Load Banks
Test a power source by providing controlled amounts of load to create conditions found in thier application.
See Also: AC Load Banks, DC Load Banks, Inductive Load Banks, Reactive Load Banks, Resistive Load Banks
-
Product
DC Electronic Load Modules For The N6700 Power System
-
Test devices that store or convert energy by adding a DC electronic load to your Keysight N6700 Series power supply. The Keysight N6790 Series electronic load modules can perform a static or dynamic test and are available in two sizes: single-wide 100 W and double-wide 200 W modules.
-
Product
Hand-Held Alternator/Battery Load Tester
6024
-
• Full 125 Amp load tests 12 Volt and 24 Volt Batteries, alternators and starters on all types of vehicles• PATENTED• Made in USA of US and Global Components
-
-
Product
SIM, Module, ITA, 90 Series, Fully Loaded with pairs of VTAC Standard Pass-Thru and Right Angle Inserts (610151106)
510171102
ITA Module
This fully loaded SIM module kit comes with 34 pairs of VTAC Standard Pass-Thru and Right Angle Inserts (610151106). This kit also includes two PCB brackets for securing module to PCB.
-
Product
PXI MUX 4 Banks of 32 Channel 1 Pole
40-610-022-4/32/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
Low Profile Compressive Load Cell
CCLP-1.0
-
Low Profile Compressive Load Cell – 0.5t to 20t
-
Product
SWITCHABLE FILTER BANKS
FLT-1 WB
-
Matrix Test Equipment Incorporated
The Model FLT-1-WB is our Wide Bandpass filters for measuringthe Video Carrier and the Composite Second Order Beatdistortion on both sides of the carrier.
-
Product
Electronic Loads
T3EL Series
-
The T3EL series is a family of single channel, 200 & 300 Watt Electronic Loads that are ideal for R&D, product validation and Q&A in a bench or automated environment for low to medium power applications starting from 60mA, such as electronic components, batteries, portable chargers and power products. Electronic Loads are typically used to provide a load to the outputs of a power supply, usually capable of dynamic loading, and are fully programmable. Electronic Loads help designers to test electronic power products and ensure quality, reliability, and performance.
-
Product
High Power DC Electronic Load
63200A series
-
The 63200A series high power DC electronic loads are designed for testing a wide range of power conversion products including AC/DC and server power supplies, DC/DC converters, EV batteries, automotive charging stations, and other power electronics components. These units can be synchronously paralleled up to 240kW and dynamically synchronized for generating complex multi-channel transient profiles. The 300% peak overpower capability provides extra headroom for fault condition simulations in automotive batteries, fuel cells, and more. The 63200A series have three operating voltage choices, 150V, 600V & 1,200V, with models covering power levels from 4kW to 24kW and up to 2,000A in a single unit. The DC loads have unique user defined waveform (UDW) capability and external analog modulating input for s imul a t ing re a l-wor ld, cus tom waveforms. Another distinct feature is the dynamic auto-frequency sweep function, which enables detecting a UUTs worst case output deviation across a wide range of current frequencies. In addition, a 255-set of data storage function has been built in for recall of the stored settings at any time. For automated testing, the save and recall functions can save a great deal of time.
-
Product
Load Cell Indicator
9840
-
The 9840 is suitable for use in calibration labs, field service, or anywhere high accuracy is important. Features include a bipolar 6-digit 2-line display, remote sense, low noise, 22-bit resolution, USB port with RS232 communication, mV/V calibration and the ability to store up to 25 different sensors. 6-point linearization, unit conversion, front-panel tare. Self calibration via TEDS Plug & Play ready IEEE1451.4 compliance.
-
Product
PET Bottle Vertical Load Tester
VP-1000
-
VP-1000 PET Bottle Vertical Load Tester is professionally designed to test the top load resistance, container body side load resistance of the PET container.
-
Product
PowerSync Programmable Load
PSL-3424M
-
Sifos Technologies offers one-box platforms to facilitate analysis of Power Sourcing Equipment (PSE) behaviors. The PSL-3424M is Sifos’ lowest cost, multi-port PSE test instrument supporting PSE loading and power stressing. Depending upon configuration, up to 12 ports can simultaneously load over 1200 combined watts, emulating 802.3at and 802.3bt single signature PD’s advertising Class 0 to Class 8. With per-slot multiplexing, up to 24 PSE ports can be connected enabling automated test strategies covering 24, 16, or 8 port PSE’s.
-
Product
PXI 20 Banks of 4 Channel 2 Pole MUX
40-615-022-20/4/2
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
Wheel Running Tester up to 15000 kg axle load
MINC II EURO | VP 420005
-
Maschinenbau Haldenwang GmbH & Co. KG.
The test lane-compatible MINC II EURO guarantees a verification of the axle geometry in seconds when the test vehicle drives over (up to 15.0 t axle load) as well as a fully automatic evaluation of the deviation in m / km. The measured values are displayed either in analog form on a dial or by transmission to a PC screen (including graphic representation).
-
Product
Digital Roller Brake Tester for Cars and Vans up to 5.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,800mm
C_MBT C 5.0 W280 | VP 210160
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 5.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,800 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes for large and heavy cars and vans, and with increased loads.
