Drivers
translate general instructions into hardware specfic commands.
-
product
Bus Isolation Board
MS 1705
- Bus Interface - ISA96 Bus, 6U form factor- 16-bit Data Bus- 20-bit Address Bus & Control Signals- Isolated Bus Interface- Driver interface for Windows2000/XP/VISTA and LINUX OS
-
product
PXIe-5764, 16-Bit, 1 GS/s, 4-Channel PXI FlexRIO Digitizer
785171-01
The PXIe-5764 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PXIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
product
Laser
BDS-SMY Series
*Pulse Width Down to 50 ps*Repetition Rate 50 MHz (20 MHz Available on Request)*Free Beam or Fiber Output*CW-Equivalent Power 0.3 mW to 0.5 mW*All Electronics Integrated*No External Driver Unit*Simple +12 V Supply*40 mm x 70 mm x 120 mm
-
product
65 MHz Single Channel Driver Card
40490
One channel, 65 MHz driver with an output voltage capability of ±20V. There are two inputs--a standard input with up 65 MHz capability and an optically isolated input with 20 MHz capability. Either input can be selected.
-
product
PXIe Audio Analyzer
M9260A
M9260A is significantly different from the traditional general purpose PXI digitizer modules which are being used for today's audio measurement. In order to achieve fast test speed and high performance it comes with large one million sample arbitrary waveform buffer and one million sample "limitless" input buffer, as well as super-linear/low noise amplifiers and digital to analog converters. This enables M9260A's ultra-low residual distortion and high amplitude accuracy. M9260A is now an important part of Keysight Radio Test Solution, and may also be easily integrated into any audio related PXI test system with its developer-friendly drivers and commands.
-
product
Automotive Power
The automotive power lineup can support a variety of automotive system requirements and includes intelligent power switches, thermal FETs, MOSFET drivers, and a motor driver.
-
product
Data Communications
Renesas has receivers, line drivers and encoder-decoders for data communications applications, as well as products that cover ARINC and Manchester specifications.
-
product
LC Software
Shimadzu LC Driver for OpenLAB CDS
Control of Shimadzu’s Nexera and Prominence series by OpenLAB CDS is now available by adoption of Agilent’s RC. Net driver standard.
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-600B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
Single Board Computers
At the heart of every system is the single board computer. Elma sells, supports and integrates the latest in Intel and Freescale based single board computers from industry leading partners including Artesyn Embedded Computing, Concurrent Technologies, GE-IP and Interface Concept, as well as a few other specialized boards. When integrated as one of our popular AppliPaks, the SBC becomes part of a tech refresh solution which includes operating system and driver integration, plus mezzanine I/O or storage to form a bundled assembly sold and supported by Elma.
-
product
Digital Attenuator Operating Frequency of 1 to 20 GHz
LDA Series
The LDA series of Lab Brick® RF and Microwave Programmable Digital Attenuators includes 50 Ohm and 75 Ohm bidirectional RF step attenuators with calibrated operation up to 20 GHz. These USB powered and controlled units require no additional DC supply voltage. They are easily programmable for fixed attenuation or swept attenuation ramps directly from the included GUI. Lab Brick Digital Attenuator API DLL, Linux drivers and LabVIEW-compatible drivers are also available for custom programming applications.
-
product
Ferrite Compression Drivers
Professional compression drivers with precision-built ceramic magnetic design, advanced molding and assembly technologies.
-
product
Driver Amplifiers (< 3 W)
Qorvo's driver amplifiers are designed to provide good linear or efficiency performance for gain stages prior to the final power amplifier in a transmitter chain. These products support frequencies up to 46 GHz, using process technologies such as InGaP HBT, power pHEMT, E/D pHEMT and GaN.
-
product
Diode Laser Driver
D200
The D200 is a compact, DC-coupled fast laser driver, providing up to 4 amps of regulated constant current. A built-in edge-triggered pulse generator produces up to 1 microsecond pulse widths and 2 nanosecond transition times, capable of driving lasers with forward voltages up to 9 volts. A pulse-follower mode is also provided, accommodating externally-defined trigger widths up to 100% duty continuous-wave (CW). Power, pulse width, drive current and differential triggering functions are accessible through a ribbon cable header for embedded OEM applications. A low-inductance laser drive interface permits direct laser connection or custom interposer and flex-cable attachment.
