Modules
See Also: Contacts, Boards, ITA, Cable Assembly, Cards
-
Product
PXI Single 18 Channel MUX, BNC Connectors
40-735-902-S3
-
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-115
-
The 40-297A-115 (PXI) and the 42-297A-115 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 920 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
25 Pin D-Type Connectors For Pickering Products
-
The connectors below are suitable to use with Pickering cards and modules that utilize a 25-pin D-type connector.
-
Product
PXI 2A Multiplexer, 8-Bank, 8-Channel 2-Pole
40-614-004
-
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass
40-860A-122
-
The 40/42-860A-122 is a PXI/PXIe dual insert/bypass switch with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
Real-Time Clock & Interrupt Module
RCIM IV
-
The Real-Time Clock & Interrupt Module (RCIM IV) is a multifunction card designed for time-critical applications on Concurrent Real-Time’s iHawk™ multiprocessing systems. The RCIM provides key functionality for single system as well as multiple system applications.
-
Product
Electromagnetic Immunity Scanner
SmartScan 350
-
Reproducing similar soft or hard failure to the gun test - Flexible automatic failure detection module - Susceptibility map generation- Automatic report generation- Flexible scan area editor (SAE)- Flexible display (3D, histogram)- Matlab support- Expandability (EMI scan, phase measurement, NFFF transformation)- Custom design probes
-
Product
Qseven Module With Intel® Atom® X5 And X7 Processors
Q7M310
-
*Intel® Atom® x5 and x7 processor (Apollo Lake)*8GB DDR3L memory onboard*4 lanes of PCI Express slot*2 SATA-600*2 USB 3.0 and 4 USB 2.0
-
Product
Solar Array Simulator Auto-Ranging Module 0-160V, 0-10A, 1kW
MP4361A
-
The Keysight MP4361A is a 1000 W solar array simulator DC power module that simulates the output characteristics of a solar array. The MP4361A is primarily a current source with very low output capacitance. It offers fast I-V curve changes allowing you to accurately simulate the output of different solar arrays under various environmental conditions (ex. temperature, age, eclipse, spin, etc.).
-
Product
Keysight 40-Channel Armature Multiplexer for 34980A
34921A
-
The Keysight 34921A module for the 34980A Multifunction Switch/Measure Unit is the most versatile multiplexer for general purpose scanning. It has low thermal offset characteristics and a built-in thermocouple reference on the terminal block, making it ideal for temperature measurements directly to the internal DMM. The dense, multi-function switching with 100 channel/second scan rates addresses a broad spectrum of data acquisition applications.
-
Product
PCI 8x9 RF Coaxial Matrix Card 50Ω SMB
50-725A-511
-
The 50-725A is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz. The 50-725A is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
47~2600MHz Satellite TV & Digital TV 1550nm Externally Modulated Optical Transmitter
HES-26D
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HES-26D series 1550nm external modulation optical transmitter can transmit 47~2600MHz analogue signal and digital signal via one single fiber by frequency division multiplexing. It is compatible with any FTTx PON technology, and provides a complete set of high quality low cost fiber trunk transmission and fiber to the building (FTTB), fiber to the house (FTTH) solution for the direct broadcast satellite TV (DBS) and cable analogue TV (CATV) fusion.
-
Product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-041
-
The 40-297A-041 (PXI) and the 42-297A-041 (PXIe) are 6-channel programmable resistors with a range of 2.5 Ω to 201 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI 8 Slot BRIC 132x8 2A 1-Pole Matrix
40-567-103
-
The 40-567 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-567 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
128 Channel Digital I/O Modular PXI Card
GX5733 Series
-
The GX5733 is a 3U modular digital I/O card that offers up to 128 I/O channels. Designed for ATE, data acquisition, or process control systems where a large number of discrete I/O channels are required, the GX5733 offers the highest channel density and flexibility in the industry for a single-slot, 3U PXI plug-in board. 96 channels support TTL levels and an additional 32 I/O channels can be customized by installing one of Marvin Test Solutions' GX57xx series I/O modules. Alternatively, the remaining port can be configured to support 32 TTL channels.
-
Product
Wideband Active Load Pull Export Control
S94573B
-
The software enables power amplifier distortion measurements under varying load conditions that are controlled across the entire modulation bandwidth. When design verification and robustness evaluation require testing the device away from the optimum loading condition, this application provides powerful insight into device performance and degradation.