-
Product
Load Cells and Sensors
-
AMETEK Sensors, Test & Calibration
Our high quality load cells and sensors are used for materials testing and force measurement all over the world.The full bridge load cells and sensors provide high precision measurements that ensure adherence to the international standards.
-
Product
Signal, Module, Receiver, QuadraPaddle, iCon Series, 160 Position, loaded w/ Twin Female Contacts and Round Posts
510160122
Receiver Module
Fully Loaded with Twin Female Contacts and Round Posts (Adapter Pins) (p/n's 610138200 and 610138117).Primary mating module 510161101. (May mate with other ITA modules, as well.)
-
Product
Electronic Loads
-
PeakTech Prüf- und Messtechnik GmbH
Can be used for important test procedures in quality assurance as well as e.g. testing of power supplies and control units, batteries, fuel and solar cells. For precise load control for various purposes, this device offers load control according to constant voltage (CV), constant current (CC), constant load resistance (CR) or constant power (CP) with a highly precise resolution of 1mW, 1mV, 1mΩ and 1mA. The device also offers additional test modes, e.g. the battery test or the dynamic test. The PC interface and software offer the option of implementing freely programmable test sequences with data evaluation.
-
Product
Low Voltage Capacitor Banks
-
Wide range of capacitor banks to correct the power factor in low-voltage electrical installations, for both 50 Hz and 60 Hz networks. Avoid surcharges on the electric bill and improve the capacity of the installation.
-
Product
Signal, Module, Receiver, QuadraPaddle, 90 Series, 192 Position, Fully Loaded w/ Twin Female Contacts & Square Posts for Wire Wrap (p/n's 610138200 & 610138118)
510150136
Receiver Module
Primary mating module 510151105. (May mate with other ITA modules, as well.)
-
Product
Terminations (Loads)
-
Loads find wide use as accessories for both broadband and narrowband measurement instruments. Keysight's family of fixed and sliding loads includes both general purpose grade loads as well as loads intended for use as calibration standards.
-
Product
DC Electronic Load
EE30181A
-
The EE30181A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control. attach the electronic load block to a heat- sink and your up and running. used them with D to A's, A to D's, Pots, PLC's to control the current
-
Product
Static Load Cells (500 N to 600 kN)
2580 Series
-
The Instron 2580 Series static load cells are high-precision force transducers optimized for use with 5900 and 6800 Series universal testing systems, capable of measuring loads across a wide range (up to ±600 kN) with accuracy to 0.5 % of reading and sensitivity down to 1/1000th of full scale. Temperature-compensated and calibrated on equipment traceable to international standards, they have automatic recognition with an electronic serial number and support electronic calibration, while offering overload protection (up to 150 % without damage, 300 % without mechanical failure). The 2580’s design delivers high stiffness and reliable alignment under load—making it a robust choice for tension, compression, cyclic, and reverse stress testing in materials and components.
-
Product
Signal Module, ITA, QuadraPaddle, 480 Position, Fully Loaded With Round Posts (610 138 115)
510151108
ITA Module
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
Product
Oscilloscope, 350 MHz, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch DSO, Fully Loaded with 10.1" Color Display
T3DSO2354HD
Oscilloscope
The T3DSO2000HD series of Bench Oscilloscopes feature 4-channel models with analog bandwidth options of 100 MHz, 200MHz and 350 MHz. The T3DSO2000HD Oscilloscopes use 12-bit high resolution ADCs and a low noise front end which provides an impressive noise performance to cover a wide range of measurement applications. Each model offers a maximum sample rate of 2 GSa/s (interleaved) and a maximum memory depth of 200 Mpts in interleave mode. The MS configured models also include a 16 channel logic probe as standard.
-
Product
Receiver, I2 Micro ICon, 168 Position, Fully Loaded With Twin Female Contacts (610 138 200)
310130101
Receiver
The i2 Micro iCon receiver is a one piece connector capable of holding up to 168 QuadraPaddle contacts. QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. This i2 receiver is fully loaded with twin female contacts, QuadraPaddle Part # 610 138 200. Accessories such as keying pin kit, protective cover, and strain relief are available.
-
Product
3U VPX Conduction Cooled Load Board
1940000446-0000R
-
3U VPX Load Board, conduction cooled.
-
Product
Three Phase Phantom Load Test Bench
-
Supreme Instrument Laboratories
Supreme make Phantom Load Test Set is a portable testing accessory designed for field service. It simulates various load conditions usually prevailing in power supply system. The unit offers a practical solution by providing artificial load unaltered by the variation in the power supply mains and adjustable to the complete meter testing requirements.
-
Product
PXI 10 Banks of 16 Channel 1 Pole MUX
40-615-022-10/16/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration. Connections are made via a front panel 200-pin connector.
-
Product
Signal / Micro Power/ Micro Coax, Module, Receiver, QuadraPaddle, iCon Series, 100/15 Position, loaded w/twin female contacts
510160112
Receiver Module
This module comes fully loaded with twin female contacts (p/n 610138200), iCon modules mount from the rear of the iCon/i1 receiver allowing installation and removal of pre-wired cable blocks. Primary mating module 510161107. (May mate with other ITA modules, as well.)
