Cards
See Also: Extender Cards, Probe Cards, POST Cards, Test Cards, Boards, Modules
-
Product
Micro-D (Male)
Micro-D (Male)
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 100-pin Micro-D connector.
-
Product
Extrusion Rail
1440-0132-84
-
VECTOR Electronics and Technology, Inc.
To accommodate guide rails and attach backplanes.HP pitch pattern of holes for precise installation of card guides.M4 threaded at ends.
-
Product
Smart Gas Meters
-
FQ prepaid IC card gas meter is used for measuring the flow of gas in the pipe.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 2.5Ω To 3.55kΩ
50-298-123
Programmable Resistor Module
The 50-298-123 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 3.55kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
6U Horizontal Card
2270
-
VECTOR Electronics and Technology, Inc.
Versatile chassis for horizontal card installation
-
Product
Generator/Analyzer for NFC/EMVCo Manufacturing Test
Micropross MP500 PT1-NFC
test
Support for ISO 14443 A/B, ISO 15693, MIFARE™, FeliCa™. Measurement correlation with NFC Forum and EMVCo certification test bench. Automated test executive with ready-to-run test sequences. Reader/Writer and Card Emulation modes, resonance frequency measurements supported on same antenna. Embedded analog measurements - LMA, field strength, S11, Q factor, waveform characteristics. Physical parameter/waveshape characteristic definition
-
Product
PCIe Octave Express 14-Bit Digitizer
Digitizer
The GaGe Octave Express 83XX CompuScope PCIe digitizer card features 14-bit resolution with sampling rates up to 125 MS/s with true Effective Number of Bits (ENOB) of 11.1-bits with 10 MHz input.
-
Product
In-circuit Test
Medalist i1000 Systems
-
Cover Extend Technology (CET) is now supported on the Medalist i1000D. The i1000D only requires a VTEP MUX card to enable CET. If you are already using test fixtures with VTEP MUX cards , you can now implement CET without any fixture modification. Simply add new VTEP probes to devices that were previously not testable. This greatly reduces implementation efforts.
-
Product
cRIO-9048, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 8-Slot CompactRIO Controller
785619-01
Embedded Controller
1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 8-Slot CompactRIO Controller - The cRIO-9048 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 160T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
cPCI to PMC Adapter / Carrier
cPCI2PMC
-
The cPCI2PMC ( cPCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard cPCI slot. The cPCI2PMC has a PMC card slot mounted to a universal 3U 4HP cPCI card. Suitable for 32/64 with 33/ 66 MHz bus operation. The PMC user IO connector Pn4 is optionally connected to J2 for rear panel IO.
-
Product
Rugged IP67-rated Fanless Embedded System With Intel® Core™ I5-7300U & Celeron® 3965U, VGA, GbE LAN, 2 USB, 2 COM And 9 To 36 VDC
eBOX800-511-FL
-
The eBOX800-511-FL is a fanless embedded system with IP67-rated housing and M12 connectors for mission-critical environments. This rugged embedded system is powered by the onboard 7th generation Intel® CoreTM i5-7300U and Celeron® 3965U (formally codename: Kaby Lake) and comes with one 204-pin DDR4-2133 SO-DIMM slot with system memory up to 16GB. The eBOX800-511-FL is designed for enabling to function in harsh environments with power protection, a wide range operating temperature from -30°C to 60°C, operating shock tolerance up to 3G and 9-36V wide range DC input. Additionally, there are M12 lockable connectors and N-jack type waterproof antenna openings to meet the performance needs for outdoor critical applications such as facility condition monitoring. Furthermore, the fanless embedded box computer comes in great expansion possibilities, including flexible I/O connectors and two 2 PCI Express Mini Card slots. For enhanced platform security the eBOX800-511-FL provides Trusted Platform Module (TPM) 1.2 support.