-
Product
0.3Hz-6MHz Amplitude Display Functional Generator
MFG-8306
-
Features:*Max. frequency up to 15MHz*Single-chip function generating module provides high stability and low distortion waveforms*5 digit frequency display, 3 digit amplitude display.*Built-in frequency meter for testing external signal up to 20MHz*Linear and Logarithmic sweep function.*AM/FM function optional(Models with suffix “A”)*5W Power Output function optional(Models with suffix “W”)
-
Product
Module Spectrum
nRF52810 Series
-
Nordic nRF52810 solutioin features an Arm Cortex-M4 processor with 192 KB Flash and 24 KB RAM with 32 GPIO available. Supports SPI, UART, I2C, PWM interfaces with both Chip Antenna and PCB Antenna option for selection.
-
Product
PXI/PXIe High Density Electro-mechanical Relay Module, 50xSPST, Normally Open
42-145A-001
-
The 40-145A-001 (PXI) and 42-145A-001 (PXIe) 50xSPST relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
Product
MO-300 MSATA Module
SQF-SMS 630
-
SQFlash mSATA 630, SATA Gen. 3 (6.0Gbps) Compliant with SATA III and SATA v 3.0 standard. Supports 72 bit ECC correct per 1K Byte data. Support hardware write protect. Supports Fragment Writing Technology and Flush Manager.
-
Product
PXI Prototyping Module, 2-Slot, 9-Pin D-Type
40-225A-702
-
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI SPST Switch: 100-ch, 100Vrms/1A, Reed Relays
M9133A
-
The M9133A is a high-density, general purpose switch with 100 independent, single-pole, single-throw (Form A) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids. The high-speed, long-life reed relays can handle 100Vrms and 1A, with up to 25W power. Choose from the durable connector block or the standard cable connections.
-
Product
Modular Tester For Final Test Of LRU’s
FLEX 50
-
The FLEX 50 is designed for customers that prefer a traditional 19” rack format system. The system can be configured with a range of analogue, digital, mixed-signal, and avionics test modules.
-
Product
USB Modular Products Chassis
U2781A
-
The Keysight U2781A USB modular instrument chassis is a high-performance 4U high chassis that comes with a 200 W universal AC power supply and a built-in protection circuit. This portable chassis can house up to six Keysight USB modular products. The U2781A targets a wide range of applications in both industrial and scientific environments in the research and development (R&D), design-validation, and manufacturing fields. The primary advantage of this chassis is its synchronization capability between modules. This can help you to lower your cost of testing and accelerate your test system integration and development.
-
Product
50 Ohm SMB to BNC Adaptor Assembly
40-978-501-0.1m
-
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
NI-9215, cDAQ-9171, and NI-9981 USB Voltage Measurement Bundle
865684-01
-
NI-9215, cDAQ-9171, and NI-9981 USB Voltage Measurement Bundle - The USB Voltage Measurement Bundle with NI-9215, cDAQ-9171, and NI-9981 includes the NI-9215 C Series Voltage Input Module and the cDAQ-9171 CompactDAQ Chassis for voltage measurements. This bundle also includes the NI-9981 Connector for strain relief and operator protection from high-voltage signals. The included NI-9215 provides noise immunity, a high common-mode voltage range, NIST-traceable calibration, differential analog inputs, and four channels.
-
Product
FaithTech Regenerative High-power Programmable DC Load
FTR9000 Series
-
Shenzhen FaithTech Technology Co., Ltd.
FTR9000 series is a regenerative programmable DC electronic load. It not only has the function of traditional consumable load, but also cleanly feeds the energy consumed by traditional load back to the power grid to achieve the purpose of energy conservation. It can be widely used in new energy equipment testing, lithium ion, fuel and other battery discharge testing, automatic testing system, AC/DC, DC/DC and other one-way module product testing and aging. The product is equipped with rich communication, programming interfaces, color screens and a variety of text menu interfaces, which is easy to operate and intuitive. It is a common equipment in the power electronics, new energy, sensors, motor drives, system integration and other industries.
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-023
-
The 40-297A-023 (PXI) and the 42-297A-023 (PXIe) are 9-channel programmable resistors with a range of 1.5 Ω to 3.55 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber
40-850A-514-HI
-
The 40/42-850A-514-HI is a PXI/PXIe 4-channel multiplexer with ST connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
4-Channel 200 MHz A/D with DDC, Virtex-7 FPGA - 3U VPX
Model 52761
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four 200 MHz 16-bit A/Ds- Four multiband DDCs- Multiboard programmable beamformer- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
