Drivers
translate general instructions into hardware specfic commands.
-
Product
USB-6366, 8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
781445-01
Multifunction I/O
8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6366 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6366 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Single Event Effects Test System
SEE-RAD
-
The SEE-RAD test system brings together the proven features of our ETS780 tester (such as true APG memory test and powerful FA tools) with the newest technology of the Griffin III. With all new high-accuracy DC Parametrics, superior precision pin drivers, and capture memory of 64M, the Griffin SEE-RAD combines the newest innovations in the test industry with our years of experience in Radiation Test.
-
Product
RS-232 Line Driver with Control Signals and LCD Display
Model 224
-
FEATURES: DataSpy® Status Display; Full Duplex & Handshake; Loopback & DTE/DCE Switch; DC to 19.2 KBPS; Supports DTR & DCD; Optically Isolated. The Model 224 RS-232 Line Driver with Control Signals and LCD Display provides for transmission of a handshake signal in each direction, in addition to communicating full duplex data up to 19.2 KBPS and providing complete optical isolation.
-
Product
PXIe-8521, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module
786771-01
Ethernet Interface
PXIe, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8521 is a 100BASE-T1 unshielded twisted pair (UTP) Automotive Ethernet interface for developing applications with the NI‑XNET driver. The PXIe-8521 is ideal for developing applications that require … Automotive Ethernet to test and validate automotive electronic control units (ECUs). The interface provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, which allows it to synchronize with an external network as well as the rest of a PXI system. The PXIe-8521 also provides LEDs on the front panel so that you can monitor the network link and activity.
-
Product
Digital I.O Module with 64 TTL Channels
IO203
-
This I/O module is a dedicated digital I/O module providing a total of 64 TTL channels. The TTL transceivers are TTL and CMOS/TTL compatible and can also set to be CMOS compliant by the Setup driver block. Each of the 64 channels can individually be programmed as input or output. The 64 channels are further separated into two groups of 32 channels each.
-
Product
Pickering Software Drivers and Applications
-
We provide driver packages for LXI and PXI products offering seamless installation and support of all popular Programming languages such as C/C++, LabVIEW™, LabVIEW RT, .NET, VB, LabWindows/CVI, MATLAB®, Python, ATEasy, TestStand™, Veristand™ and Switch Executive™ (via the IVI driver).
-
Product
Modulated Wideband Driver Amplifier
TBMDA2
-
The TBMDA2 modulated wideband driver amplifier is designed in order to create an inexpensive signal source for immunity testing of electronic building blocks and products. It is designed to be driven by the tracking generator output of spectrum analyzers. With its 1dB compression point of +27dBm, it can boost the output power of a tracking generator up to 500mW.
-
Product
Dual-Vision Sensor for Intersection Control and Safety
TrafiSense2 Dual
-
FLIR TrafiSense2 Dual combines best-in-class thermal and visual imaging technology with advanced video analytics to provide vehicle and bicycle presence detection at signalized intersections, day and night. Thermal imaging lets traffic operators see in total darkness and inclement weather. The daylight camera offers additional visual verification for such incidents as wrong-way drivers and animal crossings. In addition, FLIR's analytics capture accurate traffic data, making FLIR TrafiSense2 Dual ideal for real-time traffic management in urban environments.
-
Product
Pulse Tools
-
Faster than hand tools, more powerful than air screwdrivers, and safer than impact drivers, Mountz pneumatic pulse tools are a top solution for heavy fastening operations. Their pulse drive protects workers from injuries caused by high torque shut-off reactions. That means they can safely be used at higher torque settings than other power tools. High-speed rundowns decrease production cycle times, and the durable construction and simple maintenance needs ensure consistent tool uptime. Plus, a precise hydraulic shut-off keeps fastening work accurate for even the most heavy-duty applications.
-
Product
PXI Vehicle Multiprotocol Interface Module
Interface
PXI Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. PXI Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
Torque Tester
WDISR-IP series
-
Management of manual torque tools Built-in battery type. For managing various torque drivers and wrenches. Interlocking with a personal computer or PLC, the torque measurement can be managed at a higher level
-
Product
Bus Switches
-
Bus Switches are devices that enable system architecture to be reconfigured. This reconfiguration is mostly accomplished in the test environment and includes but is not limited to simulation of missile firing and switching in or out a new section of bus interface.Excalibur Systems is the only manufacturer of devices (ESI-R24/27/28) that contain their own TTL driver circuitry that allows them to be directly driven from a computer.
-
Product
Interface and Isolation
-
Analog Devices offers a wide range of digital interface and digital isolators with iCoupler® technology covering the industry’s field bus and peripheral communications standards. Digital isolators, isolated transceivers, isolated A/D converters and isolated gate drivers utilize the award winning iCoupler® and isoPower® technologies for isolation solutions without many of the constraints found in optocouplers. Find design solutions for interface devices including keypad controllers, level translators, and high voltage protection products (channel protection, fault protection, overvoltage protection), and latch-up proof switches and multiplexers.
-
Product
NI-9861, 1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module
781962-01
CAN Interface
1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI‑9861 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The NI‑9861 is ideal for applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
Product
USB-6341, 16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
781438-01
Multifunction I/O
16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB‑6341 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6341 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Programmable LED DC Electronic Load
M98 Series
-
M98 series DC electronic load, as a new generation product of Maynuo Electronic Co., Ltd, is designed for the LED driver application. A special circuit is desiged for the LED driver on the base of the M97XX sereies. Incorporating high-performance chips, the M98XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M98XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications.
