-
Product
Anemometer meter
AVM 712
-
3 Measurements in one instrument. Air flow: CMM( M3/min) and CFM(FT3/min). Air velocity: m/s, ft/min, km/h, knots, mile/h. Air temperature: Degree C and F. 3 air flow mode: Instant, 2/3rd Velocity Max, Average
-
Product
ICP Electret Array Microphone
130A23
-
Nominal Microphone Diameter: 1/4" Frequency Response Characteristic (at 0 incidence)Free-FieldInherent Noise (A Weighted)<30 dB(A) re 20 Pa<30 dB(A) re 20 Pa Dynamic Range (High)150Environmental Temperature Range ( Temperature Effect on Output (-10 to +50 C)<0.7 dB<0.7 dB[2] Influence of Axial Vibration Excitation Voltage 18 to 30 VDC18 to 30 VDC
-
Product
DC/DC Converter 120 W
CTS-120-6874-D
-
DC/DC converter with 120 W from Premium | input ranges 43.2 - 90 VDC | output 12 V | operates in temperatures from -25 - +85 °C | designed according to EN50155
-
Product
Cable Assembly, 50-Pin D-Type, Male to Male, 2m HV, Exit Away From Pin 1
40-970-050-2m-MM-HV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
NI-9203, 200 kS/s, ±20 mA, 8-Channel C Series Current Input Module
779516-02
Current Input Module
200 kS/s, ±20 mA, 8-Channel C Series Current Input Module - The NI‑9203 is intended for high-performance control and monitoring applications. It features programmable input ranges and variable connectivity options. To protect against signal transients, the NI‑9203 includes a channel‑to‑earth ground double‑isolation barrier (250 Vrms isolation) for safety and noise immunity.
-
Product
Ultra Low Temperature Data Logging System
ULT90-9
-
MadgeTechs Ultra Low Temperature Freezer Validation System can measure and log data as low as -86°C. It can be placed in small and large freezers of varying configurations.
-
Product
Diagnostic Software
Developer Toolbox
-
The world's most widely used SCSI diagnostic software product is now available in a reference library. The Developer Toolbox uses our proven interface to access SCSI, Fibre Channel, or ATAPI devices from Visual Basic or C++ running on all 32 bit versions of Windows.
-
Product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Cut Ends, 1m, HV
A037DF4-C-HA100
Cable Assembly
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
200KHz DIGITAL LCR METER
VE2836U
-
200KHz Digital LCR Meter that can test Inductance (L), Capacitance (C), AC Resistance, Q, D, ESR and Tan. Comes with Bin Selection option.Test Frequency : 50Hz ~ 200KHzTest Signal Voltage : 100mV , 300mV , 1000mV , 2000mV
-
Product
Passive XMC-to-PCI Express Adapter
5935
-
The Technobox, Inc. P/N 5935 is designed to adapt a single-wide XMC card to a 1X PCI Express slot. The 5934 supports P15 only and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
Product
Differential Probe / Paired ProbeTOP
-
*1 Measured at 23°C environment connected to PS-02/PS-03 power supply(optional)*2 Broadband Noise, Bandwidth 30 MHz*3 Referred of output*4 Must be met to achieve best performance and avoid Damage to the Probe*5 Parts#890-880-104 : Twinholder M6 and 890-880-112 : Pair of Rail Clip Connectors 4mm are optional.
-
Product
High Temperature XY Planar Biaxial Extensometer 1200 C or 1600 C)
Model 7651
-
Jinan Testing Equipment IE Corporation
Model 7651 extensometers measure combined in-plane strains in flat cruciform specimens tested in machines capable of simultaneous X and Y (perpendicular) axial loading and on standard flat samples tested in pure tension. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7651 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to eliminate crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃(2900°F) high temperature option.
-
Product
NI-9421 , 24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module
779136-01
Digital Module
24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module - The NI‑9421 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels and has an LED indicating the state of that channel. The NI‑9421 offers isolation between the input channels and earth ground.
