-
Product
IR Carbon and Sulphur Analyzer
LD-LCSA-A12
-
IR Carbon and Sulphur Analyzer LCSA–A12 is a unit for determination of sulphur and carbon equipped with two treatment units including a high frequency induction burner and flexible temperature settings with automatic control. With an analysis time of 25 to 60 seconds and 10 to 30 °C, the multi-shielded isolation circuit prevents the machine for high frequency interference. High speed 32-bit sampling improves sensitivity and accuracy.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Male, 2m HV, Exit Away From Pin 1
40-970-050-2m-MM-HV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Constant Temperature Humidity Battery Test Chamber
-
Guangdong Test EQ Equipment co., Ltd.
- Battery-Specific Thermal Management: Dual-compressor cascade cooling (-40°C stability) and ceramic heaters for rapid high-temperature recovery.- Precision Electrochemical Control: Integrated battery cyclers with CAN/Modbus protocols, supporting SOP (State of Power), SOH (State of Health), and DCR (Direct Current Resistance) monitoring.- Safety-Centric Design-meet Hazard Level: Chambers are designed with Fire-resistant stainless steel interior, fire suppression,nitrogen purge system, and emergency power cutoff for thermal runaway prevention .- Data Acquisition & AI Analytics: Real-time logging of voltage, current, temperature, and pressure via LabVIEW/Python APIs. AI-driven anomaly detection reduces test cycles by 30%.- Energy Efficiency and Energy Storage: Heat recovery during discharge cycles cuts energy use by 25% (ISO 50001 compliant).
-
Product
VME J2 9 slot
101VMEJ209-0900
-
VME J2 backplane 9 slot, compliant with ANSI/VITA 1-1994. The A+C rows are bussed in all slots. Also, row B has onboard, inboard termination.
-
Product
NI-9149, 8-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis
783376-02
Chassis
8-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis - The NI‑9149 is a rugged Ethernet chassis that you can use to add C Series I/O modules to any standard Ethernet network. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. With the NI‑9149, you can add high-performance I/O to your PC-based application or expand your CompactRIO, PXI, or industrial controller application.
-
Product
Hardness Testers
-
Dalian Taijia Technology Co.,Ltd
Digital durometer for shore hardness testing pocket size model with integrated probe● Test scale: shore hardness● Standards: DIN53505, ASTMD2240, ISO7619, JISK7215● Parameters displayed: hardness result, average value, max. value● Measurement range:0-100HA(HD)(HC)● Measurement deviation:＜1%H● Resolution: 0.1● Auto switch off● With RS232C interface● Operating conditions: 0℃ to 40℃● Power supply: 4x1.5V AAA (UM-4) battery● Battery indicator: low battery indicator● Dimensions: 162x65x38mm● Weight (not including probe):173g● Application:Shore A is designed to measure the penetration hardness of rubber, elastomers and other rubber like substances such as neoprene, silicone, and vinyl. It can also be used for soft plastics, felt, leather and similar materials.Shore D is designed for plastics, Formica, Epoxies and Plexiglass.shore C is designed for various foam and sponge.
-
Product
NI-9853, CAN Interface Module
780178-01
CAN Interface
2-Port, High-Speed C Series CAN Interface Module—The NI‑9853 is a high-speed Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9853 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9853 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9853 is only compatible with CompactRIO systems.
-
Product
IR Calibration Instruments
-
Bodkin Design & Engineering, llc
We offer a line of comprehensive solutions to address all of your thermal calibration needs. From bench-top differential sources with .01° C resolution for experiment calibration to built-in OEM devices for on-the-fly thermal reference, Bodkin Design and Engineering and IRBlackbody have the right blackbody for you.