-
Product
PCI-8513, 1‑Port, Software‑Selectable/FD CAN Interface Device
780684-01
CAN Interface
1‑Port, Software‑Selectable/FD CAN Interface Device—The PCI‑8513 is a controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. NI‑XNET software-selectable CAN interfaces offer the best flexibility for CAN development with onboard transceivers for high-speed/FD, low-speed/fault-tolerant, and single-wire CAN as well as any external transceiver. The PCI‑8513 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
Product
Guidance Laser with Remote In-Cab Line Adjust
GL3000P
-
The GL3000P Guidance Laser uses an ultra high visibility green laser to establish visual line control for the vehicle driver. Used for highway paint striping, asphalt distributors, road wideners, pavement profilers, or virtually any application requiring vehicle line control. GL3000P model is for truck cab mounting.
-
Product
MIL-STD-1553 PMC Interface Module
PMC-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - 3.3v PMC (with 5V Tolerant I/O), 64-bit 33/66MHz - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Slipping Torque Detector
DI-12 series (SL4/SL02/SL15)
-
Torque measurement of tightened screws. Measure how much force the tightened screw is tightened. By capturing the occurrence of slippage with high accuracy and measuring the torque, it is now possible to measure the torque value of a tightened screw. For sampling inspection of products and setting and management of output torque of power drivers.
-
Product
USB-6343, 32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device
781439-01
Multifunction I/O
32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device - The USB‑6343 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6343 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Dual Port Simulator Fiber Channel XMC Module
XMC-FC4 Simulyzer
Simulator
*Two independent fiber channel ports*The two SFPs accept electrical as well as optical transceivers*Each port supports 1, 2, or 4 Gbps*Supports customer-specific defined transmission speed*Comprehensive decoding of FC-1, FC-2 and Upper Layer Protocol (ULP) frames*Triggering and filtering*Supports DMA for high-speed streaming*IRIG-B time code encoder / decoder for data correlation*Supports ULPs such as FC-AE-ASM, FC-AE-RDMA, FC-AE-1553 and FC-AV*Supports HS-1760E applications such as AS5653, AS5652 and AS5627*Optional fcXplorer, Windows-based FC simulation and analysis test software*FC SDK (Software Development Kit) provides drivers and APIs for Windows XP / 7,*Linux, VxWorks, QNX Neutrino RTOS and others on request
-
Product
Laser
BDS-SM Series
-
*Pulse Width Down to 60 ps*Repetition Rate 20 MHz /50 MHz / 80 MHz / CW (Switchable)*Free Beam or Fiber Output*All Electronics Integrated*No External Driver Unit*Simple +12 V Supply*40 mm x 70 mm x 120 mm
-
Product
(2×32)-Ch 1A-1500VDC 24VAC Matrix
YAV90097
Matrix Switch Module
32-Lines selectable High-Open-Low connection 3kV 1,0A Relays (Cool connection) Hipot test capabilities CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Product
PXI Flexible Microwave Module, Dual SP6T Terminated 40 GHz, Single SPDT 40 GHz, 50 Ω, SMA
40-890-006
Microwave Switch Module
The 40-890 (PXI) and 42-890 (PXIe) range of PXI microwave modules allows users to specify the mix of relay types, frequencies and quantities based on the application requirements within the capabilities of the module driver card. Choose from the extensive relay selection already available in the Pickering microwave range to create a flexible solution.
-
Product
Digital Torque Meter Torsion Tester
HN-1E~20E
-
Shenzhen Chuangxin Instruments Co., Ltd.
Digital Torque Meter is an intelligent metrologic instrument, which is designed for various torque test and calibration. It's mainly used for electic/manual torque drive, torque screwdrivers, bolt driver, tension wrench and other testers and products which refer to tightening force. It is widely applied in these industries, such as electrical manufacturing, machine manufacturing, car light industry, professional research and tests, and so on.
-
Product
Data Acquisition
-
We offer a full range of high quality data acquisition systems, starting from small, single or double channel systems, up to big multichannel systems. The smaller systems can identify themselves to the operating system as soundcards, for the bigger systems we deliver MatLab and DasyLab application drivers.
-
Product
PCI Digital IO Board
-
*Bus Interface: PCI Bus*Counter/Timer: 16 Channels*Counter Size: 32 bit*Max. Source Frequency: 80MHz*Compatibility: 5 V TTL/CMOS*Discrete Inputs: 24 Channels*Discrete Outputs: 24 Channels*Pulse Generation: 12 Channels*Bi directional I/O's: 8 Channels*Oscillator stability: 50 ppm*Op-to isolation for I/O's*DMA buffered operation*16-bit data bus 32 bit Address bus for External Memory Interface*The Pulse Width and PRI of the pulses can be varied*The pulse generation frequency from 10Hz to 40MHz (25ns to 100msec)*The no. of pulses controlled from 1 to 255 pulses*All the pulse input and the output signals and Bi-directional write signals driven through Pin Driver*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
16 Channel WDM Mux/DeMux
S-106
-
16CH WDM Mux/DeMux module of FOTS system offers a function of multiplexing or demultiplexing up to 16 channel of WDM signals. This module offers low insertion loss, low crosstalk, and high temperature stability. An internally built-in AWG module functions as 1 X N optical Multi/Demultiplexers. The bi-directional feature of this module is ideal for wide range of applications. In combination with an optionally built-in circulator or C/L-band WDM coupler, this module can be applied to the WDM-PON test. User can easily make his or her test set-ups for FTTX-PON systems, especially for WDM-PON test, by combining this module with other FOTS modules such as SLED Driver, SOA Driver, C+L-FOTS modules such as SLED Driver, SOA Driver, C+L-band ASE source, Wavelingth meter, Transceiver Driver and so on.
-
Product
PXI-6229, 32 AI (16-Bit, 250 kS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module
779115-01
Multifunction I/O
32 AI (16-Bit, 250 kS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module—The PXI‑6229 offers analog I/O, correlated digital I/O, two 32‑bit counter/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