-
Product
PCI Very High Density Multiplexer, 10-Channel, 8-Pole
50-670C-021-10/8
Multiplexer Module
The 50-670C-021-10/8 is a 10-channel, 8-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
Product
SD Host Tester / SD / EMMC Analyzer / SD Card Tester
SGDK400 (Analyzer for UHS-II)
-
SGDK400 is a UHS-II dedicated analyzer.
-
Product
ARINC429 PCI Express Mini Card
AMEE429-x
PCI Express Mini Card
The AMEE429-x is AIM’s new PCI Express Mini Card module targeted for embedded ARINC429 applications in an ultra-compact form factor.
-
Product
Continuous Time Interval Analyzers
GT668PXIe-1
-
GT668PXIe-1 cards can be expanded up to 36 Channels Single Ended Input in a single 3U PXI chassis.
-
Product
Fast 8 Bit PCIe Gen-2 Digitizer With 1x2 GS/s, 2x1 GS/s, 16GS Memory
Cobra Express 22G8
-
The Cobra CompuScope family of high-speed 8-bit digitizers provide a powerful combination of speed, memory, and bandwidth as well as a wide portfolio of advanced acquisition features on a single PCI Express or PCI card.
-
Product
VME64x 4U 84HP 8 Slots
-
Hartmann Electronic’s 8 slot 19” rack mountable VME solution – The VME64x 4U system. This VME chassis comes with two 250W cPCI hot-swap power supplies with room for up to 4 supplies and horizontally oriented card slots. This platform conforms to VITA 1.1-1997 while providing a low profile, practical packaging solution for high-performance processors.
-
Product
Avionics PXI Express (PXIe) Interface Card - Multi-Channel, Multi-Protocol, 1553, ARINC, WMUX Interface for PCIe
Interface Card
Alta Data Technologies’ PXI Express interface modules offer a wide range of MIL-STD-1553, ARINC and WMUX configuration options using Alta’s PMC cards on a single-slot PXI Express 3U carrier. The cards are based on the industry’s most advanced 32-bit FPGA protocol engines, AltaCore™, and by a feature-rich application programming interface, AltaAPI™ (with LabVIEW SDK).
-
Product
XMC Display Control Card
XM61001
-
LinkedHope Intelligent Technologies Co.,Ltd.
XM61001 is an XMC display control card independently developed by Linghao Intelligent®. It is mainly targeted at high-performance embedded graphics image processing and GPU general computing processing (GPGPU) applications.
-
Product
High Voltage 50 Pin D-Type Cables - Connector To Connector For Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a highvoltage 50-pin D-type connector.
-
Product
3U VPX DSP Processor Card
VPX3-450
-
Curtiss-Wright Defense Solutions
Many FPGA processor modules require a separate processor card to control the FPGA module. The VPX3-450 module combines a Xilinx Virtex-5 FPGA and a PowerPC processor on a single module along with a flexible XMC site for bringing different types of IO directly into the FPGA. Therefore, in a single slot, a hybrid solution can be provided.
-
Product
6U Vertical Card
445
-
VECTOR Electronics and Technology, Inc.
Chassis for vertical card installation
-
Product
AC Reference Generators
SR22
-
Computer Conversions Corporation
The SR Series are miniature, low cost AC reference generators designed to supply 26 or 115 volt excitation to synchros or resolvers in military and industrial control applications. They accept +/-15V DC and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6”x3.1”x1”H
-
Product
Interface
RPCC-D1553
Interface
This dual channel card is RoHS-compliant and is a direct drop-in replacement for the PCC-D1553 card which it replaces. The RPCC-D1553 comes with all necessary cables for operation. Cables designed for the PCC-1553 card will not work with the RPCC-D1553 card. The RPCC-D1553 provides 1 or 2 channels integrated with powerful API software providing instant access to all MIL-STD-1553 databus functionality and data.
-
Product
5-slot ATX-supported 2U Butterfly PICMG 1.3 Bus Passive Backplane
FAB205
-
The FAB205 features a PICMG 1.3 CPU card slot, five 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. The FAB205 is optimized to support AXIOMTEK's PICMG 1.3 system host boards, the SHB100 and SHB110, which are built around the PICMG 1.3 form factor. The FAB205 is compatible with the AX61220/AX61222 chassis.
