Strain Gage Signal Conditioners
See Also: Strain Gages, Strain Gauges, Strain Gage Amplifiers
-
Product
Signal Light for Hipot Testers
LX-signal light-HV1
-
2-color indicator light, red, green.With the help of the signal light tower, you can visualize potentially high voltage.
-
Product
PXIe-5650, 1.3 GHz RF Signal Generator
781215-01
RF Signal Generator
The PXIe‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
Signal Level Meter
SLM-5870
-
Compact, light-weight, easy to carry With dual-channel measurement display Channel and single frequency mode
-
Product
Optical Signal Conditioning Products
-
The single-mode fiber N7761A, N7762A and N7764A provide 1, 2 or 4 attenuation channels in a compact remote-controlled instrument. These attenuators provide very fast adjustment and have built-in output power monitoring for accurate power setting and control, as needed for receiver sensitivity testing or in system simulations.
-
Product
Intelligent Panel Mount Meter Amplifier/ Conditioner
MODEL DPM-2
-
The voltage-to-frequency microprocessor makes Transducer Technique's 4-digit panel mount meters the ideal solution for meeting the measurement, display and control requirements of noisy industrial applications, OEMs and system designers. Model DPM-2 accepts any full bridge transducer. Balance and span can be selected via the front keypad, thus allowing the display to read directly in engineering units. Front panel max and tare functions are ideal for industrial weighing applications. Isolated adjustable 9-11 VDC excitation with remote sense and 90 mA drive eliminates the need for external power supplies. Rear screw terminals connectors are included.
-
Product
Signal Processors
-
Designed to handle frequencies ranging from 20Hz to 20KHz. This cutting-edge unit is specifically crafted for a wide array of applications, including room resonance reduction, anti-feedback control, special effects creation, and room equalization.
-
Product
Signal Architect Simulator Software
GNSS
-
The GNSS Signal Architect Simulator Software is ideal for applications requiring: High fidelity simulation of GNSS signals Digital data analysis of GNSS signal effects RF signal generation through digital playback Highly repetitive testing where consistency between test runs is critical Easy to use Graphical User Interface Low initial and support costs
-
Product
CATV Multi Carrier Signal Generators
5112
-
The 5112 is a portable RF signal generator, available in four or six carrier configurations. Each carrier can be activated individually or simultaneously.
-
Product
PCI Strain Gauge Simulator Card, 6-Channel, 1.5k
50-265-406
Strain Gauge Simulator
Designed to simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. It provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Signal Analyzer
-
bsw TestSystems & Consulting AG
The simplest way to measure the phase noise is to compare the Device-Under-Test (DUT) to the source of a spectrum analyzer. With the SA set at the same frequency as the OUT, you see the sum of the SA's and DUT's sideband-power spectrum on the SA display. It is a simple and straight forward method well suited for free running VCO's where the SA is easily an order better.You can improve on this method by establishing a Phase Lock (PLL) between the DUT and the Local Oscillator and create a zero-IF or base-band spectrum analyzer system.
-
Product
Signaling and Display Systems
-
*Display of analog process values*Display and monitoring of process values*Display and monitoring of pulse-shaped signals
-
Product
SIGNAL GENERATOR
TG-1300
-
LOW BATTERY CONSUMPTION COMPACT SIZE DESIGN OUTPUT LEVEL ADJUSTABLE OUTPUT LEVEL DISPLAY MAX. 5BANDS(individual or Simultaneously) PORTABLE TYPE
-
Product
RF Signal Testers
-
RF Signal Generators, Record & Playback Systems, Players, Productivity Tools and More
-
Product
Head Mount Signal Conditioners
-
Head mount signal conditioners are designed to mount in industrial protection heads for use with thermowells. The sensors are small sized and offered in a variety of input and transmission options.
-
Product
Signal And Spectrum Analyzer
FSVA3000
Spectrum Analyzer
An analysis bandwidth of 400 MHz, an outstanding phase noise of –120 dBc/Hz and a high dynamic range – the R&S®FSVA3000 signal and spectrum analyzer has everything needed to keep up with demanding measurement applications such as 5G NR. With its high measurement speed and easy usability, it is the right instrument for demanding signal analysis tasks both in the lab and on a production line.
-
Product
Wi-Fi signal analysers
-
An advanced Wi-Fi analyser is essential to avoid channel interferences in large public or corporate wireless networks.
