-
Product
Pump Testing Panels
-
Aarohi Embedded Systems Pvt. Ltd
AAROHI Pump Testing Panels - full load, semi/fully-automatic pump test systems
-
Product
Data Loading Products
-
TechSAT's data loading products are available to support all standard ARINC data loading protocols: ARINC 615/615A/826/844 for ARINC 429 and Ethernet based data loading. For next generation aircraft, TechSAT's data loading solutions bring portability to data loading over the new generation of avionics bus and network types: AFDX®/ARINC 664, Avionic & Deterministic Ethernet, TTP, and ARINC 825/CAN
-
Product
AC & DC Electronic Load
3270 Series （350V,1875W~22500W）
-
3270 Series is suitable for the step, square and sine wave of the AC Power device test, especially for the uninterruptible power supply UPS, Inverter, fuses, circuit breakers, power regulator AVR, battery, AC / DC power supply / components ... and so on, absolutely is the best test solution in the market.
-
Product
OTP-Based Test System
Test System
Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and voltage ranges cover the test of frequent DUT operating parameters. Time-dependent voltage or current signals can be stimulated by an arbitrary generator with power amplifier. General measurements such as current, voltage, frequency, resistance can be carried out flexibly at various test points using the matrix concept. An oscilloscope with RF multiplexer is available for high-frequency measurements such as residual ripple, switching processes, etc.
-
Product
I-V Measurement Systems
-
The I-V Curve Data Acquisition includes a fixture for holding cells for testing (see Figure 1 below). This fixture can accommodate cells from small to up to 100 mm x 100 mm. Adjustable cell stops, in the X & Y-axis, are provided to consistently locate the cells for testing. Two micro-manipulators are provided as shown in Figure 1. Each micro-manipulator has two spring loaded contacts to allow 4-wire measurement even for cells that have top contacts only. Two back-side voltage contacts are embedded in the Plate (galvanically isolated from the Plate) and make good electrical contact when the cell is held down by vacuum to the plate. All voltage and current probes are gold-plated. The cell is held down with vacuum during testing (built-in vacuum pump).
-
Product
ESU Analyzer
ESU-2050
-
The BC Biomedical ESU-2050 ESU Analyzer is the first instrument of its kind on the market. Designed through extensive collaboration with several of the world's leading electrosurgery generator manufacturers. It is the only ESU Analyzer on today's market with a 1% reading level of accuracy. Calibration quality analyzer; uses external precision non-inductive test loads and wide band current transformer.
-
Product
VOC FIXTURE OVER CLAMP ASSEMBLY'S
-
Test-X VOC Series overclamps are used for testing bare or loaded printed circuit boards with open vias and to minimize board flex.The VOC Series overclamp comes with adjustable delrin pressure fingers, anti-rotating hex nuts, hinge and latching assemblies, mounting instructions and hardware.The VOC Series will accomodate fixtures with dress frames or newer style fixtures using full-size top plates.
-
Product
sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
781028-01
Strain/Bridge Input Module
Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.
-
Product
High-Power PXI Switch Matrix Modules
-
These high-power PXI switch matrix modules provide higher current and power ratings than the high-density switch versions. These modules are designed for the switching of AC or DC loads or for controlling large relay or solenoid systems. The solid state relay matrices occupy two PXI slots and are suitable for automotive and aerospace test applications.
-
Product
DC Hipot and Megohmmeter
PTS Series
-
The PTS Series can perform high voltage DC hipot/proof and current leakage testing as well as resistance measurement testing. Most models offer a high output current for quicker charging of capacitive loads like cables. Like all HVI portable test equipment, the PTS Series is designed to withstand the rigors of field use.
-
Product
ARC Fusion Splicer
FBT-19S
-
Shanghai Fibretool Technology Co.,Ltd.
FBT-19S Optical Fiber Fusion Splicer is small size optical fiber fusions splicer, mainly used for fusion and protection of common communications fibers. The rich functionality and ultra-low splice loss make the splicer adaptive to fiber splicing in various environments. It is featured with small size, light weight, high reliability, greater environmental adaptability, dust-resistant, water-resistant and shock-resistant. Multiple fusion modes and heating modes are available to meet diversified customers’ demands. Fiber loading becomes more convenient and accurate thanks to the ceramic V-groove of high precision, which is easy for clean and maintenance. The splicer is capable of dual-directional fusion. The monitor is a touch screen delivers fresh designed graphical interfaces, which are simple for operation. The modular pluggable lithium-ion battery of large-capacity ensures long-time field operations. The auto environment compensation system greatly improves adaptability of the splicer to hostile environments, so that low-loss splice can be remained consistent in various environments.
-
Product
1×6 Video Distribution Amplifier
VDA206 S-Video
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
779521-01
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
T3SP Time Domain Reflectometers
T3SP Series
-
Teledyne Test Tools T3SP15D stimulates the DUT with true differential signals. The T3SP15D offers fast rise times of 35 ps for spatial impedance resolution (in FR4) of 3 mm, at DUT lengths up to 40 meters and TDR repetition rates up to 10 MHz and uses the same open short load thru (OSLT) calibration standards as vector network analyzers. With their small form factors, light weight, and optional internal batteries, the instruments go anywhere in test labs or in the field at an affordable price.
-
Product
Single Point Load Cells
-
These have a range of different platform sizes and are suitable for different applications including bench scales, counting scales and other applications in many industries. Click the links below to find out more about each product and to view specific data sheets.
-
Product
Pressure, Strain And Shock Data Loggers
-
Dataloggers for pressure, bridge input for strain or load measurement and also tri-axial shock dataloggers with built in accelerometers.
