Optical Attenuators
Reduce optical power by inducing loss.
-
product
90/120 GHz Single Channel Optical Module
N1032A
The N1032A is an optical plug-in module for the DCA-X mainframe that includes one optical channel up to 120 GHz.
-
product
Attenuators
Teledyne Microwave Solutions (TMS) offers a variety of analog controlled attenuators operating over a 10MHz to 26GHz range. With many units operating over many octaves, switching speeds less than 100nS and attenuation control up to 50dB, TMS has a product that meets your demanding needs.
-
product
Attenuators
Teledyne RF & Microwave offers a variety of analog controlled attenuators operating over a 10MHz to 26GHz range. With many units operating over many octaves, switching speeds less than 100nS and attenuation control up to 50dB, RF&M has a product that meets your demanding needs.
-
-
product
Programmable Step Attenuator, DC to 40 GHz, 0 to 70 dB, 10 dB Steps
84907L
The Keysight 84907L programmable step attenuator offers coaxial measurements to 40 GHz in a compact, rugged design. It offers repeatability of better than 0.03 dB, excellent life greater than 5 million switching cycles per section) and an attenuation range of 0 to 70 dB in 10-dB steps. This latest design evolution sets new standards for size and performance. High attenuation accuracy and low SWR are achieved through the use of miniature thin-film attenuation cards composed of high-stability tantalum nitride film of saphire substrate. Insertion loss is outstanding, with with only 2,4 dB of loss at 40 GHz. The compact size of the unit, 35% smaller than the Keysight 8495/7 (26.5 GHz) family, allows for easy integration into instruments and ATE systems.
-
product
Coaxial Fixed Attenuator, DC to 12.4 GHz
8491A
The Keysight 8491A coaxial fixed attenuator provides precision attenuation, flat frequency response and low SWR over broad frequency ranges. The attenuator has type-N connectors and is available in nominal attenuations of 3 dB and 6 dB, as well as 10 dB increments from 10 dB to 60 dB. This attenuator is swept-frequency tested to ensure specification compliance at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
product
Attenuators
Keysight Attenuators offer a compact, rugged design with exceptionally low insertion loss. Our latest design evolution sets new standards for size and performance. Keysight Attenuators provide excellent repeatability and safeguard your test platform from failures, downtime, and lost production. Discover which of our Attenuators best suits your test and measurement needs.
-
product
Mini Fiber Optic, Contact, ITA, Multimode
610113173
* This contact available for purchase as a patchcord only. Choose link below to configure as a patchcord. Primary mating contact 610113172. (May mate with other Receiver contacts, as well.)
-
product
Mini Fiber Optic, Patchcord, Receiver, 36", Multimode, 62.5/125, Single Ended
7-416804000-036
Mini Fiber Optic, Patchcord, Receiver, 36", Multimode, 62.5/125, Single Ended.
-
product
Manual Step Attenuator, DC to 18 GHz, 0 to 110 dB, 10 dB steps
8496B
The Keysight 8496B dc to 18 GHz manual step attenuator offers exceptional repeatability and reliability. Attenuation is provided in 10 dB steps from 0 to 110 dB. Precision gold-plated leaf springs ensure long life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
-
product
Mini Fiber Optic, Patchcord, ITA, 36", Multimode, 62.5/125, to LC
7-415804512-036
Mini Fiber Optic, Patchcord, ITA, 36", Multimode, 62.5/125, to LC
-
product
PXI Attenuator
Keysight offers step attenuator modules that operate across a broad frequency range of DC to50 GHz.
-
-
-
product
Attenuators
Flann manufactures a portfolio of both manual and programmable attenuators that cover a wide range of applications and waveguide bands
-
product
65 GHz Single Channel Optical Module
N1030A
The N1030A is a plug-in module for the DCA-X mainframe that can be configured with one 65 GHz optical channel, or one 65 GHz optical and one 95 GHz electrical channel.
-
product
Variable Attenuators
Wuhan Sunma Technology Co., Ltd.