-
Product
LGA 1151 Intel® Xeon® E & 8th/9th Generation Core™ MicroATX Server Board with 4 DDR4, 4 PCIe, 6 USB 3.1, 8 SATA3, Quad/Dual LANs, IPMI
ASMB-586
-
- LGA 1151 Intel® Xeon® E and 8th/9th generation Core™ i7/i5/i3 processors with C246 chipset- DDR4 ECC/Non-ECC 2666/2400/2133 MHz UDIMM up to 128GB- One PCIe x16, two PCIe x4 and one PCIe x1 slots- Triple displays - DVI-D, VGA and HDMI 2.0 ports- Eight SATA3 ports and six USB 3.1 ports- 0 ~ 60° C ambient operating temperature range
-
Product
17" Fanless Panel PC With Intel® Atom™ X6425E Processor
PPC-417 EHL
Panel PC
17” SXGA TFT LCD with resistive (default)or projected capacitive(by request) touchscreenIntel® Atom™ x6425E quad-core, 2.0 GHz processorFanless, slim designSupports 1 x 2.5" SATA and 1 x M.2 B key slot for expansion1 x PCI/PCIe x1 expansion slotWide operating temperature range (-20 ~ 60 °C/-4 ~ 140 °F)Wide range DC support (9 ~ 32 VDC)1 x isolated RS-422/485 with automatic flow controlDual 2.5GBASE-T Ethernet supports Time-Sensitive Network(TSN) technology
-
Product
Functional Testing For Critical Software
RapiTest
-
*Requirements-based testing for Ada, C & C++ on-host & target*Reduce test authoring effort through easy-to-use test formats*Manage project artifacts with requirements traceability*Simplify verification through integration with your CI tool*Produce evidence for DO-178 and ISO 26262 certification
-
Product
HS1760/MIL-STD-1760E Network Interface Controller for PCI Express
PCIe-1760-NIC-FP
-
Avionics Interface Technologies
Configuration Variants available: PCIe-HS1760-NCNT: One NC Node and One NT Node, PCIe-HS1760-NCNC: Two NC Nodes, PCIe-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data - 75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
-
Product
Incubator
I
-
In the laboratory, the Memmert incubator I is ideal for all applications with temperatures up to +80C specifically for incubating living cultures at +37 C. Thanks to the finely-tuned control technology, critical temperature overshoots are completely ruled out, valuable loads are therefore warmed up particularly carefully in this highly precise microbiological incubator.
-
Product
Infrared Thermometers
-
Instant, less-than-a-second temperature readings of any surface, °F/°C switchableIdeal for food preparation, pharmaceuticals, field use, electronics, and safety inspectionFeatures minimum/maximum memory, average readings, and high/low audible alarms (Cat. No 4484)
-
Product
Precision Low Power FGA™ Voltage References
ISL60002
-
The ISL60002 FGA™ voltage references are very high precision analog voltage references fabricated on Renesas' proprietary Floating Gate Analog technology and feature low supply voltage operation at ultra-low 350nA operating current. Additionally, the ISL60002 family features guaranteed initial accuracy as low as ±1.0mV and 20ppm/°C temperature coefficient. The initial accuracy and temperature stability performance of the ISL60002 family, plus the low supply voltage and 350nA power consumption, eliminates the need to compromise thermal stability for reduced power consumption making it an ideal companion to high resolution, low power data conversion systems.
-
Product
Calibrator, 0 to 24 mA, Current, 185 mm, 78 mm, 38 mm, ± 0.5%, 265 g
72-6694
-
*Adjustable 0 to 24 mA current source*Current calibrator drives loads up to 500 Ω*Large LCD display*Sampling Time : Approximately 0.4 seconds*Over Input Indicator : 1*Operating Temperature : 0°C to 50°C ( 32°F to 122°F)*Size : 185 × 78 × 38 mm (7.3 × 3 × 1.5 inches)*Weight : 265 g (0.58 lb) including battery*Requires one 9 V battery - not included*12 month limited warranty *view Terms & Conditions for details
-
Product
NI-9202, ±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module
784400-02
Voltage Input Module
±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module - The NI-9202 has excellent flexibility to meet the needs of your applications. The module has 16 simultaneous sampling, differential input channels to create large, distributed systems in a rugged form factor. It … also has configurable filters to eliminate noise in your system while maintaining low-latency to be used in control systems.
