Current Transformer Test Set
See Also: Transformer Test, Transformer Testers, Current Transformer Test
-
Product
Capacitor Test
-
Delta United Instrument Co., Ltd.
Specialized, high-efficiency automatic testing systems for electrolytic capacitors.
-
Product
Strength Testing
-
Sataton Instruments Technology CO., Ltd
Air permeability tester is professional designed to determine the permeability of materials to air. By testing the rate of flow of air passing perpendicularly through a given area of tested sample under a given pressure over a given time period, the tester can provide results of air permeability performance by calculation the indices. The air permeability testing instrument is applicable to many type of materials, including industrial fabrics, nonwovens, made-up textiles, paper and board, foam and other materials.
-
Product
Unit Testing
-
Hitex offers a unit testing service for C/C++ application source code using the well-known test tool TESSY. For this service, the customer provides their source code of the C/C++ functions to be tested, ideally along with the specifications of the functionality and comprehensive comments in the source code.
-
Product
Current Probe
DCP-BTA
-
Vernier Software & Technology, LLC
The Current Probe measures DC and low-frequency AC currents up to 600 mA. Use Current Probes in combination with Differential Voltage Probes to investigate Ohm's Law and explore series and parallel circuits. The 0.1 shunt resistor minimizes changes to your circuit. If currents will exceed 1 A, use the High Current Sensor.
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-40PS
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 1A～500A*Current measurements of feeder
-
Product
Selectable Shunt Current Sensor ±40 V, 20 MHz
CX1104A
-
The CX1104A selectable shunt current sensor is a dedicated accessory for the CX3300 series and enables dynamic current measurements from 1 μA to 15 A up to 20 MHz bandwidth with an available calibrated resistive sensor head attached
-
Product
Conformance Testing
Clarinet-TTCN ATM ETS
-
Protocol: UNI 3.1 ATM Layer Conformance Test Suite for End SystemsIUT: ATM Equipment UNI 3.0ATS: ATM-FORUM standards af-test-0060.000 covers the test of UNI 3.0 ATM Layer of End Systems
-
Product
Portable Multi Phase protection relay test set with GPS
TEST-630
-
Beijing GFUVE Electronics Co.,Ltd.
Test-630 multi Phase Universal protection relay test set have 6U6I output, it is a universal protection relay tester with eight pairs of binary input and four pairs of binary output
-
Product
Accessibility Testing
-
More than a compliance requirement, accessibility of your applications to ensure inclusivity of differently abled populations is a societal responsibility. As a socially responsible organization, you would like your applications and products to be accessible for one and all, including people with visual, hearing, cognitive and motor limitations. It also helps your brand image and increases the number of happy users.
-
Product
AC and DC Non Inductive Current Shunt
Series A co-axial shunt and Option 02F/B shunt
-
Use with wattmeters, DMMs and power analyzers to extend current measurement ranges. Use with phase angle meters to enable phase angle measurements between voltage and current. Ultra low phase shift
-
Product
Single Gas Transformer DGA
-
Hydran composite gas Dissolved Gas Analysis (DGA) products provide essential online monitoring of transformer oil. The Hydran line is the perfect cost-effective application for small- and medium-sized transformers where customers need to know about developing fault conditions that could cause unscheduled outages.The Hydran products allow for the addition of expansion to the base unit, allowing for greater measurement accuracy
-
Product
Hipot Current Calibration Load Resistors
HPRS-HIPOT-LOAD
-
The IET HPRS-Hipot-Load is an excellent replacement for the Fluke 5320A-Load Hipot current calibration load resistors. The IET high power resistive load can be used with the Fluke 5320A Multifunction Electrical Tester Calibrator or standalone. It provides a high power and high voltage load to various hipot tester to create the leakage current needed to calibrate various manufactures hipot testers.
-
Product
Fuse Buddy Current Loop
307M/308B
-
*Just clamp your current probe over the loop to access the amperage draw through a fused circuit. *Easy testing access, plugs right into fuse socket, no more hand made adapters. *Testing range 0-30 Amps - Do Not Exceed 30 Amps
-
Product
Complete Transformer Test Bench
-
Weshine Electric Manufacturing Co., Ltd
Our multifunction Transformer Test Bench (VS-ZHSY Series) is intuitive with all of the ease of working with individual, dedicated instruments. We deliver this experience through our design philosophy. Rather than producing a single, complex system with afterthought towards rendering it friendly, we uniquely combine several intelligent instruments packaged as a single system.