-
product
Line Drivers
The Asynchronous Line Driver (ALD-19.2) utilizes state of the art digital CMOS technology to provide a feature filled product at a very affordable price. The ALD-19.2 transmits and receives data bi-directional at data rates up to 19.2kbps. The unit is designed for asynchronous Point-to-Point operation.
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-400B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
J-Type Thermocouples Grounded (32 deg F to 900 deg F )
745685-J01
J-Type Thermocouple, 32°F to 900°F Temperature Sensor - The J-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the J-Type Thermocouple and acquire synchronized temperature data in units of degrees. The J-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
product
Ethernet Adapter Supporting up to Twenty ARINC-429 Channels in Any Combination
ES-9810/A0 (RUNET II)
The EXC-9810/Ax is an Ethernet adapter supporting up to twenty ARINC-429 channels in any combination of transmit and/or receive. All of the channels feature error injection and detection.adapter. Its small size and ability to interface through Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the ARINC-429 bus, both in the lab and in the field.The receive channels allow for the storage of all selected labels with status and time tag information appended to each word, and also allow for filtering and multi-storage modes of data words. The transmit channels operate via a transmit ‘instruction stack’ which allows scheduling of data transmissions and reduces the need for host computer intervention. The EXC-9810 supports up to four independent 8000 family avionics communication modules, allowing multiple different protocols to be mixed and matched on a single card. Modules available include MIL-STD-1553, MIL-STD-1760, MMSI, ARINC-429, ARINC-708, ARINC-717, Serial, Discrete and CAN bus. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.The EXC-9810/Ax adapter is supplied with C drivers, including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application (only versions 8.1 or higher). Please see multi protocol 8000 modules for additional information on protocols that can be added to this card.
-
product
AFDX ® / ARINC 664 Test And Simulation PXI Module
PXI-C664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Stard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applicationsWindows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
product
High Resolution USB Programmable Digital Attenuator 200 to 6,000 MHz
LDA-906V Lab Brick®
The Lab Brick LDA series of Digital Attenuators bring affordability, functionality, reliability and simplicity to the microwave test bench. The LDA products range from 6 MHz to 20 GHz with input level tolerance to 2 Watts and step size as small as 0.1 dB. Lab Bricks use a native USB HID interface to avoid the difficulties inherent in using older serial or IEEE-488 interfaces implemented over USB. As a result, Lab Brick users can get to work faster without having to install kernel level drivers, and Lab Brick devices can be easily used on any system that supports USB HID devices, including low cost embedded computers using Linux or similar operating systems.
-
product
PXIe-6358, 16 AI (16-Bit, 1.25 MS/s/ch), 4 AO, 48 DIO, PXI Multifunction I/O Module
781054-01
PXIe, 16 AI (16-Bit, 1.25 MS/s/ch), 4 AO, 48 DIO, PXI Multifunction I/O Module—The PXIe‑6358 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6358 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
ISA Digital IO Board
MS 1804
*Discrete Input / Output 48 Channels*TTL Pulse measurement channels (Timers / Counters) 12 Channels*TTL Pulse Generation 12 Channels*Bi-directional Bus 16 Bit*The Pulse Generation Frequency from 10Hz to 40MHz*The no. of pulses controlled from 1 to 255 pulses*All Channels are compatible with 5V TTL / CMOS*All the pulse input and the output signals and Bi-directional write signals driven through Pin Driver*Standard ISA Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
product
6U CPCI Processor Board
CP62101
LinkedHope Intelligent Technologies Co.,Ltd.
CP62101, a product designed by LinkedHopeTM, is a 6U CPCI processor board based on Intel QM67/HM65 platforms supporting 2nd generation Intel i series CPU, up to 2.5GHz frequency, HD3000/2000 integrated core graphics and dual-channel SO-DIMM memory (800 /1066 /1333) with up to 16GB DDR3 ECC (optional) and up to 64GB on-board SSD storage.CP62101 provides VGA and HDMI display and supports different display terminal output. CRT displays up to 2048 × 1536. Besides, CP62101 provides a wealth of software drivers (BSP) support, including Windows7, Windows Vista, Windows XP, WES 7, VxWorks, Linux, etc., as can reduce system integration workloads and end application development efforts, so to shorten time to market.