-
Product
19" Accessories
-
Elma’s accessories for rackmount enclosures address virtually every configuration imaginable: From the horizontal card adapter kits to fan and keyboard trays, subrack handles, aluminum front panels and telescoping rails. Furthermore, Elma supplies also 19” cassettes, ventilation solutions as well as a wide range of ejector handles, feet and extrusions according to IEC, IEEE or AdvancedTCA.
-
Product
Mini-ITX SBC With LGA1151 9th/8th Gen Intel® Core™ I7/i5/i3 Processor, Dual DisplayPort++, HDMI, LVDS, USB 3.0, MSATA, M.2 And Dual GbE LAN
MANO520
-
The MANO520 is powered by the LGA1151 socket 9th/8th generation Intel® Core™ i7/i5/i3 (code name: Coffee Lake), Intel® Pentium® Gold or Intel® Celeron® processor with the Intel® Q310 chipset (Intel® Q370 optional). The Intel® Coffee Lake-based MANO520 is specifically designed for performance-demanding applications with its excellent reliability as well as communication and real-time computing capabilities. The MANO520 supports two 260-pin DDR4-2666/2400 SO-DIMM sockets for up to 32GB of memory. Also, the mini-ITX motherboard features three SATA-600 connectors and one mSATA for additional storage. It is equipped with one full-size PCI Express Mini Card, one PCIe x16 and one M.2 Key E slots for wireless devices such as Wi-Fi, Bluetooth, and 3G/LTE. Moreover, the mini-ITX form factor single board computer features an ATX connector with AT mode auto power function.
-
Product
Boards
MIL-STD-1760
-
The MIL-STD-1760 interface card is compatible with all common variations of MIL-STD-1760 and provides a wide range of features normally found only on full size testers. The cards can operate simultaneously as a Bus Controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. The card supports Checksum, SRQ bit and Header Words as well as error injection and error detection.
-
Product
ATX Motherboard With LGA1151 Socket 8th Gen Intel® Core™ Processor, Intel® Q370, USB 3.1 Gen2, SATA 3.0, Dual LAN, VGA, DisplayPort, DVI-D, And HDMI
IMB520
-
The IMB520 is powered by the LGA1151 socket 8th generation Intel® Core™ i7/i5/i3, Pentium® or Celeron® processor (code name: Coffee Lake) with the Intel® Q370 chipset. The ATX motherboard supports four 288-pin DDR4-2666/2400 DIMMs with up to 64GB of system memory. The Intel® Coffee Lake-based IMB520 is a performance-driven motherboard that is expandable, feature-rich and versatile to help facilitate quick deployment. The brand new IMB520 is an ideal solution for automation, transportation, retail, medical and other Industrial IoT-related applications. The IMB520 provides one PCIe x16 slot, four PCIe x4 slots, one PCIe x1 slot and one PCI slot for frame grabbers, motion control cards and edge-based data acquisition cards, making it an ideal solution for machine vision and industrial automation application. It also has two USB 3.1 Gen 2 and four USB 3.1 Gen 1 ports for faster data transfer. In addition, the industrial-grade ATX motherboard is integrated with the Intel® HD Graphics for superb visual performance. Up to three independent displays are available from DisplayPort, DVI-D, HDMI, and VGA.
-
Product
Temperature Loop Control Setup
ULP-27
-
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Temperature Control Loop Setup is basically a PC based PID controller setup used for closed loop and open loop analysis of temperature process system. The setup comprises of RTD temperature Sensor. The water flows through the Rotameter and Process tank to which a heating coil is fitted. The heater is controlled by a Thirstier drive. The Thirstier drive is connected to PID controller. The manual control valve can control the water flow. The system is mounted on a tabletop model with all necessary Piping. Water at approx. 100 LPH has to be supplied to a system externally. The electronic panel comprises of ADC/DAC card with RS-232 interfaces.