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
16 Bit 250 KS/s ADC With 16 Channel Multifunction Digital I/Board And Bridge Signal Conditioner
-
The CP246 is a single-width, 6U, CompactPCI/PXI module with 8 channels of Bridge Signal Conditioning feeding 8 independent 16-bit Analog to Digital Converters (ADC). This single-width solution incorporates both signal conditioning and ADC to eliminate the need for complex field wiring.
-
Product
Signal Amplifier
A10150
Amplifier
Model A10150 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, low distortion, signal amplification. With a high bandwidth of 150MHz, 20Vp-p into 50 ohms and a fast transition time of less than 1.8ns, the A10150 is the ideal complimentary amplifier to any high speed signal source that needs a supporting power boost for demanding applications.
-
Product
Blanking Signal Generator II
MS 1609
-
This System used for generating continuous and pulsed variable power outputs (Voltage).
-
Product
Suitable For Strain Gauge / Load Cell Sensors
SEM1600B -
-
Suitable For Strain Gauge / Load Cell Sensors
-
Product
Induced Signals Test
-
The test relates to interfering signals that may be generated by interconnected equipment. Induced signal testing is used to determine if equipment will withstand various signals, such as might be introduced by failures in other equipment to which the test unit is connected.
-
Product
Standard Signal Isolating Amplifier
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Isolation and conversion of standard signals. Calibrated switchable inputs and outputs 0/4 ... 20 mA and 0 ... 10 V signal duplicator with two electrically isolated outputs.
-
Product
20 GHz Signal Source
VCO Series
-
The SC5510A and SC5511A are VCO-based, synthesized signal sources with very low phase noise and an amplitude control of 0.01 dB throughout its -30 dBm to +15 dBm output power range. By utilizing a unique multiple phase-locked loop architecture, phase spurs are kept below -70 dBc across the entire tuning range, even at 1 Hz step resolution. Download the data sheet to see how the impressive features and specifications of these modules make them stand out when compared to other small modular synthesizers. These 20 GHz signal sources include an additional, independent RF2 channel with a tunable frequency range from 100 MHz to 3 GHz and a tuning resolution of 25 MHz. The extra channel makes the modules suitable for either single-stage RF conversion systems or dual-stage image suppression up/down converter systems. Both modules make great general-purpose laboratory signal sources where demanding low phase noise and signal purity are required. They are both ideal choices as an integrated clock source for fast DAC and ADC applications, especially those that require variable sampling rates. Full implementation instructions, GUI, driver software, and example code are provided with each module.
-
Product
Pulser Sensor, Sent Signal, CNEX/ATEX Certificates
SK-S
-
Beijing SANKI Petroleum Technology Co., Ltd.
*convert the mechanical transmission signal of flow meter into electrical pulse signal* send the electrical pulse signal to main-board to realize the metrology function of the flow meter
-
Product
Signal & Power PCB Connector
HPW Series
-
Smiths Interconnect's HPW series is a versatile interconnect with mixed signal and power contacts, up to 15A each
-
Product
Instrumentation And Signal Conditioners Products
-
Stellar Technology offers a full line of readout meters, in-line amplifiers and signal conditioners to complement our broad variety of pressure, load/force/torque, displacement, and temperature sensors. If you’re in need of reliable signal conditioners for your essential operations, our diverse options can provide a solution. Read on to discover all that Stellar Technology can offer your company.
-
Product
Digital Signal Processor Card
CHAMP-AV8
-
Curtiss-Wright Defense Solutions
The CHAMP-AV8 6U OpenVPX digital signal processor (DSP) combines the floating-point performance of the 3rd generation Intel Core i7 processors with the substantial bandwidth and system-enabling features of the 6U OpenVPX form factor. Utilizing a pair of 2.1 GHz quad-core processors featuring the Advanced Vector Extensions (AVX) instruction set, the CHAMP-AV8 DSP card delivers up to 269 GFLOPs.
-
Product
Compact Horizontal Gage
1302
-
The Adcole Model 1302 represents a significant advancement in precision metrology and is an essential part of the production process for sliding cam and shifting camshaft components. The shaft gage features two opposing measuring heads to maximize speed and achieve faster cycle time, while still delivering the sub-micron accuracy and repeatability that have defined Adcole gages as the world standard in cam/crank metrology.
-
Product
Signal Generator
8004
-
5 digit BCD, 1 latch control line, 25 pin female, D type connector. 5 digit BCD, 1 latch control line, 25 pin female, D type connector
