-
Product
8 Channel A/D & D/A Zynq UltraScale+ RFSoC Processor - SFF
Model 6350
-
- Now available in RFSoC Gen 3 with the Model 6353- Small form factor rugged enclosure- Conduction-cooled- Designed to the IP67 specification for dust and water immersion- Sealed military-grade circular connectors- Incorporates Xilinx® Zynq® UltraScale+" RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- Optional dual 100 GigE UDP optical interface- Optional fan cooling for benchtop use- Navigator® BSP for software development- Navigator® FDK for custom IP development- Pentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products Video- Live Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boards- Pipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoC- Please refer to the product datasheet for Installed FPGA IP Module details
-
Product
Evaluation Kits
-
Advantech ARM-based starter kit packages are including a main board, cables, power adapter, LED panel and an SD card.
-
Product
Boardmarker BMP1
549001
-
The so-called PCB markers (BMP-1 board markers) are used to mark assembled and unassembled PCBs as good. These are integrated into our adapters and draw a circle in each PCB that is found to be "good", provided the test device has the appropriate electronics and software.
-
Product
ISA Data Acquisition Boards
A-823PGH/S
-
The A-823PGH/L is 12-bit multifunction analog and digital I/O boards for the PC/AT compatible computer. The A-823PGH/L offer 16 single-ended or 8 differential analog inputs, plus two channels of analog output with 12-bits resolution. In addition, The A-823PGH/PGL has 16 digital input, 16 digital output , and one timer/counter channel. The A-823PGH Provides gain of 0.5, 1, 5, 10, 50 ,100 , 500 , 1000 while the A-823PGL provides gains of 0.5 , 1 , 2 , 4, 8 . It has a maximum sampling rate of 125 k Sample/Sec., DMA operation is jumper selectable for levels 1 or 3. Interrupts are jumper selectable between 3 and 15.
-
Product
SparkFun Analog/Digital MUX Breakout
CD74HC4067
-
This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067. This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx). It works with both digital and analog signals (the voltage can't be higher than VCC), and the connections function in either direction. To control it, connect 4 digital outputs to the chip's address select pins (S0-S3), and send it the binary address of the channel you want (see the datasheet for details). This allows you to connect up to 16 sensors to your system using only 5 pins!
-
Product
LUTHER & MAELZER BARE BOARD TEST PINS
SERIES LMP 78
-
Materials and Finishes MATERIAL: Heat treated beryllium copper FINISH: 24 Kt gold plate over hard electroless nickel
-
Product
Power Interface Board 3 HE, 2PSU-Steckverbinder
106PIBM302-0000R
-
The PIB 3U 2 slot has two power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
Dual Port Simulator Fiber Channel PCI Module
PCI-FC4 Simulyzer
Simulator
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. By simply upgrading the firmware / software, a single function board can become a full function board without having to purchase new hardware.
-
Product
PCIe I/O & Comm Board
79G5
Multifunction I/O
NAI's latest generation single-slot, half-size PCIe board, the 79G5 can be configured with up to three NAI intelligent I/O and communication function modules. Ideally suited for high channel density and combined multifunction I/O requirement systems, the 79G5 delivers off-the-shelf solutions that accelerate deployment of digital and analog I/O, position control and measurement/simulation and communication interface applications.
-
Product
Test Board For QSFP+ Transceiver
EQSFP10
-
The OPTELLENT EQSFP10 is a cost-effective and convenient test board for testing QSFP/QSFP+ optical transceivers in R&D and manufacturing environments. The EQSFP10 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The EQSFP10 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
Product
Intelligent Mini Munitions Store Interface (MMSI) Module for Excalibur 800 Family of Carrier Boards
M8KMMSI
-
The M8KMMSI is an intelligent, Mini Munitions Store Interface [MMSI] module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards. Each module of the M8KMMSI contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped and may be accessed in real time. Each M8KMMSI module may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT/Concurrent Monitor and Bus Monitor.The M4KMMSI comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
Product
Flex Test Fixtures
-
FTFs are test fixtures which are dedicated for testing flex-based components and assemblies such as displays, touch panels and more. A weak spot in a typical functional test system is the method to connect DUT flexible cable to a circuit board where the simple method of attaching the flex directly with an ZIF or LIF connector fails.
-
Product
Load Board
cPCI 6U
Load Module
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
Product
Optocoupler and Relay Cards
-
For easy connection and galvanic isolation of digital input or output signals, we offer various optocoupler and relay boards.
-
Product
USB Type-C Test Fixture | CB26U | Cable Harness Tester
-
A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test.
-
Product
Medium Range HD Multi-Spectral Surveillance System
TacFLIR® 280-HDEP
-
The TacFLIR 280-HDEP is an essential system for ground vehicle surveillance and fixed installations. With an all-new stabilized payload assembly for enhanced reliability, the TacFLIR 280-HDEP is ready for a variety of land missions, and the modular and scalable control electronics unit (CEU) is capable of hosting powerful video processing and Aided Target Recognition (AiTR), as well as third-party algorithms. Designed to meet the rigorous demands of military operations, the system delivers best-in-class EO/IR imagery and optional Display Interface Boards (DIB) which allow the operator to stream up to four independent video streams. In addition, there is also a removable terabyte hard drive w/DVR to record over 80 hours of compressed video and 250 screen captures.
-
Product
6U CompactPCI Rear Transition Module with Ruggedized M12 Connectors
cPCI-RMPSA
Rear Transition Module
- Dual display with DVI-I and DVI-D- Ruggedized USB 2.0, GbE M12 ports- Dual serial ports and optional USB 3.0- Compatible CPU boards: cPCI-6530/cPCI-6520/cPCI-6940
-
Product
Crosspoint Switches
-
Macom Technology Solutions Holdings Inc.
