Current Transformer Test Set
See Also: Transformer Test, Transformer Testers, Current Transformer Test
-
Product
Mechanical Testing
-
A range of processes including:Tensile and Compression Load TestingA test piece or component is subjected to tension (or compression) until either a proof load is achieved or failure occurs.Testing can be carried out on both metallic and some non-metallic materials.
-
Product
Test Probe
UE
-
Qosmotec Software Solutions GmbH
Qosmotec UE Test Probe offers more flexibility to testers of mobile networks. It is a compact plug & play multi-UE test probe that allows for tests in UMTS, HSPA+ and LTE standards from any location. It can hold a custom set of up to 8 UEs.
-
Product
Package Testing
-
Package testing helps manufacturers verify their package designs to ensure that their products will not experience damage during shipping. Products are often shipped across states, countries and continents to reach their destination. This is an unavoidable link in the supply chain and, as such, packaging must be designed to protect products during the shipping process.
-
Product
EMI/EMC Testing
-
EMI/EMC testing can reliably predict product performance in any electromagnetic environment. Testing can also determine the possibility of interference with other equipment, possibly degrading performance. Testing may be required in order to comply with regulations or for informational and product improvement purposes.
-
Product
In-fuse Vehicle Current Measurement System
Sens-X
-
Sens-X intelligent sensors offer a range of high dynamic range sensor hardware for the capture of specialist current measurements.
-
Product
Sealed Beam Bulb Testing System
H710019SSL
-
EOL test for manufacturing of bulbs with LED for applications requiring to ensure watertightness: vehicles, marine, swimming pools, operating rooms, classified areas (Ex Zone), etc. The test system checks in a short time all the light and electrical characteristics of the bulb. A high precision Micro Leakage Meter also checks that there are no leaks between the environment and the inside of the bulb. The test results are recorded on the PC and can be printed on a quality control label attached to each unit.
-
Product
Low Input Bias Current Amplifiers (<100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
Test Systems
-
This measurement system is the state-of-the-art acoustical analyser from Norsonic. Using the experiences and accumulated know-how from the previous generations of analysers, Norsonic is offering a multi-channel system with focus on user friendliness, high efficiency, and accurate reporting. The system has been designed for field testing as well as demanding accredited lab measurements.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-200B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
ANSI Relaying Current Transformer Burden
-
The ANSI Current transformer burden is designed for loading the current transformer during accuracy Tests. The ANSI burden is designed as per ANSI burden C57.13.It can be used along with the Eltel Automatic Instrument Transformer Test Set to test CTs as per ANSI Standards.
-
Product
Portable Eddy Current Flaw Detectors
-
Portable eddy current (EC) flaw detectors inspect metallic parts and perform highly reliable and advanced flaw detection of surface and near-surface defects. Olympus offers portable eddy current equipment to meet a broad range of applications, including the detection of surface or near-surface defects, and the inspection of bolt holes.
-
Product
Vibration Test System
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Vibration Test System is a simulation of the various environments encountered in the manufacturing, assembly, transportation and use phases of execution. It is primarily used to identify the ability of a product to withstand environmental vibrations.
-
Product
Nanomechanical Test Instruments
-
Bruker has developed a comprehensive suite of nanomechanical and nanotribological test instruments that operate in conjunction with powerful microscopy techniques. Combining the advantages of advanced microscopy technologies with quantitative in-situ nanomechanical characterization enables an accelerated understanding of material behavior at the nanoscale.
-
Product
Wireless/RF Testing
-
NCEE’s experienced iNarte EMC/EMI qualified staff provide wireless and radio frequency (RF) testing of intentional radiators to ensure they meet the FCC, CE, and many other international regulatory requirements for transmitting and receiving (radio) devices. Frequent regulatory changes and complex testing requirements are common with wireless/RF equipment. NCEE Labs stays current with the most recent requirements and can help you navigate your requirements while supplying quality testing services to demonstrate worldwide compliance!
-
Product
HVDC Power Filter Characteristic Test Set
FT3000
-
FT3000 Power Filter Characteristic Testing equipment has the functions of automatic sweep harmonic signal output, A-F and P-F characteristic measurement/display etc. It can perform HVDC Power Filter Testing and is mainly used in AC filter of DC convertor station, DC filter tuning characteristics test and parameter test of R, L and C. It is also used in electrified railway HV filter, passive power filter client and conventional AC substation reactive compensation device.
-
Product
Digital Eddy Current Displacement Sensor
ZET 7140-S
-
A digital eddy current sensor consists of a primary transducer (eddy current probe) and the ZET 7140-S measuring unit.
-
Product
Station Of Acceptance Testing
-
The acceptance test station consists of a personal computer - the workstation of the operator of the testing station, contact mechanisms, as well as current and voltage sensors. The station allows to test up to 10 electric motors of various types simultaneously. The operator of the testing station indicates the test sites at which the engine tests will be conducted, their type (from the database), serial numbers and a set of tests.
