DC DC Converters
-
product
DC Energy Meter
Multiple channels can be measured by a single meter, EN2450N & EN2450DDifferential current input for all the current channelsProgrammable shunt secondary 50mV to 100mVProgrammable CT Primary for all channels up to 200A - for Hall Effect CTData logging for parameters such as Energy, Load hours and Ampere hoursEasy installation,Compact size, weight and simple wiring
-
product
Single Channel Programmable DC Power Supply
IT6800A/B Series
IT6800 single channel programmable DC power supply (180W-216W) with resolution 1mV/0.1mA, users can adjust the voltage/current stepping by pressing the left and right keys to moving the cursor and programs by the front panel. OVP/OTP protection. IT6800 supports timer function and their built-in RS232 and USB communication interfaces offer you a convinience testing experience.
-
product
AC & DC Electronic Loads
The Adaptive Power Systems Electronic Loads cover a wide range of power levels, voltage and current profiles and feature sets.Supported voltages range up to 1250Vdc or 350Vrms AC. From bench to system and DC or AC requirements, we can more than likely offer you the optimal programmable load to meet your needs.
-
product
Capacitor for DC Filtering
FIL1
Lifasa - International Capacitors, SA
FIL condensers are specially designed for use in direct current sources and their functions are to filter the alternating output ripple and protect the line from instantaneous peaks and surges of tension.
-
product
Low PIM Coaxial Switch, DC to 20 GHz, SP6T
87106Q
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87106Q is a low PIM SP6T coaxial switch, operating from DC to 20 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
Linear DC Power Supply
MPS-3600LP Series
MPS-3600LP Series is the high-quality programmable DC power supply of new generation, and this series of products can be equipped with communication interface. MPS-3600LP Series power supply has the characteristics of both desktop type and system type, and can be freely matched with other instruments to integrate into the test system and special functions so as to meet measurement demands on different occasions, and the program can be edited through panel keyboard to bring great convergence to users. It is an alternative product of the ordinary programmable power supply, and has advantage of high cost performance.
-
product
Bipolar DC Power Supply / Battery Simulator
IT6400 Series
The unique bipolar voltage/current output makes IT6400 series can be used as a bipolar power source or a bipolar electronic load. The battery simulating function is especially applicable for development and high speed production testing of portable, battery-operated products.
-
product
AC & DC Aging Test Equipment for Arrester Valve Plate
Shanghai Guantu Technology Co., Ltd.
The arrester is usually connected between the live wire and the ground, and is connected in parallel with the protected equipment. When the overvoltage value reaches the specified operating voltage, the arrester will act immediately, flow the charge, limit the overvoltage amplitude, and protect the insulation of the equipment; when the voltage value is normal, the arrester will quickly return to its original state to ensure the normal power supply of the system.
-
product
Multiport Coaxial Switch, DC to 20 GHz, SP6T
87106B
The Keysight 87106B multiport switch improves insertion loss repeatability and isolation, which is necessary for higher performance test systems. The repeatability and reliability of this switch is vital to ATS measurement accuracy and can cut the cost of ownership by reducing calibration cycles and increasing test system up time. The Keysight 87106B terminated multiport switch provides the long life and reliability required for automated test and measurement, signal monitoring, and routing applications. Highly repeatable switching capability is made possible through Keysight's rigorous design and tight manufacturing specifications. Low insertion loss repeatability reduces sources of random errors in the measurement path, which improves measurement accuracy.
-
product
DC Blocking L-Band Splitter Combiner
PD5980
INSTOCK Wireless Components, Inc
PD5980 is an IP67 outdoor, weather resistant, DC blocking, eight way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5980 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 8 way power divider input rating tables for additional power handling info.
-
product
Microvolt DC Volt Meter
QA350
The QA350 relies on a built-in reference to calibrate the ratio between the hi and low ranges. If you have a preferred lab reference, you may use that it to improve the QA350 accuracy beyond the indicated +/- 400 PPM. For example, various vendors on eBay can provide calibrated +/-30 PPM 5 or 10V voltage references that can be used to set the ultimate accuracy of the QA350 to under 50 PPM at room temperature.
-
product
DC Power Analyzer, Modular, 600 W, 4 Slots
N6705C
The N6705C DC Power Analyzer provides unrivaled productivity gains for sourcing and measuring DC voltage and current into the DUT by integrating up to 4 advanced power supplies with DMM, Scope, Arb, and Data Logger features. The N6705C eliminates the need to gather multiple pieces of equipment and create complex test setups including transducers (such as current probes and shunts) to measure current into your DUT. The DC Power Analyzer also eliminates the need to develop and debug programs to control a collection of instruments and take useful measurements because all functions and measurements are available at the front panel. For even greater control and analysis functions, the DC Power Analyzer can be used with the 14585A Control and Analysis Software. When automated bench setups are required, the N6705C is fully programmable over GPIB, USB, LAN and is LXI Compliant. 14585A Control and Analysis Software
-
product
L Band Splitter, DC Block All Ports
PD5142
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) Low PIM
-
product
Power Splitter, DC to 26.5 GHz
11667B
The Keysight 11667B power splitter is recommended when making wideband ratio measurements using a Keysight 8757 scalar network analyzer. This two-resistor type power splitter provides excellent output SWR at the auxilliary arm when used for source leveling or ratio measurement applications. The tracking between output arms over a frequency range from dc to 26.5 GHz allows wideband measurements to be made with a minimum of uncertainty.
-
product
Programmable Linear DC Power Supply 3 Outputs, 0-30V/0-6A/1.8V/2.5V/3.3V/5V;5A
T3PS30063P
Programmable Linear DC Power Supply 3 Outputs, 0-30V/0-6A/1.8V/2.5V/3.3V/5V;5A.