-
product
DAWN Dashboard
An HEM Data custom website dashboard offers the following features for you to choose from:* Receive file uploads from the data logger.* Automatically convert the messages to scaled, engineering parameters.* Store the data in a database for fast access and analysis. A secure data warehouse.* Confirm data validity as the data comes to the dashboard. Send an early warning if data is invalid, not logged properly, or stops arriving at the server (logger removed or malfunctioned).* Query the database to find the results of interest.* Display the results as a dashboard using a variety of formats such as histograms, Y-T and X-Y plots, meters, maps, indicators and tables.* Send alerts as a text message or email when user-defined conditions occur. Sample alerts include: unacceptable driver behavior (excessive speed, deceleration, idle time, etc.), geofencing (in or outside a designated area), operating parameters out of range, trouble codes, and fuel theft.* Download files automatically or manually from the website to a local PC for further analysis.
-
product
PXIe-5163, 200 MHz, 1 GS/s, 14-Bit PXI Oscilloscope
785182-01
PXIe, 200 MHz, 1 GS/s, 14-Bit PXI Oscilloscope—The PXIe‑5163 high-resolution oscilloscope has two channels that sample at up to 1 GS/s with flexible and programmable settings for coupling, input impedance, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that facilitates high-speed data throughput and includes analysis functions. This device is ideal for automated and partially automated time- and frequency-domain applications that require high-resolution, low-noise measurements with up to 200 MHz of analog bandwidth and up to 250 V. The PXIe‑5163 also features advanced PXI synchronization and data throughput capabilities.
-
product
PXIe-6375, 208 AI (16-Bit, 3.8 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module
783634-01
PXIe, 208 AI (16-Bit, 3.8 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module—The PXIe‑6375 offers analog I/O, digital I/O, and four 32‑bit counter/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6375 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
Pump Laser Diode Driver
S-110
•LD Driver, EDFA, ASE Broadband Source, 1X4 Optical Switch•Variable Optical Attenuator, Wavelength Meter•SOA Driver, SLED Driver, Pump LD Driver•Pattern Generator & BERT, SFP Transceiver Driver•4Channel Optical Return Loss Meter (Light Source & Power Meter)
-
product
LED Driver Automatic Test System
ATE-2
•This system includes 2 groups (left and right); the 2 groups can work in turn, so that to improve the work efficiency. For example, if the left is on working, then the right can make wire connection. •It can test 4 LED drivers input and output at one time. •The equipment can connect with electronic load and LED load, the two difference loads can be fast switch under the control of computer. •Enable to print out the series number and parameters of sub-quality products by working with a micro-printer, •Enable to achieve the bar-code record function by working with a bar-code scanner. •The test report can be saved as Excel file for consult, statistic and analysis purpose. •Good software interface to freely choose the difference parameters combination, so that to meet different demands. All the parameters can set limit, and with the quality analysis function.
-
product
Combination Board Tester
Qmax Test Technologies Pvt. Ltd.
Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities and conventional PCBs. An In –Circuit device test by configuring Pin Drivers to High Current Pin Driver mode and interface to the UUT either through Clips / Probes or nail bed and on board clock disable HW feature are the all time favorite . The in-built high frequency 14bit Analog Driver / sensors synchronized with digital drivers for covering analog / mixed signal devices with high degree of accuracy.
-
product
PCI-6115, 4 AI (12-Bit, 10 MS/s/ch, Buffer Rate 32MS), 2 AO, 8 DIO, PCI Multifunction I/O Device
778554-01
4 AI (12-Bit, 10 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device - The PCI‑6115 is a simultaneous-sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6115 is ideal for a variety of applications, such as stimulus/response applications that require synchronization among analog input (AI), analog output (AO), and digital I/O. It is also ideal for 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6115 dimensions require chassis slots that can accommodate full-length PCI modules.