At MACOM we offer the industry’s largest portfolio of low latency crosspoint switch devices with channel counts ranging from 2x2 all the way up to 288x288, and data rates from 3.2 Gbps to 28 Gbps. Our devices are equipped with signal conditioning technology that enables system designers to use lower cost board materials and components while increasing their system margin.
-
Product
CAN/LIN Communications Expansion Kit
OP-SB87
-
OP-SB87 is an expansion board for CAN/LIN communications, inserting into a slot of communication analyzer LE-8200A/LE-8200. It has 2 CAN connectors and 2 LIN connectors, and measures 2 channels of CAN or LIN, or 1 CAN/1 LIN. It is useful to measure network where there are CAN and LIN communications at the same time.
-
Product
Function Tester with Low Number of Channels
UTP 6010 RF
-
The UTP 6010 is one of our smallest test systems and therefore a cost-effective entry into our UTP tester series.The fast system is used to implement scalable functional test applications for a test item (single device under test) with multiple RF channels and mixed-signal test options. Depending on the adapter, the DUT can be tested at circuit board level (FKT) or when installed at the end of the line (EOL).Depending on the test item requirements, we configure the appropriate number of channels and integrate the necessary interfaces directly in the adapter or tester. The test speed, production volume and overall complexity of the UTP 6010 interfaces can be varied according to your requirements.
-
Product
DB9 DIN-Rail Wiring Board
ADAM-3909
-
Low cost universal DIN-rail mounting screw terminal module for PC-LabCard™ products with DB9 connectorCase dimensions (W x L x H): 77.5 x 45 x 51 mm (3.1" x 1.8" x 2.0")To Be Used With PCI-1714U/UL, PCL-728, PCL-740, PCL-741, PCL-743B, PCL-745B
-
Product
Digital Output Board
VME-2128A
Digital Output Board
VME-2128A 128-bit High-Voltage Digital Output Board with Built-in-Test
-
Product
27" Open Frame Gaming Monitor
GM-270G
Gaming Monitor
ADLINK’s GM-270G is a 27-inch open frame gaming monitor designed for casino gaming applications, especially for embedded slot machines or video lottery terminals. ADLINK offers highly flexible customization service, with customization options for cover glass, scaler board, and firmware.
-
Product
BGA Sockets
-
Ironwood has the most comprehensive collection of BGA (Ball Grid Array) sockets that can be used for prototype application, silicon validation, system development, thermal characterization, burn-in application, functional production test, etc. BGA socket can be defined as an electromechanical device, which provides removable interface between IC package and system circuit board with minimal effect on signal integrity. BGA sockets for prototype applications, silicon validations, system development applications uses low cost elastomer contact technology.
-
Product
SparkFun Soil Moisture Sensor (with Screw Terminals)
-
The SparkFun Soil Moisture Sensor is a simple breakout for measuring the moisture in soil and similar materials. The soil moisture sensor is pretty straightforward to use. The two large, exposed pads function as probes for the sensor, together acting as a variable resistor. The more water that is in the soil means the better the conductivity between the pads will be, resulting in a lower resistance and a higher SIG out. This version of the Soil Moisture Sensor includes a 3-pin screw pin terminal pre-soldered to the board for easy wiring and setup.
-
Product
Electronics Design Software
Altium Designer
-
Professional unified design system, high productivity stress-free environment and native 3D PCB editor. Easily design the most complex and innovative board layouts with advanced and accessible routing tools. Stay at the frontline of innovative technology development with the world's first-and-only support for rigid-flex PCB design.
-
Product
PCIe-Mini Module
PCIe-Mini-ARINC429-4/8
Controller
The PCIe-ARINC429-4/8 PCIexpress Mini board has an ARINC controller that supports the ARINC specifications. ARINC429 (Aeronautical Radio Incorporated) is a specification, which defines how avionics equipment and system should communicate with each other. ARINC 429 employs a unidirectional data bus standard known as Mark 33 Digital Information Transfer System (DITS). Messages are transmitted and received at a bit rate of either 12.5kbps or 100kbps.
-
Product
Test Contactor
MiCon
-
The MiCon™ Test Contactor is spring pin footprint compatible supporting advanced temperature requirements as well as advanced power/current requirements. The footprint compatibility allows for easy and cost-efficient conversion from spring pin setups. The fully decoupled load board side of the spring ensure no degradation of the load board pad.MiCon features a single piece design, which ensures a long lifespan, low and stable contact resistance, high current carrying capability and an extended temperature range. The MiCon allows for testing at full specification values. The extended operating range accommodates device lead trim and form variability such as device alignment accuracy and device lead coplanarity.
-
Product
Peripheral Boards
-
Advantech CPCI solution includes GPU, Ethernet, storage blades, and AC/DC power modules that comply with industry standards for broad compatibility.
-
Product
FMC Card with DisplayPort Input and Output
TEF0007-02A
-
Sundance Multiprocessor Technology Ltd.
The Trenz Electronic TEF0007 is a DisplayPort 1.2 compatible FMC card with data rates up to 5.4 Gbps and sink and source DP connector. SN65DP159 is used as DP Retimer and SN75DP130 as DP Redriver to connect sink and source to on board Kintex-7 FPGA.Image stream over FMC can be realized over 4 MGTs (only 1 available on LPC) and 34 differential IOs (LPC compatible).