-
product
AC / DC Sensors For High Voltage Measurements
The Mors Smitt CatEnergy sensor range provide a proven, reliable, accurate and cost-effective solution for rolling stock. Based on its capacity of multi-voltage and current measurements, alone Mors Smitt sensor products could be used as single solution for all function requiring high voltage measurement on existing and new build train.
-
product
DC Clamp Meter
Shenzhen UYIGAO Electronic Technology Co., Ltd
Is used to measure the DC currents.
-
product
Three-Phase Converters
SIRIO 3PH 7 ALFA 3PHSAP
The three-phase converter is an electronic equipment able to vary the RMS value of a sinusoidal voltage by controlling no. 6 controlled, antiparallel-connected conducting diode pairs.Since the wave form is symmetrically split both into positive and negative halfwave, the output voltage average value is not affected and equal to zero. This means that three-phase loads can be fed without gene rating inside the mesh a circulating current with average value other than zero.Moreover, the three-phase converting is obtained with only one control circuit thus ensuring balance between the three linked voltages applied to the load.
-
product
AC / DC - Power Supplies
The spectrum of DC power supplies ranges from simple power adapters with only one output voltage to complex controllable power sources. Power adapters, often also called plug-in mains adapters, are mainly used for small electrical appliances (such as telephones, strings of light, notebooks, etc.) in private households. They are included in the scope of delivery of the product and only serve to supply power with a defined output voltage of 6 V or 12 V, for example. The output power is usually limited to < 200 W due to the simple design.
-
product
Multiport Coaxial Switch, DC to 26.5 GHz, SP4T
87104C
The Keysight 87104C multiport switch improves insertion loss repeatability and isolation, which is necessary for higher performance test systems. The repeatability and reliability of this switch is vital to ATS measurement accuracy and can cut the cost of ownership by reducing calibration cycles and increasing test system up time. The Keysight 87104C terminated multiport switch provides the long life and reliability required for automated test and measurement, signal monitoring, and routing applications. Highly repeatable switching capability is made possible through Keysight's rigorous design and tight manufacturing specifications. Low insertion loss repeatability reduces sources of random errors in the measurement path, which improves measurement accuracy.
-
product
Multiport Electromechanical Coaxial Switch, DC to 40 GHz, SP4T
87104D
The Keysight 87104D multiport switch improves signal accuracy in RF and microwave signal routing and testing applications. This high performance electromechanical switch provides unmatched isolation and a 0.03 dB insertion loss repeatability, which is warranted for the 5-million life cycle of the switch. The 87104D’s low insertion loss repeatability reduces sources of random errors in the measurement path, which improves measurement accuracy. The repeatability and reliability of this switch guarantee measurement accuracy and can cut the cost of ownership by reducing calibration cycles and increasing test system up time. Highly repeatable switching capability is made possible through Keysight's rigorous design and tight manufacturing specifications.
-
product
DC Blocks
The Keysight DC blocks offer a new level of DC blocking with performance specified from 50 kHz all the way up to 67 GHz. Precision coaxial connector interfaces ensure an excellent impedance match across wide bandwidths, and come in a variety of RF connectors to fit your application needs. Two choices of DC Voltage ratings make these suitable for a wide range of applications.
-
product
High Power DC Electronic Load
M97XX series
The new M97XX series programmable DC electronic load is a new generation product designed from Maynuo Electronic Co.,Ltd. Incorporating high-performance chips, the M97XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M97XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications.
-
product
DC Power Module, 20V, 2.5A, 50W
N6733B
This module is used in both the small, multiple output 1U high N6700 Low-Profile Modular Power System (for ATE systems) and the multiple output N6705 DC Power Analyzer (for bench testing). GPIB, LAN, USB, and LXI compliance are standard. Select from more than 20 different DC power modules, ranging in capability from basic to high precision, and in power from 20 - 300 W.
-
product
DC Laboratory Power Supplies
PeakTech Prüf- und Messtechnik GmbH
Ideally suited for teaching aids, schools and universities and offers safe use but also a very good price / performance ratio.
-
product
Wireless Connectivity AC / DC Clamp Meter with 6000 count / NCV / SPT / 600A AC / DC Current
MS-W366D
This is a external wireless connectivity Digital Clamp Meter integrated with AC / DC hall effect sensor / 6000 Count, True RMS, auto and manual measurement.
-
product
Power Amplifier (DC Powered)
RF Lambda’s DC solid state power amplifiers (PA) are used in a variety of applications and offer high output power, wide band operation and good linearity. Hermetically sealed options are available upon request.
-
product
DC Coreless Motor
Adamant Namiki Precision Jewel Co Ltd.
There is a structure in the cage shape by only the copper wire turns around a cylindrical permanent magnet placed inside It is a feature. There There is not an anron core, it does not receive the action of the copper basket type rotor is light, the moment of inertia becomes small, so quick response is possible. A Permanent Magnet, There Is No Cogging, That Is, Rotation Is Smooth, And Vibration And Noise Can Be Reduced. - Since Rare Earth Magnets With High Magnetic Properties Are Used And The Rotor Is Formed Only With Coils, The Motor Itself Can Be Made smaller and lighter.
-
product
DC Power Supply
CX-DC30
Shenzhen Chuangxin Instruments Co., Ltd.
DC power supplyThis serial single output switch power supply is a kind of DC regulated power supply with high efficiency and stability.
-
product
Modular DC Electronic Load
N3300A Series
The new N3300A Series of dc electronic loads is fast, accurate, and ideal for increasing production throughput in high volume dc power supply manufacturing. This series consists of a full rack width (1800 watts max) mainframe and a half rack width (600 watts max) mainframe, and 7 interchangeable electronic load modules. The modules provide a variety of voltage, current and power ratings. New dc connectors for test system configurations are now available on all modules.
