATA-600 socket and one mSATA interface. Additionally, Its compact and fanless design makes it perfect for use in space constricting environments. Additionally, the 3.5” single board computer can handle a wide operating temperature range from -20°C to +70°C (-4°F to +158°F) and requires +12V DC power input to ensure operational stability in a variety of harsh environments. This cost-effective 3.5” embedded motherboard is suitable for IoT/M2M related applications, industrial control, self-service terminals, digital signage, POS/kiosk displays, just name a few.
-
Product
PXI Multifunction I/O Module
Multifunction I/O
The PXI Multifunction I/O Module provides I/O with varying numbers of channels, sample rates, and output rates with precise timing, triggering, and synchronization between models. This module can be used for industry applications such as laboratory research, design verification test, and manufacturing test.The PXI Multifunction I/O Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
NI-9474, 30 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module
779003-01
Digital Module
30 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module - The NI‑9474 works with industrial logic levels and signals to directly connect to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 5 V to 30 V, features transient overvoltage protection between the output channels and earth ground, and has a LED that indicates the status. The NI‑9474 is a correlated digital module, so it can perform correlated operations, triggering, and synchronization when installed in a CompactDAQ chassis.
-
Product
Crossed-Roller Bearing Linear Stage ,25mm Travel XY,Sensitivity 1um
NFP-2462
-
Model:NFP-2462 Crossed-Roller Bearing Linear Stage ,25mm Travel XY,Sensitivity 1um DetailsSpec: Please refer to NFP-1462 Specification,It is combinated by 2pcs NFP-1462(C,SR,SL)
-
Product
Manual Step Attenuator, DC to 4 GHz, 0 to 70 dB, 10 dB steps
8495A
Attenuator
The Keysight 8495A dc to 4 GHz manual step attenuator offers exceptional repeatability and reliability. Attenuation is provided in 10 dB steps from 0 to 70 dB. Precision gold-plated leaf springs ensure long life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
-
Product
Software
ITS Lite
-
The BAUR software ITS Lite is used to read, design and archive measurement logs of the DPA 75 C, DTA 100 C, DTA 100 C, DTL C BAUR oil testers. Automatic archiving of measurement logs in PDF format and as text file (*.txt) Structured storage and allocation of measurement logs Customised layout of measurement logs Fast and uncomplicated access to measurement data
-
Product
DC/DC Converter 50 W
CTS-60-6843
-
DC/DC converter with 50 W from Premium | input ranges 43.2 - 90 VDC | output 5 V | operates in temperatures from -25 - +85 °C | designed according to EN50155
-
Product
Radar solution for width measurement of steel & metal
-
The OndoSense radar sensor solution determines the width of steel plates, steel strips or steel slabs (up to 1600 °C hot) with an accuracy of up to ±300 µm. Thanks to robust radar technology, sophisticated signal processing and smart radar algorithms, our radar sensors offer this high precision in width measurement even in the extreme production environments of the metal and steel industry.
-
Product
NI-9862, CAN Interface Module
781639-01
Interface Module
1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module—The NI‑9862 is a high-speed Controller Area Network (CAN) Flexible Data‑rate (FD) interface for developing applications with the NI‑XNET driver. The NI‑9862 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
Product
Carbon Monoxide Meter
ET110
-
The ET110 is an easy-to-use meter that detects and measures concentration levels of carbon monoxide (ppm) and temperature (oF/oC) making it the perfect choice for HVAC professionals. Backlit display with CO measurements (0 to 1000 ppm) and temperature (°F/°C ).
