Modules
See Also: Contacts, Boards, ITA, Cable Assembly, Cards
-
Product
RF Mixers
-
An RF mixer is a three-port passive or active device that can modulate or demodulate a signal.
-
Product
Automatic Calibration Module
ACM2509
-
ACM2509 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 9 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process. Automating the calibration routine also reduces wear and tear on the analyzer and RF cables. To perform full two-port calibration, each end of the ACM need only be connected to the analyzer once, as opposed to seven connections with a traditional calibration. The ACM also contains a factory characterized 20dB in-line attenuator which acts as a simulated device under test (DUT). The confidence check feature loads the factory stored DUT into memory so proper calibration can be verified.
-
Product
PXI Multiplexer Dual 16 Ch 2 Pole
40-630-022-D/16/2
-
This series of general purpose multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 68-pin connector. Available reed relay formats are 1-pole, 2-pole and 1-pole screened.
-
Product
4-CH RTD Thermal Input EtherCAT Module
EPS-3504
-
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
PXI/PXIe 15W Programmable Resistor Module
42-254-012
-
The 40-254-012 (PXI) and 42-254-012 (PXIe) are programmable resistor modules with 2 channels which can be set between 1Ω and 120Ω with 0.5Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
50 Ohm SMA to SMA Cable Assembly
40-977-521-1m
-
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-133-HI
-
The 40-230-133-HI (PXI) and 42-230-133-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 52.4kΩ with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
ITC Style VXI Module Shield Kits
-
* Box design for C-size ITC style PC Boards with 11 slots on their sides.* Pre-machined flat front panel with ejector handle cutouts.* Side shields include 0.375 inch wide vent slot on top and bottom sides for maximum cooling.* Shroudless design fits all VXI chassis.* Each kit includes side shields, front panel, ejector handles, two ejector face places with VXI and ICS logos, all hardware and assembly instructions.* Complimentary layout support includes PCB design template and CAD layout files.
-
Product
InfiniiVision Oscilloscopes
3000T X-Series
-
100 MHz - 1 GHz, DSO and MSO models Speed testing with simplified operation and documentation enabled by the 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone Touch Triggering See the most signal detail with 1,000,000 wfms/s update rateQuickly modulate and characterize signals with built-in WaveGen 20 MHz ARB, 3-digit voltmeter and 8-digit frequency counter & totalizer options Decode serial busses faster with hardware-based serial analysis options Protect your investment with full upgradeability
-
Product
NI-9223, ±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
781398-01
-
±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9223 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9223 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9223: either four, 2‑position screw terminal connectors or four BNC connectors.
-
Product
32-CH I/O Terminal Base
HSL-TB32-M-DIN
-
*Field I/O wiring connection for HSL I/O modules*Spring terminal for easy field wiring*Power and ground included for each signal channel*Interlocking design for rugged installation*Power LED indicator*DIN rail mounting
-
Product
Ethernet Connector Modules
-
With an extensive line of high-quality ethernet connector modules in our product lineup, Pulse Electronics Networking BU can easily supply the parts you need to develop your next ethernet product.
-
Product
Proprietary LPWAN/SUB-G Wireless I/O Module
-
WISE-4210 utilizse proprietary LPWAN (low-power wide-area network) wireless interface, which provides better connection compared with 2.4G Wi-Fi.
-
Product
PXI 8 Slot BRIC 88x16 2-pole (8 sub-cards)
40-562A-122-88X16
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 4-Slot BRIC Matrix, 264x4 2-Pole (6 sub-cards)
40-562B-022-264X4
-
The 40-562B-022-264X4 is a high density BRIC4 matrix module with a size of 264x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXIe High Performance System Module: Dual Port (x16), Gen 3
M9023A
-
The M9023A is a PXIe System Module and is installed in the system slot of a PXIe chassis. When combined with an appropriate host adapter, it will provide a high data BW connection between the host PC and the chassis. The M9023A has a flexible configuration capability. Each card has two Gen 3 x8 PCIe cable links capable of achieving speeds up to 8 GB/s on each port. These two ports can be combined into a single x16 cable link providing a speed of up to 16 GB/s. This means a data-intensive system can be built using high-performance desktop or rack-mounted computers.
-
Product
ONU Two Output RFTV Optical Receive Module
M9226
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai M9226 optical receiving module is designed for ONU optical fiber network unit. This series of product with perfect detect and remote shutting off function adopts high sensitivity receiving tube and Huatai special low noise matching circuit. It is a kind of high index, low power consumption and high cost performance RFTV optical receiving unit.
-
Product
Single 12x12 1-Pole High-Density PXI Matrix Module
40-520-102
-
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
160-Pin DIN41612 Connector, Right Angle PCB Mount, Female
40-963-160-RF
-
Accessory allows a user to create their own PCB based termination solution. Female versions are suited to direct connection to a Pickering Switching Module while male versions can be used to interface to a female cable assembly termination.