-
Product
Dual LGA3647-P0 Intel® Xeon® Scalable EATX Server Board with 24 DDR4, 5 PCIe x16 + 1 PCIe x8, 10 SATA3.0, 6 USB3.0, Dual 10GbE, IPMI
ASMB-935
-
- EATX server board with dual Xeon Scalable processors- DDR4 2933 MHz RDIMM up to 3TB, support Intel Optane DC Persistent Memory- Five PCIe x16 (Gen3) and one PCIe x8 (Gen3) for three double-deck cards- Intel® X557-AT2 dual 10GbE ports- Ten SATA3.0 and six USB3.0 ports- One M.2 2280 (SATA / PCIe compatible)- 0 ~ 40 °C ambient operating temperature range
-
Product
ARINC 429 Test & Simulation Interface for VME
VME-429
-
Avionics Interface Technologies
4, 8, 16, 32, or 64 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full Error Injection & Detection - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application interface supporting C, C++, C#, and .net development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME - Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
Rugged PC Compatible
SYS-405Q
-
The SYS-405Q is a rugged, industrial system capable of operating at extended temperatures from -40° to +85°C without requiring a fan or heat-pipe. The SYS-405Q is based on the quad-core Intel® Atom™ E3845 processor and protected by a rugged enclosure.The SYS-405Q includes dual Ethernet, dual MiniPCIe, USB 3.0, serial ports with RS-232/422/485 and two independent displays via DisplayPort, and/or Analog VGA.
-
Product
C Series Digital Module
Digital Input Module
The C Series Digital Module interacts with a range of industrial switches, transducers, and devices. Some modules include an LED per channel that indicates the state of the channel. It supports input, output, or a combination of digital lines, and they can interact with a variety of voltages and logic levels, so they are well-suited for a variety of benchtop and industrial environments. Additionally, the C Series Digital Module also offers isolation options and sinking or sourcing capabilities to add further protection to your digital I/O application. When you use the C Series Digital Module with CompactRIO, you can use LabVIEW FPGA to create custom high-speed counter/timers, digital communication protocols, pulse generation, and more.The C Series Digital Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Ethernet to Modbus RTU Interface
Model 9099
-
* Use Modbus TCP/IP, VXI-11, or Raw Sockets (Telnet) or to control Modbus RTU slave devices.* No special driver required which eliminates driver problems.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* Interfaces with PLCs or any Modbus TCP/IP Controller.* Fully VXI-11 compliant.* Works with Agilent, NI and Kikisui VISA libraries.* Internal webserver with sample Modbus device control pages for Watlow F4, F4T and EZ-Zone Controllers.* Network connectivity eliminates GPIB Bus Extension problems.* Allows multiple users to access the Modbus network or devices.* 9099 is a 2x to 5x faster than the 8099 and includes a new Modbus device control page.
-
Product
30W to 1800W - Single Output
HWS/HD Series
-
*Limited Lifetime Warranty*-10 to +71°C Operation (-40°C start up)*Universal input (85 - 265VAC)*Conformal coated PCBs*Class 1 Div 2 option (/RYHD suffix)
-
Product
Audio/ Video
Audio Analyzer
Our experts/ physicist can help you in the Implementation of your algorithms including BPR, NUC , Edge Detection and movement analysis algorithms.Our development environment is based on C++ and LabVIEW libraries or tools such as Vision Builder for Automated Inspection from National Instruments.
-
Product
Sound Level Calibrator
511E
-
Accepted internationally 1 kHz represents the "0 dB" reference point of A, B, C Weighting and other filters utilized in acoustic measurement. The Pistonphone - a mechanical sound source - offers a slightly higher degree of accuracy at a substantial increase in cost. In addition, the 200 or 250 Hz operating frequency is mechanically limited and not suited for measurements of filtered inputs. The 0.2 dB accuracy is quickly lost in the 0.7 to 1.5 dB tolerances acceptable for weighting filters at frequencies around 250 Hz.