SunmaFiber offer optical variable attenuator is used for continuously variable optical signal attenuation. As the attenuator is used in the laser system for the on-line testing, there can be used in the digital system of communication devices (such as:PHD, SDH) and also in the system of adopting analog modulation (CATV).
-
product
Fixed Attenuator (Waveguide)
RF Lambda’s fixed waveguide attenuators are used to attenuate RF signals with a waveguide interface. They come in a variety of different frequencies and power levels depending on the application.
-
product
Attenuators And Pulse Limiters
A bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions. There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration an attenuator directly at the pulse generator output is inevitable.
-
product
Precision Programmable Attenuator
RCDAT-30G-30
Mini-Circuits’ RCDAT-30G-30 is a precision programmable attenuator covering an extremely wide bandwidth, from 0.1 to 30 GHz. Its unique design allows attenuation settings to be programmed from 0 to 30 dB, in 0.5 dB steps with monotonic attenuation change per dB, even at the highest frequencies and attenuation settings. The attenuator can be controlled via USB or Ethernet, allowing control directly from a PC, or remotely over a network. VHF / UHF / L / S / C / X / Ku / K band testing.
-
product
Programmable Attenuators
JFW offers 50 Ohm and 75 Ohm programmable attenuators with either relay or solid-state designs. 50 Ohm Relay Step Attenuators, 50 Ohm Solid-State Step Attenuators (TTL), 50 Ohm Solid-State Step Attenuators (USB), 75 Ohm Relay Step Attenuators, 75 Ohm Solid-State Step Attenuators, Analog Programmable Attenuators, High Power Solid-State Step Attenuators.
-
product
Optical-Electrical Converter - MATRIQ
The O2E is a high bandwidth, broadband optical to electrical converter.Available in a range of configurations; choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
product
RF Attenuators
Bird manufactures a broad spectrum of devices from 2 W to 4000W. Our resistive product portfolio includes air-cooled, water-cooled, oil-dielectric, convection cooled, and conduction cooled RF attenuators with a wide range of connectors and attenuation values.
-
product
Attenuators & Loads
*High power handling 100W with a wide range of available attenuation values*Very low PIM <- 160 dBc with excellent return loss performance*Support for 7-16 or 4.3-10 connectors and optional 19 inch rack mount kit*Designed and produced to ISO 9001:2008 certification standards for reliability and quality
-
product
Variable Attenuators
Variable attenuators are an integral part of most BER testing and EDFA characterization setups. All of EXFO's modular (IQS line) and benchtop variable attenuators are built for top performance and pinpoint accuracy. Each model offers a distinct set of features and specifications to suit various testing needs.
-
product
SMA Rotary Attenuator
WATT-6SR1211
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
Attenuators
Shenzhen Tojoin Communication Technology Co., Ltd.
Attenuators are used in a wide variety of applications and can satisfy almost any requirement where a reduction in power is needed. Attenuators are used to extend the dynamic range of devices such as power meters and amplifiers, reduce signal levels to detectors, match circuits and are used daily in lab applications to aid in product design. Attenuators are also used to balance out transmission lines that otherwise would have unequal signal levels.
-
product
Electromechanical Programmable Attenuators
BroadWave manufactures single section 6 dB to 8 section 0 – 127 dB programmable attenuators. •Voltage control and external TTL control •RF Connectors: BNC, N, SMA and TNC •50 and 75 Ohm
-
product
Voltage Control Attenuator
RF Lambda’s voltage control attenuators allow for precision control of RF signals. With a voltage variable control pin the signal can be fine-tuned as needed by the system. These attenuators offer fast response time and wide band operation. Hermetically sealed options are available upon request.
-
product
Voltage Variable Attenuators
Voltage variable attenuators (VVAs) that offer up to 60 dB of attenuation across a broad range of frequencies from 400 MHz to 18 GHz. These voltage variable attenuators are frequently used in applications such as electronic warfare, instrumentation, point-to-point and point-to-multipoint radios, fiber optic and broadband telecom, microwave radio and VSAT, military radios, radar, ECM, SATCOM and sensors, and R&D.