-
Product
Test Module
MTC
-
The measuring channels can be connected depending on the application to the pins on the system interface or to the six internal bus lines.Four measuring channels per module on 8:1 multiplexer = 32 InputsUp to 4 parallel measurements per MTC (4 parallel counters)Intelligent algorithms for fast measurements even at low frequenciesFrequency, period, pulse width, rise- and falling time as well as event counting on each channelTime measuring range: 10 ns - 42 s, resolution 10 nsFrequency measuring range: 0.015 - 100 MHzEvent counting: 0 - 232, maximum 100 MHzMax. input level/trigger voltage: +/-100 VSynchronization with external trigger possible
-
Product
AC Current Probes
CWT
-
Power Electronic Measurments Ltd
The CWT Rogowski current probe is suitable for measuring AC currents ranging from 300 milliamps to hundreds of kA from below 0.1Hz to >30MHz.
-
Product
Test Engines
-
Verified Systems International GMBH
The test system cluster architecture is based on dual CPU or 4-CPU PCs acting as cluster nodes. The nodes communicate and synchronise over a high-speed network (Myrinet or InfiniBand). A modification of the Linux operating system allows to run the test execution and evaluation algorithms in hard real-time on reserved CPUs, where scheduling is non-preemptive and controlled by the test system itself. The interrupts caused by interfaces to the system under test may be relayed to CPUs designated explicitly for their handling. This approach offers the opportunity to utilise high-performance standard hardware and the services provided by the widely accepted Linux operating system in combination with all mechanisms required for hard real-time computing. The cluster architecture presents an opportunity to distribute interfaces with high data throughput on different nodes, so that PCI bus overload can be avoided. In addition, the CPU load can be balanced by allocating test data generators, environment simulations and checkers for the behaviour of the system under test ("test oracles") on dedicated CPUs.
-
Product
Test Fixtures
-
REINHARDT System- und Messelectronic GmbH
Is a fixed state of a set of objects used as a baseline for running tests. The purpose of a test fixture is to ensure that there is a well known and fixed environment in which tests are run so that results are repeatable.
-
Product
T3CP Series AC/DC Current Probes
T3CP Series
-
Teledyne Test Tools AC/DC Current Probes are powered by an external universal power supply and work with any Oscilloscope with a high-impedance BNC input. The range of five current probes includes models with bandwidths up to 100 MHz, peak currents up to 500A and sensitivities to 1 mA/div.
-
Product
Flux Testing Transformer
-
The testing equipment is manufactured in strict adherence with industry standards using superior quality raw materials, sourced from reputed vendor in market.
-
Product
Leakage Current Tester
2675
-
Shenzhen Chuangxin Instruments Co., Ltd.
RK2675 series Leakage Current Tester is used to measure the electrical insulation quality and products’ safety performance of the main indicators.
-
Product
Continuity Testing
-
The checking of an electric circuit to see if current flows (that it is in fact a complete circuit).
-
Product
Rotor Testing
-
Rotor testing equipment is capable of testing cast rotors of a range of sized and variety of designs. It is operator friendly and easy to maintain. It has data acquisition system that operates through software on PC. It offers high level analysis of individual measurement. Also allows maintaining records & generating reports with ease and flexibility.
-
Product
Telcom Test Sets
T62 Recon
-
The RECON is the first true 21st century telecommunication line analyzer setting a new standard for POTS butt sets. It is a field instrument that delivers more information of online conditions & status than any other test set on the market, anywhere in the world!!
-
Product
Incremental Transformer Solutions
TRANSPORT X
-
The Kelman TRANSPORT X is a compact portable Dissolved Gas Analysis (DGA) system which can be used to analyze oil samples for all dissolved fault gases and moisture. If abnormal levels are detected, it further provides a diagnostic using various IEEE/IEC approved interpretation rules.
-
Product
Testing Services
-
DTB is the largest independent testing laboratory in the United States with a full spectrum of testing services all under one roof. We provide a wide range of environmental, dynamics and vibration, EMI/EMC, ballistics, optical, ordnance release, and safety and survival testing.
-
Product
Slot 0 Module Retainer Block Set, For Discrete Wiring, 1 Position
510109150
-
These module retainer blocks are used to attach modules directly to the inner frame of a VXI receiver for discrete wiring. These modules then hinge down with the receiver to provide easy access to wiring.
-
Product
Compliance Test, Development and Test Service
DinoStor
-
With its focus on solving critical backup problems associated with Network-Attached Storage (NAS), DinoStor delivers a broad range of products and services to benefit users and vendors of NAS solutions.
-
Product
CARB Testing
-
Underwriters Laboratories Inc.
The ASTM D6007 (small chamber) and ASTM E1333 (large chamber) test methods are used by the composite wood products industry to measure emissions of formaldehyde from plywood, particle board and medium-density fiberboard (MDF), commonly known as CARB testing. Testing is conducted in environmental chambers operated at defined product loading, temperature and relative humidity.
-
Product
Split Type AC Current Sensor
CTF-16
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Wide measuring range (AC 0.1～100A).*Compliant with RoHS drective.