-
Product
DC/DC Converter 140 W
CTS-120-6887-D
-
DC/DC converter with 140 W from Premium | input ranges 21.6 - 47 VDC | output 24 V | operates in temperatures from -25 to +85 °C | designed according to EN50155
-
Product
D C DIELECTRIC STRENGTH TESTERS ( HIPOTS )
DV-25V-5
-
D C DIELECTRIC STRENGTH TESTERS ( HIPOTS ). One voltmeter 0-2500V dc accuracy: 2% of full scale. 4 Lights (power-on, high-voltage-on, fault and line-fault)
-
Product
DC/DC Converter 2 W
REM2-1512D
-
DC/DC converter 2 W from Recom | input ranges 13.5 - 16.5 VDC | outputs +/-12 V | operates in ambient temperature from -40 to +95 °C
-
Product
CX4000 – FTIR Gas Analyzer
-
Gasmet CX4000 is an industrial multi-component FTIR gas analyzer for continuous emission monitoring applications, integrated into a Continuous Emissions Monitoring system (CEMS II e). It can be used to measure up to 50 components simultaneously, and additional gases can be easily added without any hardware changes. The corrosion-resistant sample cell is heated up to 180 °C, which makes CX4000 an ideal tool for analyzing trace concentrations of pollutants in wet, corrosive gas mixtures.
-
Product
Mezzanine Carrier
VXI NM-M
-
HM-M is a carrier of mezzanine modules in the VXI standard, it is a VXI module of the size C-1. NM-M ensures the functioning of various modules installed in it, made in the form of mezzanines. NM-M is intended for use as a mezzanine carrier in multichannel systems for collecting / issuing information, both digital and analog. The carrier of the NM-M mezzanine modules is used as part of information measuring systems based on the VXIbus trunk. Made on a C size board in accordance with the requirements of the IEEE Std 1155-1992 standard.
-
Product
sbRIO-9218, Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module
783362-02
Analog Input Module
Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module - The sbRIO‑9218 helps you perform multipurpose testing. With the sbRIO‑9218, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors. You also can use the sbRIO‑9218 to perform quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. You can individually select and perform a different measurement type on each channel. Additionally, the sbRIO‑9218 features 60 VDC analog input isolation. Non-enclosed modules are designed for OEM applications.
-
Product
NI-9201 , ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
779013-01
Module
±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9201 is an effective combination of channel count and speed at a low price for an economical multifunction system. The module features up to 100 V of overvoltage protection for errant signal connection or unexpected signals to the individual channels.
-
Product
NI-9775 , ±10 V, Up to 20 MS/s/ch, 14-Bit, 4-Channel C Series Digitizer Module
784539-01
Digitizer
The NI-9775 provides referenced single-ended analog inputs with two timing modes for applications such as fault detection in electrical transmission lines or structural failure events. You can use the NI-9775 to measure finite samples up to 20 MS/s/ch to capture fault detections or to measure continuously at up to 4 MS/s. You also can use the built-in analog reference trigger to assist with high speed phenomena. Additionally, the NI-9775 supports waveform streaming at a lower sample rate.
-
Product
32-CH Sinking Type Digital Input EtherCAT Module
EPS-1132
-
*32-CH sinking type digital input*Quick removable European type connector*Slave module healthy monitoring*Wide operation temperature range: -20°C - 60°C*Compact size: 100 (L) x 100 (H) mm
-
Product
Intelligent Interface Card
IIB-1553-MMA
-
The IIB-1553-MMA is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the M-Module standard, with 1553A, 1553B, McAir and STANAG 3838 variants in one card. The IIB-1553-MMA supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, withcomprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
Product
Submersible, Temperature Data Logger
Temp1000IS
-
The Temp1000IS temperature data logger is a rugged, submersible, battery powered, stand alone device which can be used to automatically record temperatures between -20 and 80°C. This all in one compact, portable, easy to use device is able to measure and record data for up to 32,767 temperature readings.