-
Product
Brick Power Module Test
-
Modern servers, workstations, and telecom equipment often use an Intermediate Bus Architecture (IBA) powered by isolated DC/DC converters known as "brick" modules. These brick converters step down the input voltage to a lower DC bus voltage, enabling designers to implement efficient, high-density, non-isolated Point-of-Load (POL) regulators that power components such as microprocessors, FPGAs, and ASICs on system boards. With smaller voltage step-down ratios now common, designing POL regulators has become more straightforward. Brick modules are so named for their standard physical formats (1/4 Brick, 1/2 Brick, Full Brick, etc.), making them easy to integrate and replace.
-
Product
PXIe-4137, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit
783761-02
Source Measure Unit
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4137 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology helps you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4137 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers
-
Product
1008W - Single Output
iQK Series
-
*Standard Quarter Brick Footprint*48-56 Vdc Input*11.2 Vdc Output*707 Vdc Isolation*Baseplate Cooled*97% Typical Efficiency*Droop Load Share Option
-
Product
Handheld Raman Spectrometer
NanoRam® – BWT-840000341
-
The NanoRam is a state-of-the-art handheld Raman instrument for nondestructive identification and verification of materials such as APIs, excipients, intermediates, & finished products. Compact and agile, the NanoRam can be used by non-technical users to rapidly identify samples in the lab, warehouse, loading dock or field, helping to eliminate quarantine areas and expedite materials through the manufacturing lifecycle. Utilizing Raman technology, non-contact analysis can be performed through transparent containers, all while maintaining the volume and integrity of the sample.
-
Product
Rotary Table Handler
6000 Series Rotary Handler
-
Rotary table handlers are an excellent choice for PCBA or product – level test, programming, part marking, automatic part rejecting, and vision inspection in order to satisfy manufacturing applications that require high throughput. Rotary table based systems used in production can also help reduce the impact of load and unload times for the operator, because the device-under-test (DUT) automatically moves to the next cell within the station as each DUT is loaded. Circuit Check’s 6000 series handlers are modular, scalable and flexible, supporting high-mix and high-volume production needs. A common application example is to configure a 6000 series as a rotary station to perform simultaneous PCBA bar code scanning, testing, programming and marking, in a pipe-line process which improves throughput requirements. The 6000 series handlers leverage Circuit Check’s unique quick-change fixture drop-in technologies to allow for station modularity and scalability. Production line flexibility is achieved because the 6000 series handler is software and hardware agnostic, enabling adaptability to a variety of applications, and is limited only by the number of stations.
-
Product
Programmable Single Channel DC Electronic Load, 150V/30A/300W
T3EL150303P
-
Programmable Single Channel DC Electronic Load, 150V/30A/300W.
-
Product
Digital Roller Brake Tester for Cars and Vans up to 3.5 T Axle Load with 2 x 3 kW Drive Motors and Max. Track Width of 2,500mm
C_MBT C 3.5 W250 | VP 210153
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 3.5 t axle load with 2 x 3 kW drive motors and a max. track width of 2,500 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes for larger vehicles such as SUVs, off-roaders or vans.
-
Product
Linear Actuators
Electrak LA14
-
Electrak LA14 is based on the Electrak 10 design, which incorporates a screw drive system for applications requiring maximum load capacity, robust performance, and long life. Its additional benefits offer the a built-in anti rotation mechanism and an aluminium cover tube. The aluminium cover tube has T-slots that can be used for mounting and also accepts magnetic sensor to be fitted along two sides of the tube.
-
Product
ESS Performance Test System
Test System
The Energy Storage System (ESS) Performance Test System is used to evaluate, test, and certify the performance of energy storage systems up to 2MW. The system is a configurable platform with over 200 channels of simultaneously measured AC and DC voltages and currents, environmental temperatures, airflow, and communications. Intuitive software provides real-time monitoring and analysis of power, energy and efficiency to adhere with industry standards. The test system interfaces hardware such as load banks, and controls the ESS to simulate utility applications such as peak shaving and frequency regulation.
-
Product
Cold Bend Testing Machine
QualiBend Series
-
The Cold Bend Testing Machine - QualiBend series are used for bending of metallic materials such as metal rods, planks and steel screw threads. The machines operate with a hydraulic loading system to adjust the distance of the cold-bending press roll to drive the rod in both directions making the cold bending press roll forward and back.
-
Product
3U VPX 1 Slot P&G w VITA 67.3D connector in J2
101V301P05-9003R
-
Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
-
Product
PXI 5A Mux 2-Bank 24-Ch Isolated COM
40-651-012
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
Soft Front Panel for NI RF Generators
NI RFSG Soft Front Panel
-
The NI RFSG Soft Front Panel helps you quickly generate RF continuous wave (CW) or modulated signals. It works with the NI PXIe-5644R/5645R/5646R vector signal transceivers (VSTs) and NI 567x vector signal generators (VSGs). You can open multiple instances for multiple instruments in a system. In addition, you can load I/Q waveforms, save and recall setups, preview data that is loaded onto the VSG, and sweep levels or frequencies using RF list mode. The soft front panel also features built-in modulation schemes such as AM, FM, and PM.
-
Product
20V/30A/300W DC Programmable Electronic Load
TOB-IT8512
-
Xiamen Tob New Energy Technology Co., Ltd
IT8512 120V/30A/300W DC Programmable Electronic Load for Battery and Power Supply TestHigh performance and affordable single channel DC electronic load. TOB-IT8512 DC electronic loads provide you with the flexibility to test a wide range of applications from power supply, charger to battery. The high resolution voltage(1mV), current(0.1mA) measurement system provides both accuracy and convenience, and eliminates the need for a DMM, external shunts and wiring.