-
Product
Parametric Test Solutions
-
Reduce your cost-of-test up to 20% with our ultra-fast CPU Overcome your process test challenges Boost measurement throughput and lower costs with our synchronous/asynchronous parallel test capability Better low-level measurement performance Create customized waveforms Reduce transition costs
-
Product
Test System
RF-1 ATS
-
The RF-1 ATS is an economical Commercial-Off-The Shelf (COTS) build-to-print tester. The test station is compliant with the published drawing package. The system does not include software.
-
Product
Circuit Breaker Testing
-
Weshine Electric Manufacturing Co., Ltd
Time measurement: 12 fracture intrinsic points, closing time, with the same period, phase with the same period.2. Reclosing measurement: each fracture closing - minute, minute - closing, minute - closing - minute process time, one minute time,one closing time, two closing time, gold short time, no current value.3. Bounce measurement: closing bounce time, bounce times, bounce waveform of each fracture, rebound amplitude of each fracture.
-
Product
Ramp or Flight line Air Data Tet Sets
-
The test sets are all digitally controlled through a local or remote keypad and display. The intuitive user interface allows test set functions to be easily controlled with a minimum of key strokes, with all test parameters displayed, and is suitable for both first time and more advanced users. Optionally many of the ADTS can be remotely controlled by a PDA Pocket PC with wireless Bluetooth connection. The intelligent user interface provides protection to both the test set and the UUT. The software rejects entered command values that exceed the pre-selected limit ranges.
-
Product
Strain and Fatigue Testing
-
ATA engineers have developed the skills and tools necessary to solve intricate and complex strength and fatigue problems.
-
-
Product
Functional Testing Service
-
Is your software working the way it is intended to? Will it work in the real world as it does in simulations? Is the code really executing as per its outlined specifications? Do various parts of the application interact as planned? Will users find the application functioning as per their requirements or will they get lost in the flow? Functional testing answers all these questions and more:- Tests your application against its intended output parameters to make sure it works the way it is meant to.- Tests if the functions of the application are working as intendedUnderstand if various parts of the application are interacting as planned.- Check if the user navigation is simple, free-flowing, and friction-less.- Functional Testing ensures optimum quality for content, design and user experience.
-
Product
Test Probes
-
Test Probes provide the vital link to transfer measurement signals as true and as undistorted as possible. Therefore these elements can be regarded as the heart of Test Fixtures – and for this very reason it is important for Equip-Test to offer high performance Test Probes with best quality and value, and thus ensure maximized ROI (Return of Investment) for our customers. Test Probes supplied by Equip-Test always provide the best-possible available solution for your contacting demands.
-
Product
Strain Gage Testing
-
Response Dynamics Vibration Engineering, Inc.
Although strain measurement is often a key part of a root cause diagnosis, our analyses often also involve measurements of other parameters such as acceleration, relative displacement, pressure, temperature, flow, speed, load, dynamic stiffness, etc, to explore multiple parameters that may have a cause/effect relationship with the problem at hand. These measurements form part of a fact based hypothesis for the cause of the problem at hand. We use stain gauge testing and/or stain modeling and analysis, in conjunction with our structural dynamics expertise to characterize all the important pieces of the puzzle that come into play with dynamic strain issues (See Diagnostic Testing).
-
Product
Test Leads
AL-34WB 10A
-
Standard Electric Works Co., Ltd
● Wire length: 1m approx. Silicone insulated wire (700mm) with wire connected to straight input plugs (150mm PVC wire), and wire for clamp (150mm PVC wire).● Outside diameter of silicone insulated wire: 6.4mm Outside diameter of PVC wire: 4mm● Input plug color: Red•Green•Black•Blue ● Current rating: 10A● Voltage rating: 300V● Designed for Milliohm meter, Micro-ohm meter, Low resistance measurement with high current injection. ● Conductor size: 40mm maximum● Safety standard: IEC/EN 61010-031 CAT IV 300V
-
Product
Calibration Foils Sets
990
-
The Elcometer 990 Calibration Foil Sets are ideal for use in the laboratory, on the production line or on site.
-
Product
Electrolyser Test Stations
-
Greenlight is the world''s leading supplier of test stands for both PEM and Alkaline electrolyser research. We have been manufacturing electrolyser testing equipment since 1996, and can provide references from major companies and research institutes worldwide.
-
Product
High Current Generators
-
Quantum Composers is a recognized industry leader for Current Pulsers and Firesets. We specifically design our units for use in pyrotechnic applications such as Aerospace, Defense, Propulsion, and Automotive Safety and Squib testing. Our current generators are used throughout the world in demanding and harsh testing environments where quality, reliability, and safety are paramount. We are also an excellent replacement and upgrade solution for legacy equipment.