-
Product
15W to 30W - Single Output
CC-P-E Series
-
*Compact Footprint / Low Profile*18-36 Vdc, 36-76 Vdc Inputs*3.3, 5, 12, 15 Vdc Outputs*Isolation: 1 kVdc (Case); 1.5 kVdc (Uncased)*-40 to 85 °C Operating Temperature*Parallel Operation
-
Product
AC/DC Power Supply 20 W
CFM21M150-E
-
AC/DC power supply with 20 W from Cincon | input ranges 90 - 264 VAC | output 15 V | operates in temperature from -25 to +70 °C | provides 2 MOOP safety and is class II | enclosed version
-
Product
Digital Probe Thermometer
TA288
-
A multi-purpose thermometer for your laboratory, workbench or office. Simple to use and provides a clear digital readout in °C or °F. a sharp and sensitive metal probe, and a protective plastic sheath
-
Product
Multifunction I/O Device
Multifunction I/O
The Multifunction I/O Device features I/O with varying channels, sample rates, output rates, and other features to meet many common measurement requirements. You can use the device for industry applications such as laboratory automation, research, and design verification. The included DAQExpress companion software provides basic measurement and analysis, while the included NI-DAQmx driver provides the ability to create customized automated measurement and control applications. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
90 Degree Hybrid Couplers To 600 MHz
-
This category of hybrid dividers features designs from 5 to 600 MHz with 2:1 to 4:1 bandwidth. Maximum insertion loss of 0.5 dB is specified for most units. These 90-degree hybrids are designed for a power rating of 1 watt maximum for a load VSWR of 1.2:1 or better. For use in 50-ohm environments.Pulsar Microwave currently offers this product line in three space-saving packages. The connectorized outline 412 comes standard with SMA female connectors. Outline C is a surface mount package useful for handheld applications with limited PCB area. Outline 301 is hermetically sealed for rugged environments.
-
Product
NI-9265, 4-Channel C Series Current Output Module
779334-01
Current Output Module
4-Channel C Series Current Output Module - The NI‑9265 is ideal for interfacing and controlling industrial current-driven actuators at high rates. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing … outputs to ensure safety and avoid driving actuators at system power on. The NI‑9265 requires an external power supply and includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
Product
LCR Meter
ST5C Colibri
-
*Built-in direct LCR probe*Convenient one-hand operation*Ideal for Surface Mount Devices*Automated component identification*Automated test range selection*Manual C, R, L and ESR modes*Manual test frequency overrides*Test signal level 0.5 Vrms*Portable and ergonomic design*OLED Display*Built-in Li-Ion battery
-
Product
AC/DC Power Supply 20 W
CFM21S240-T
-
AC/DC power supply with 20 W from Cincon | input ranges 90 - 264 VAC | output 24 V | operates in temperature from -25 to +70 °C | provides 2 MOOP safety | JST connector
-
Product
Cable Assembly, 50-Pin D-Type, Male to Male, 1m HV, Exit Towards Pin 1
A050DM5-050DM5-HA100
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Infrared Thermometers
-
Instant, less-than-a-second temperature readings of any surface, °F/°C switchableIdeal for food preparation, pharmaceuticals, field use, electronics, and safety inspectionFeatures minimum/maximum memory, average readings, and high/low audible alarms (Cat. No 4484)
-
Product
Bench Power Supply, Calibrated w/D & U, Adjustable, 1 Output, 0 V, 30 V, 0 A, 5 A
72-2690 CAL DU
-
The 72-2690 CAL DU from Tenma is a single channel adjustable bench top power supply. It is a digitally controlled industrial grade power supply with load for a long time. This compact design power supply has complete digital control, intelligent temperature controlled fan, low noise and low ripple. It also features knob lock function to avoid improper operation. This power supply has load regulation ≤0.01% +2mV (voltage), ≤0.1% +5mA (current) and line regulation of ≤0.01% +3mV (voltage), ≤0.1% +3mA (current). The setting accuracy (25°C ±5°C) is ≤0.5% +20mV (voltage), ≤0.5% +10mA (current).
