-
Product
250W - Single Output
RGA Series
-
*1/16th Brick Footprint*9-40 Vdc, 9-53 Vdc Inputs*3.3 up to 40 Vdc Outputs*Up to 20 A max Output Current*Non-Isolated Step-Down*-40 to 110 °C Case Temperature*Rugged 5-sided Aluminum Case
-
Product
Thermo Hygrometer Data Logger
HD2101.2
-
Thermo hygrometer, datalogger, instrument measuring range for temperature -200°C...+650 °C; for humidity 0...100% RH.
-
Product
Cable Assembly, 9-Pin D-Type, Male to Unterminated With Cut Ends, 0.5m, HV
A009DM5-C-HA050
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
Product
FieldFox C Handheld Microwave Analyzer, 6.5 GHz
N9914C
-
Capture elusive signals with up to 120 MHz gap-free, real-time bandwidth. Capture elusive signals with up to 120 MHz gap-free, real-time bandwidth. Measure all four S-parameters simultaneously with 115 dB dynamic range. Make accurate spectrum analyzer measurements (± 0.3 dB) without warmup. Perform over-the-air measurements for 5G NR and LTE. Use GPS/GNSS for geolocation and timestamping.
-
Product
PC-based Data Acquisition Boards
-
Data Acquisition and PlaybackPCI, cPCI / PXI : 32bit, 33MHz64 MB/sec data streaming2 OMNIBUS Modular I/O sitesExternal trigger & clockOn-board DDS timebase & timers/countersControlled from Windows or Linux based applicationHuge suite of C++ software componentsMMX optimized DSP analysis components
-
Product
Indoor Digital Hygro-Thermometer
PHHT15
-
Indoor Relative Humidty and Comfort Level IndicatorClock Display with Alarm FunctionSelectable Celsius or Fahrenheit DisplayTemperature Range: -50 to 70C / -58 to 158 FTemperature Accuracy: +/- 1 C (2 F)Humidity Accuracy: +/- 5%Humidity Display Resolution: 1%Sampling Period: 10SBattery: AAA, 1.5V (Included)Dimensions: 4.13' H x 3.94' W x 0.91' DWeight: 4.48 oz.Sold as : Unit
-
Product
High Temperature Transverse Extensometers (700 C)
Model 7675
-
Jinan Testing Equipment IE Corporation
Designed for transverse or diametral strain measurement in environmental chambers where the entire extensometer must be exposed to elevated temperatures. These capacitive extensometers may be used up to 700 C (1300 F) without any cooling.
-
Product
79W to 153W - Single Output
CUS200LD Series
-
*Convection or Conduction Cooled*Up to 206W Peak Power Capability*Low 31mm Height*-40°C Ambient temperature start up
-
Product
Pyrometers
-
Tempsens offers wide range of high accurate non contact pyrometers in temperature range 0 to 3200°C for various industrial applications.
-
Product
DCDC
DP Series
-
The DP family is an economically priced high performance series of regulated DC/DC converters offering single and dual outputs. Features include MOSFET design operating at a switching frequency of 100Khz, continuous short circuit protection, LC input filter, 500 Vdc I/O isolation, and an operating temperature range of -25°C to +71°C with no derating. These miniature converters maintain excellent regulation over varying line and load conditions (0.2% for line and 0.5% for load). They are packaged in an IC compatible 24 pin DIP configuration measuring 1.25” x 0.8” x 0.4” high.
-
Product
2-port/4-port GigE PCI Express Card
AX92322
-
The AX92322 is a GigE compliant PCI Express card supporting two or four independent Gigabit Ethernet ports. It features PCI Express x4 interface and has four powerful independent Intel® Ethernet Controller i210-AT. The GigE frame grabber card supports 9.5KB Jumbo Frame and IEEE 1588 to enable faster and more accurate throughput of data. The AX92322 is built for machine vision and surveillance applications in industrial IoT field. This PCI Express frame grabber card is designed to help customers develop and deploy machine vision and surveillance applications which will greatly benefit through reduce the cost and simplify system integration. Moreover, the AX92322 has a wide operating temperature of 0˚C to 70°C, making it suitable to be used in most server environments. The advanced GigE frame grabber runs on Windows® 7, Windows® 10 and Linux.