-
Product
High Voltage 50 Pin D-Type Cables - Connector To Connector For Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a highvoltage 50-pin D-type connector.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP10T, 18 GHz, 50 Ω, SMA, Failsafe
40-788-121
-
The 40-788-121 (PXI) and 42-788-121 (PXIe) are single failsafe SP10T 18 GHz unterminated microwave multiplexers. The 40/42-788 range of multiplexers are available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel. Remote versions are also available which can support one or two multiplexers in a dual slot module.
-
Product
Cable/terrestrial Modulator For USB-2
DTU-215
-
The DTU-215 is a portable modulator for terrestrial and cable standards. By it's USB powered design and a comprehensive channel-simulator, including AWGN and Multipath echo, it is a true fully-featured and easy-to-use multi-standard modulator for demonstrations and R&D.
-
Product
LXI High Voltage Switching Multiplexer Plugin Module
65-231-906-HI
-
The 65-231-906-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
COM Express Compact Size Type 6 Module with 11th Gen Intel® Core™ and Celeron® Processors (formerly codename: Tiger Lake-UP3)
cExpress-TL
-
ADLINK cExpress-TL,based on the 11th Gen Intel® Core™ i7/i5/i3 and Celeron™ processor, is the first COM Express module to support PCI Express Gen 4 at 16 GT/s, effectively doubling the bandwidth of previous generations. Additionally if features support for 2.5GbE Ethernet, leveraging existing Cat5e cable infrastructure being used for 1GbE Ethernet, it supports four USB 3.2 ports with transfer rates up to 10Gb/s. The modules have a configurable power range of 15 to 28 watts, which suits them for fanless space-constrained embedded applications. Typical industries in need of such high-performance/low-power characteristics are transport, medical, industrial automation and control, edge controllers, robotics and multi-camera-based AI. cExpress-TL features the Intel® Iris® Xe, a new graphics core, and supporting AVX-512 Vector Neural Net Instructions (VNNI) can significantly improve the number of elements processed per cycle, providing AI inferencing performance that is up to 3x that of previously available from non-VNNI platforms. Intel® Iris® Xe provides 96 execution units and is able to be configured to support two 8K independent displays or four 4K independent display (HDMI/DP/eDP). Additional support includes In-Band ECC (IBECC), providing ECC level error correction on DDR4 SODIMM memories for mission critical or rugged applications.
-
Product
3U cPCI Intel SBC
75INT2
-
NAI’s 75INT2 is a 3U cPCI Intel® Core™ i7-based, Single Board Computer (SBC) that can be configured with up to two intelligent function modules and delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems.NAI's Intel® Core™ i7 SBCs in the 3U cPCI form factor offer improved processor performance and better security, targeted at military and defense applications such as manned and un-manned air and ground vehicles, and in more sophisticated digital signal processing applications such as intelligence, surveillance, reconnaissance, radar and sonar.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber, ST Connectors, With Interlock
42-850A-514-M50-HI
-
The 40/42-850A-514-M50-HI is a PXI/PXIe 4-channel multiplexer with ST connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
ITA, ICon XL, 2 Module, Extra-Large Backshell, EMI
410123232
-
The iCon XL offers an extra-large u-shaped cable clamp that can hold cable bundles with an oblong bushing effective diameter of 1.95" and offers a cable bend radius of 1". A slide-off backshell allows easy access to wiring for maintenance and probing. The iCon XL also offers EMI shielding.
-
Product
LXI Scalable Matrix - 2Amp 10x20 Configurable Matrix Plugin Module
65-219-206
-
Matrices are created by populating the 65-200 scalable matrix chassis with plug-in modules that provide access to the X axis on 15-pin D-type connectors and the Y axis on 50-pin D-type connectors. The chassis is capable of supporting matrices with a Y axis size of 20 or 40 and X axis sizes up to 60 in increments of 10. Users can specify as many or as few plugin modules as they require and can field upgrade the chassis to extend the matrix size.
-
Product
PXI 2A Multiplexer, 4-Bank, 8-Channel, 4-Pole
40-614B-008
-
This 4-bank, 8-channel, 4-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
2-6GHz Ultra Compact Digital Receiver
QR037
-
The Teledyne Defence & Space (TDS) Single Channel High Performance Receiver provides a new approach for ESM / ELINT applications, incorporating patented features offering wide band synthesized capability from 500MHz to 18GHz, with frequency extensions available up to 40GHz.TDS’s new QR037 digital receiver module combines high dynamic range RF down conversion and LO generation with digitisation and signal processing capabilities to provide a compact solution for a number of ELINT/COMINT and ESM applications.Excellent dynamic range and linearity is achieved through a combination of RF and digital down conversion stages coupled with high performance pre-selection and IF filtering.