-
Product
Fanless Embedded System With Intel® Atom™ Processor E3845 1.91 GHz, HDMI, VGA, 2 GbE LANs, 4 USB And 4 COM
eBOX620-841-FL
-
The eBOX620-841-FL supports the latest 22nm quad core Intel® Atom™ E3845 processor. The eBOX620-841-FL is rugged and designed to offer reliable operation in extreme temperature ranging from -40°C to +60°C (-40⁰F to +140⁰F). Its IP40-rated, rugged aluminum cold-rolled steel enclosure allows it to withstand operations in harsh environments and vibration of up to 3 Grms (with CFast™). The industrial grade embedded platform has full power protection with OVP, OCP, SCP and is CE certified.
-
Product
PXI-2566, 16-Channel, 2 A, SPDT PXI Relay Module
778572-66
Relay
16-Channel, 2 A, SPDT PXI Relay Module—The PXI‑2566 is a general-purpose switch module that features independent single‑pole double‑throw (SPDT) Form C armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2566 is ideal for switching, routing, and controlling high-current signals. Each relay channel has a normally closed (NC), normally open (NO), and common (COM) terminal.
-
Product
Integrating Spheres For UV
-
Konica Minolta Sensing Americas, Inc
Instrument Systems offers complete measurement solutions for UV-A, -B and -C radiation starting from 200 nm. The operation of the well-proven Instrument Systems spectroradiometers, e.g. CAS series, with integrating spheres made from PTFE facilitate high sensitivity measurements of UV radiant flux.
-
Product
Fanless Embedded System With Intel® Atom® Processor E3845/E3827 For Railway, Vehicle And Marine PC
tBOX810-838-FL
-
The tBOX810-838-FL fanless box PC is certified with eMark, ISO7637, EN50155, EN50121 and IEC60945 for transportation applications. The tBOX810-838-FL is powered by the Intel® Atom® processors E3845 quad-core 1.91GHz and E3827 dual-core 1.75 GHz with onboard DDR3L memory up to 4GB. Measuring only 164 x 108 x 44 mm and 0.77kg, the mini fanless embedded system supports a wide operating temperature ranging from -40°C to +70°C and 9 ~ 36V wide DC input for wide range of harsh environmental conditions. Additionally, the vehicle/railway/marine box PC has high integration ability with two full-size PCI Express Mini Card slots, one SIM card which makes it a multi-function device for transportation applications. The tBOX 810-838-FL is definitely the top choice for M2M intelligent system for railway, marine, and vehicle solutions.
-
Product
sbRIO-9264, Non-Enclosed, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
781119-01
Voltage Output Module
Non-Enclosed, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The sbRIO‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the sbRIO‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection. Non-enclosed modules are designed for OEM applications.
-
Product
ARINC 429 PXI Express Test & Simulation Instrument
PXIe-C429
-
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
CX4000 – FTIR Gas Analyzer
-
Gasmet CX4000 is an industrial multi-component FTIR gas analyzer for continuous emission monitoring applications, integrated into a Continuous Emissions Monitoring system (CEMS II e). It can be used to measure up to 50 components simultaneously, and additional gases can be easily added without any hardware changes. The corrosion-resistant sample cell is heated up to 180 °C, which makes CX4000 an ideal tool for analyzing trace concentrations of pollutants in wet, corrosive gas mixtures.
-
Product
VXI 11 Slot C-Size
-
High-Performance 11 Slot C Size VXI Monolithic Backplane with High Current Din Conncectors.
-
Product
AC/DC Power Supply 700 W
MEG-700A3T
-
AC/DC power supply from Delta | input 90 - 264 VAC | configurable output | temperatures from -20 to +70 °C
-
Product
Beer Refractometer
PA203X-009-800-801-802-804
-
Multi-scale Digital Beer Refractometer for measuring Plato, Dissolved Solids, Specific Gravity D20/20, Brewer’s Points, and Propylene Glycol Freeze Point °C.
-
Product
Optical Tester
Model C
-
The Model C Optical Tester is just such a device. Extremely small geometric distortion and focal length deviation can be viewed and measured easily.
-
Product
Cable Assembly, 9-Pin D-Type, Male to Unterminated With Tinned Ends, 0.5m, HV
A009DM5-T-HA050
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
Product
NI-9201, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
783730-01
Voltage Input Module
±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9201 is an effective combination of channel count and speed at a low price for an economical multifunction system. The module features up to 100 V of overvoltage protection for errant signal connection or unexpected signals to the individual channels.
-
Product
NI-9211, 4-Channel, 14 S/s/ch, ±80 mV C Series Temperature Input Module
779001-01
Temperature Input Module
4-Channel, 14 S/s/ch, ±80 mV C Series Temperature Input ModuleThe NI‑9211 includes anti-aliasing filters, open-thermocouple detection, and cold-junction compensation for high-accuracy thermocouple measurements. The NI‑9211 features NIST‑traceable calibration and a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range.
-
Product
High-Frequency Ultrasonic Imaging System
USPC 3060 UHF
-
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
The ultrasonic imaging system USPC 3060 UHF is optimized for the testing wih high frequencies and delivers high resolution B-, C-, Dand F- scans. It consists of a scanning system with water tank and the external pulser-/receiver module as well as a 19”-rack with scanner controller and the ultrasonic system and monitor, keyboard and mouse.
-
Product
Conduction Cooled Interface Board Supporting up to 5 Multi Function Channels
EXC-1553PMC/Px(S) / EXC-1553ccPMC/Px(S)
-
MIL-STD-1553, conduction cooled, interface board. Supports up to 4 multi function channels.The EXC-1553PMC/Px(S) and EXC-1553ccPMC/Px(S) are multi-channel (up to four) MIL-STD-1553 interface boards for PCI Mezzanine Card compatible computers.Multi Function:Each channel operates simultaneously as a Bus controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. In addition, error injection (BC and RT modes) and error detection (all modes) are supported on each channel.Single Function:Each channel operates either as a Bus Controller, Remote Terminal, or Bus Monitor.NOTE: PxS is NOT compatible to the MCH family of cards.The EXC-1553PMC/Px(S) and EXC-1553ccPMC/Px(S) are supplied with C drivers, including source code, and Merlin+ Windows software.
-
Product
High Temperature Furnace COD Gages (1200 C or 1600 C)
Model 3548COD
-
Jinan Testing Equipment IE Corporation
These COD gages mount on a water-cooled bracket, which is mounted on the furnace side cut-out or with optional load frame support brackets. The standard temperature version (to 1200℃) is supplied with high purity alumina rods. The high temperature option is furnished with alpha grade silicon carbide rods. Rods are made to order to the length required for your furnace. Mounting brackets may be integrated with the furnace cut-out. Epsilon can also provide optional load frame mounting brackets to fit your test frame. Contact edges on the test sample should be somewhat rounded (not sharp knife edges) for best performance with this model. The Model 3548COD extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Temperature Calibration Equipment
-
We offer wide line of temperature calibration equipment for calibration of contact type sensors (Baths/furnaces) and non contact type sensors (Black Bodies), available in temperature range -80°C to 1700°C.
-
Product
Digital LCD Display Drivers
-
Analog Devices DecDriver® family of digital LCD display drivers helps meet the increasing demand for higher resolution displays in home entertainment and home theater. This portfolio of products offers improved power, enhanced image quality, and lower costs, and has been optimized for a wide range of displays and performance needs. Our digital LCD display drivers operate over the commercial temperature range of 0°C to 85°C and include features such as a flexible digital input format that allow the devices to be used in parallel in high resolution displays.
